Camera: Xiaomi MJSXJ03HL
You can choose between:
- Quick installation method, which doesn't require dismantling the camera, but doesn't (fully) backup the original firmware
- Safe installation, which requires camera dismantling. Allows full backup of original firmware, and recovery from corrupted flash
See: https://github.com/Andrik45719/MJSXJ03HL
First, dismantle camera to access flash chip:
- Gently warm up the front of the camera (where the lens is). See pictures below.
- Using a utility knife or other pointed object, carefully pry off the front part. Remember, there are important wires under the front, don't damage them!
- After the front part is removed, unscrew 2 screws holding the two halves of the camera together
Then use either cloner or CH341 to backup and reprogram flash:
- Ingenic USB Cloner + flash pin short trick and reprogram via USB port (requires a USB OTG port on the camera, USB cable with data lines), or:
- CH341 programming clip on the chip on the board and re-program in place (requires a programmer and a clip).
- Model: Xiaomi MJSXJ03HL
- Product name: Mi Camera 2K (Magnetic Mount)
- Type: indoor camera
- Weather resistance: no IP rating
- CPU: Ingenic T31L or T31N
- RAM: 64MB
- Flash: 16MB
- Video encoding: H.264, H.265, MJPG
- Sensor: SOI (Silicon Optronics Inc) JX-Q03P, 2304 x 1296 @ 30FPS, RGGB Bayer filter
- Sensor optical format: 1/2.7", active area: 5.76 mm x 3.24 mm, pixel: 2.5 um x 2.5 um
- Lens: unk mm, unk mount, total length (sensor to lens edge): unk mm
- Field of View: Horizontal 125 degrees
- Optical resolution: unk TVL
- IR cut filter: Yes, mechanical shutter with solenoid, controlled by GPIO
- WIFI module: RTL8189FTV, 802.11n 20/40MHz, 2.4GHz only, 150Mbps
- Microphone: Yes
- Speaker: Yes
- SD card slot: Yes
- reset button: Yes
- Illumination:
- White LEDs: No
- IR 850nm LEDs: No
- IR 940nm LEDs: Yes, 6x, controlled by GPIO
- Power consumption: 5V 1A
- Operating temperature: -10 C to +50 C
- FCC ID: unk
- Pan / Tilt / Zoom motors: No
- Ethernet interface: No
- USB: Yes, USB type C, with data lines
- Vendor app: Mi Home (not compatible with thingino)
Click here
U-Boot SPL 2013.07-g8581847-dirty (Aug 09 2021 - 18:07:12)
Timer init
CLK stop
PLL init
pll_init:366
pll_cfg.pdiv = 10, pll_cfg.h2div = 5, pll_cfg.h0div = 5, pll_cfg.cdiv = 1, pll_cfg.l2div = 2
nf=84 nr = 1 od0 = 1 od1 = 2
cppcr is 05405100
CPM_CPAPCR 0540510d
nf=100 nr = 1 od0 = 1 od1 = 2
cppcr is 06405100
CPM_CPMPCR 0640510d
nf=100 nr = 1 od0 = 1 od1 = 2
cppcr is 06405100
CPM_CPVPCR 0640510d
cppcr 0x9a7b5510
apll_freq 1008000000
mpll_freq 1200000000
vpll_freq = 1200000000
ddr sel mpll, cpu sel apll
ddrfreq 600000000
cclk 1008000000
l2clk 504000000
h0clk 240000000
h2clk 240000000
pclk 120000000
CLK init
SDRAM init
sdram init start
ddr_inno_phy_init ..!
phy reg = 0x00000007, CL = 0x00000007
ddr_inno_phy_init ..! 11: 00000004
ddr_inno_phy_init ..! 22: 00000006
ddr_inno_phy_init ..! 33: 00000006
REG_DDR_LMR: 00000210
REG_DDR_LMR: 00000310
REG_DDR_LMR: 00000110
REG_DDR_LMR, MR0: 00f73011
T31_0x5: 00000007
T31_0x15: 0000000c
T31_0x4: 00000000
T31_0x14: 00000002
INNO_TRAINING_CTRL 1: 00000000
INNO_TRAINING_CTRL 2: 000000a1
T31_cc: 00000003
INNO_TRAINING_CTRL 3: 000000a0
T31_118: 0000003c
T31_158: 0000003c
T31_190: 0000001e
T31_194: 0000001c
jz-04 : 0x00000051
jz-08 : 0x000000a0
jz-28 : 0x00000024
DDR PHY init OK
INNO_DQ_WIDTH :00000003
INNO_PLL_FBDIV :00000014
INNO_PLL_PDIV :00000005
INNO_MEM_CFG :00000051
INNO_PLL_CTRL :00000018
INNO_CHANNEL_EN :0000000d
INNO_CWL :00000006
INNO_CL :00000007
DDR Controller init
DDRC_STATUS 0x80000001
DDRC_CFG 0x0a288a40
DDRC_CTRL 0x0000011c
DDRC_LMR 0x00400008
DDRC_DLP 0x00000000
DDRC_TIMING1 0x050f0a06
DDRC_TIMING2 0x021c0807
DDRC_TIMING3 0x20080723
DDRC_TIMING4 0x1f240031
DDRC_TIMING5 0xff060405
DDRC_TIMING6 0x321c0505
DDRC_REFCNT 0x00918403
DDRC_MMAP0 0x000020fc
DDRC_MMAP1 0x00002400
DDRC_REMAP1 0x03020d0c
DDRC_REMAP2 0x07060504
DDRC_REMAP3 0x0b0a0908
DDRC_REMAP4 0x0f0e0100
DDRC_REMAP5 0x13121110
DDRC_AUTOSR_EN 0x00000000
sdram init finished
SDRAM init ok
board_init_r
image entry point: 0x80100000
U-Boot 2013.07-g8581847-dirty (Aug 09 2021 - 18:07:12)
Board: ISVP (Ingenic XBurst T31 SoC)
DRAM: 64 MiB
Top of RAM usable for U-Boot at: 84000000
Reserving 436k for U-Boot at: 83f90000
Reserving 32772k for malloc() at: 81f8f000
Reserving 32 Bytes for Board Info at: 81f8efe0
Reserving 124 Bytes for Global Data at: 81f8ef64
Reserving 128k for boot params() at: 81f6ef64
Stack Pointer at: 81f6ef48
Now running in RAM - U-Boot at: 83f90000
MMC: msc: 0
the manufacturer ef
SF: Detected W25Q128
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
misc_init_r before change the wifi_enable_gpio
gpio_request lable = wifi_enable_gpio gpio = 58
misc_init_r after gpio_request the wifi_enable_gpio ret is 58
misc_init_r after change the wifi_enable_gpio ret is 0
misc_init_r before change the yellow_gpio
gpio_request lable = yellow_gpio gpio = 39
misc_init_r after gpio_request the yellow_gpio ret is 39
misc_init_r after change the yellow_gpio ret is 1
misc_init_r before change the blue_gpio
gpio_request lable = blue_gpio gpio = 38
misc_init_r after gpio_request the blue_gpio ret is 38
misc_init_r after change the blue_gpio ret is 0
gpio_request lable = night_gpio gpio = 60
misc_init_r after gpio_request the night_gpio ret is 60
misc_init_r after change the night_gpio ret is 0
gpio_request lable = SPK_able_gpio gpio = 63
misc_init_r after gpio_request the SPK_able_gpio ret is 63
misc_init_r after change the SPK_able_gpio ret is 0
gpio_request lable = TF_en_gpio gpio = 47
misc_init_r after gpio_request the TF_en_gpio ret is 47
misc_init_r after change the TF_en_gpio ret is 0
gpio_request lable = TF_cd_gpio gpio = 48
misc_init_r after gpio_request the TF_cd_gpio ret is 48
misc_init_r after change the TF_cd_gpio ret is 1
gpio_request lable = SD_able_gpio gpio = 54
misc_init_r after change the SD_able_gpio ret is 1
misc_init_r before change the wifi_enable_gpio
gpio_request lable = wifi_enable_gpio gpio = 58
misc_init_r after gpio_request the wifi_enable_gpio ret is 58
misc_init_r after change the wifi_enable_gpio ret is 1
Hit any key to stop autoboot: 0
Card did not respond to voltage select!
SD card is not insert
gpio_request lable = sdupgrade gpio = 51
the manufacturer ef
SF: Detected W25Q128
The upgrade flag could not be found!
the manufacturer ef
SF: Detected W25Q128
--->probe spend 4 ms
SF: 2031616 bytes @ 0x40000 Read: OK
--->read spend 653 ms
## Booting kernel from Legacy Image at 80600000 ...
Image Name: Linux-3.10.14__isvp_swan_1.0__
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1590203 Bytes = 1.5 MiB
Load Address: 80010000
Entry Point: 80367840
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
Click here
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.14__isvp_swan_1.0__ (xuxuequan@ubuntu) (gcc version 4.7.2 (Ingenic r2.3.3 2016.12) ) #0 PREEMPT Mon Jul 12 02:36:24 CST 2021
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 RESET ERROR PC:00404E1C
[ 0.000000] CPU0 revision is: 00d00100 (Ingenic Xburst)
[ 0.000000] FPU revision is: 00b70000
[ 0.000000] CCLK:1008MHz L2CLK:504Mhz H0CLK:200MHz H2CLK:200Mhz PCLK:100Mhz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 00473000 @ 00010000 (usable)
[ 0.000000] memory: 0002d000 @ 00483000 (usable after init)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 02a00000 @ 00000000 (usable)
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x029fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x029fffff]
[ 0.000000] Primary instruction cache 32kB, 8-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] pls check processor_id[0x00d00100],sc_jz not support!
[ 0.000000] MIPS secondary cache 128kB, 8-way, linesize 32 bytes.
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 10668
[ 0.000000] Kernel command line: console=ttyS1,115200n8 mem=42M@0x0 rmem=22M@0x2A00000 init=/linuxrc rootfstype=squashfs root=/dev/mtdblock2 rw mtdparts=jz_sfc:256K(boot),1984K(kernel),3904K(rootfs),3904K(app),1984K(kback),3904K(aback),384K(cfg),64K(para)
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 37216k/43008k available (3456k kernel code, 5792k reserved, 1098k data, 180k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:358
[ 0.000000] clockevents_config_and_register success.
[ 0.000018] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408)
[ 0.037791] pid_max: default: 32768 minimum: 301
[ 0.042706] Mount-cache hash table entries: 512
[ 0.047728] Initializing cgroup subsys debug
[ 0.051986] Initializing cgroup subsys freezer
[ 0.058588] regulator-dummy: no parameters
[ 0.062808] NET: Registered protocol family 16
[ 0.079039] bio: create slab <bio-0> at 0
[ 0.084968] jz-dma jz-dma: JZ SoC DMA initialized
[ 0.090040] usbcore: registered new interface driver usbfs
[ 0.095590] usbcore: registered new interface driver hub
[ 0.101020] usbcore: registered new device driver usb
[ 0.106238] (null): set:249 hold:250 dev=100000000 h=500 l=500
[ 0.112344] (null): set:61 hold:62 dev=100000000 h=125 l=125
[ 0.118290] media: Linux media interface: v0.10
[ 0.122841] Linux video capture interface: v2.00
[ 0.129304] Switching to clocksource jz_clocksource
[ 0.134758] jz-dwc2 jz-dwc2: cgu clk gate get error
[ 0.139727] cfg80211: Calling CRDA to update world regulatory domain
[ 0.146169] DWC IN OTG MODE
[ 0.149576] dwc2 dwc2: Keep PHY ON
[ 0.152944] dwc2 dwc2: Using Buffer DMA mode
[ 0.157298] dwc2 dwc2: Core Release: 3.00a
[ 0.161455] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller
[ 0.167807] dwc2 dwc2: new USB bus registered, assigned bus number 1
[ 0.174803] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.181616] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.188980] usb usb1: Product: DesignWare USB2.0 High-Speed Host Controller
[ 0.196020] usb usb1: Manufacturer: Linux 3.10.14__isvp_swan_1.0__ dwc2-hcd
[ 0.203069] usb usb1: SerialNumber: dwc2
[ 0.207390] hub 1-0:1.0: USB hub found
[ 0.211120] hub 1-0:1.0: 1 port detected
[ 0.215316] dwc2 dwc2: DWC2 Host Initialized
[ 0.219767] NET: Registered protocol family 2
[ 0.224677] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.231596] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.238071] TCP: Hash tables configured (established 512 bind 512)
[ 0.244358] TCP: reno registered
[ 0.247565] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.253490] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.260094] NET: Registered protocol family 1
[ 0.264472] dwc2 dwc2: ID PIN CHANGED!
[ 0.268660] freq_udelay_jiffys[0].max_num = 10
[ 0.273088] cpufreq udelay loops_per_jiffy
[ 0.277546] 12000 59635 59635
[ 0.280769] 24000 119271 119271
[ 0.284224] 60000 298179 298179
[ 0.287656] 120000 596358 596358
[ 0.291188] 200000 993930 993930
[ 0.294730] 300000 1490895 1490895
[ 0.298428] 600000 2981790 2981790
[ 0.302136] 792000 3935963 3935963
[ 0.305854] 1008000 5009408 5009408
[ 0.309640] 1200000 5963580 5963580
[ 0.318433] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.324518] jffs2: version 2.2. © 2001-2006 Red Hat, Inc.
[ 0.330336] msgmni has been set to 72
[ 0.335016] io scheduler noop registered
[ 0.338944] io scheduler cfq registered (default)
[ 0.345247] jz-uart.1: ttyS1 at MMIO 0x10031000 (irq = 58) is a uart1
[ 0.353182] console [ttyS1] enabled, bootconsole disabled
[ 0.353182] console [ttyS1] enabled, bootconsole disabled
[ 0.367841] brd: module loaded
[ 0.372776] loop: module loaded
[ 0.376802] zram: Created 2 device(s) ...
[ 0.381016] logger: created 256K log 'log_main'
[ 0.386318] jz TCU driver register completed
[ 0.391089] the id code = ef4018, the flash name is WIN25Q128
[ 0.397096] JZ SFC Controller for SFC channel 0 driver register
[ 0.403234] 8 cmdlinepart partitions found on MTD device jz_sfc
[ 0.409384] Creating 8 MTD partitions on "jz_sfc":
[ 0.414377] 0x000000000000-0x000000040000 : "boot"
[ 0.419846] 0x000000040000-0x000000230000 : "kernel"
[ 0.425508] 0x000000230000-0x000000600000 : "rootfs"
[ 0.431098] 0x000000600000-0x0000009d0000 : "app"
[ 0.436488] 0x0000009d0000-0x000000bc0000 : "kback"
[ 0.441977] 0x000000bc0000-0x000000f90000 : "aback"
[ 0.447534] 0x000000f90000-0x000000ff0000 : "cfg"
[ 0.452848] 0x000000ff0000-0x000001000000 : "para"
[ 0.458311] SPI NOR MTD LOAD OK
[ 0.461623] tun: Universal TUN/TAP device driver, 1.6
[ 0.466880] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 0.473382] usbcore: registered new interface driver zd1201
[ 0.479289] usbcore: registered new interface driver usbserial
[ 0.485384] usbcore: registered new interface driver ch341
[ 0.491090] usbserial: USB Serial support registered for ch341-uart
[ 0.497618] usbcore: registered new interface driver usb_debug
[ 0.503670] usbserial: USB Serial support registered for debug
[ 0.509740] usbcore: registered new interface driver pl2303
[ 0.515538] usbserial: USB Serial support registered for pl2303
[ 0.521660] i2c /dev entries driver
[ 0.525690] jzmmc_v1.2 jzmmc_v1.2.0: vmmc regulator missing
[ 0.531794] jzmmc_v1.2 jzmmc_v1.2.0: register success!
[ 0.537246] jzmmc_v1.2 jzmmc_v1.2.1: vmmc regulator missing
[ 0.543164] jzmmc_v1.2 jzmmc_v1.2.1: register success!
[ 0.548787] TCP: cubic registered
[ 0.552219] NET: Registered protocol family 17
[ 0.557618] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 0.564768] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 0.576456] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.584036] Freeing unused kernel memory: 180K (80483000 - 804b0000)
mdev is ok......
[ 1.127731] jffs2: Node at 0x00007958 with length 0x00000bff would run over the end of the erase block
[ 1.137481] jffs2: Perhaps the file system was created with the wrong erase size?
[ 1.145257] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000795c: 0x0bff instead
[ 1.155089] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00007960: 0xdd67 instead
[ 1.164913] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00007964: 0x000d instead
[ 1.174729] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00007968: 0x0009 instead
[ 1.184543] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000796c: 0x81fd instead
[ 1.194355] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00007970: 0x03e8 instead
[ 1.204158] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00007974: 0x6ff8 instead
[ 1.213969] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00007978: 0xd534 instead
[ 1.223782] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000797c: 0xd534 instead
[ 1.233595] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00007980: 0xd534 instead
[ 1.243403] jffs2: Further such events for this erase block will not be printed
[ 1.251203] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008000: 0x22ae instead
[ 1.261024] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008004: 0xe117 instead
[ 1.270875] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008008: 0x7e11 instead
[ 1.280694] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000800c: 0x7df0 instead
[ 1.290508] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008010: 0xb423 instead
[ 1.300321] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008014: 0x75cf instead
[ 1.310133] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008018: 0x410d instead
[ 1.319946] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000801c: 0xf0aa instead
[ 1.329757] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008020: 0xce52 instead
[ 1.339569] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008024: 0xc9ec instead
[ 1.349377] jffs2: Further such events for this erase block will not be printed
[ 1.440700] exFAT: Version 1.2.9
[ 1.474782] jz_codec_register: probe() successful!
[ 1.884463] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06 desc a1817000)
[ 1.893634] dma dma0chan25: Channel 25 have been requested.(phy id 6,type 0x06 desc a27e0000)
[ 1.902912] dma dma0chan26: Channel 26 have been requested.(phy id 5,type 0x04 desc a27ea000)
[ 1.955109] jz_pwm_probe[212] d_name = tcu_chn0
[ 1.961923] The version of PWM driver is H20180309a
[ 1.974047] request pwm channel 0 successfully
[ 1.981097] pwm-jz pwm-jz: jz_pwm_probe register ok !
[ 2.312105] RTL871X: module init start
[ 2.316083] RTL871X: rtl8189ftv v4.3.24.7_21113.20170208.nova.1.02
[ 2.322480] RTL871X: build time: Aug 14 2020 13:46:20
[ 2.327786] wlan power on
[ 2.344641] RTL871X: module init ret=0
[ 2.390089] mmc1: card claims to support voltages below the defined range. These will be ignored.
[ 2.425035] mmc1: new SDIO card at address 0001
[ 2.436291] RTL871X: ++++++++rtw_drv_init: vendor=0x024c device=0xf179 class=0x07
[ 2.490306] RTL871X: HW EFUSE
[ 2.493398] RTL871X: hal_com_config_channel_plan chplan:0x20
[ 2.679364] RTL871X: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1
[ 2.706802] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=c8:5c:cc:93:22:96
[ 2.803476] @@@@ tx-isp-probe ok(version H20210112a), compiler date=Jan 12 2021 @@@@@
[ 2.815241] zram0: detected capacity change from 0 to 16777216
Setting up swapspace version 1, size = 16773120 bytes
UUID=1903dcaa-6bab-48b3-996c-9[ 2.828234] Adding 16380k swap on /dev/zram0. Priority:-1 extents:1 across:16380k SS
ebe6ff470a3
[FC] step1 export sd power and en
[FC] step2 poweron sd card
[ 3.164210] jzmmc_v1.2 jzmmc_v1.2.0: card inserted, state=0
[FC] step3 trigger cd pin
mount: mounting /dev/mmcblk0 on /media/mmc failed: No such file or directory
===========welcome to assis process=========
[Build date] Oct 4 2021 (09:08:09)
[exec-assis,0144]msgSndId:0
[exec-assis,0159]msgRcvId:32769
[SDK-DOG]dbg: turn on watchdog success!
===========welcome to iCamera_app===========
[Build date] Oct 4 2021 (09:08:10)
[msg:79]log: msg_queue_create() ok MsgId:65538
[sdevice_not_work_set_callback]dbg: set ok! have 1 cb
[sdevice_can_work_set_callback]dbg: set ok! have 1 cb
init_log_module() ok
[sdevice_can_work_set_callback]dbg: set ok! have 2 cb
[exec-iCame,0144]msgSndId:0
[exec-iCame,0159]msgRcvId:32769
[timer,144]dbg: init complete.
open gpio direction: No such file or directory
[ 9.420662] name : i2c0 nr : 0
[ 9.504378] error: sensor_read,291 ret = -5
[ 9.508733] sensor_read: addr=0x3107 value = 0x0
[ 9.513592] err sensor read addr = 0x3107, value = 0x0
[ 9.604373] error: sensor_read,291 ret = -5
[ 9.608700] sensor_read: addr=0xf0 value = 0x0
[ 9.613544] err sensor read addr = 0xf0, value = 0x0
[ 9.618714] jzmmc_v1.2 jzmmc_v1.2.0: card removed, state=0
[ 9.714704] sensor_read: addr=0xa value = 0x8
[ 9.804698] sensor_read: addr=0xa value = 0x8
[ 9.894696] sensor_read: addr=0xa value = 0x8
[ 9.899801] sensor_read: addr=0xb value = 0x43
[ 9.904532] info: success sensor find : jxq03p
[ 9.909128] name : i2c1 nr : 1
[ 9.912300] misc sinfo_release
[ 10.054698] -----jxq03p_detect: 589 ret = 0, v = 0x08
[ 10.060431] -----jxq03p_detect: 597 ret = 0, v = 0x43
[ 10.065838] jxq03p chip found @ 0x40 (i2c0)
[ 10.070206] sensor driver version H20200930b
[ 10.277969] jxq03p stream on
---- FPGA board is ready ----
Board UID : 30AB6E51
Board HW ID : 72000460
Board rev. : 5DE5A975
Board date : 20190326
-----------------------------
[ 10.874247] codec_set_device: set device: MIC...
[ 11.194275] codec_set_device: set device: speaker...
[ 11.200831] SPEAKER CTL MODE1 !
up
[ 14.071537] SPEAKER CTL MODE1 !
[ 18.105018] SPEAKER CTL MODE0 !
[ 18.672243] SPEAKER CTL MODE1 !
killall: miio_client: no process killed
killall: miio_client_helper_nomqtt.sh: no process killed
killall: wifi_start.sh: no process killed
Jan 1 08:00:19 miio_client[272]: [W] miio_client: version: miio-client 4.1.6 (main,277)
Jan 1 08:00:19 miio_client[274]: [W] internal: handle_internal_hello, fd: 7, STATE: (0) (handle_internal_hello,2211)
Jan 1 08:00:19 miio_client[274]: [W] internal: cmd_internal_response_dinfo:1846 STATE: [STATE_DEVICE_INIT] -> [STATE_DIDKEY_DONE] (_set_conn_state,540)
Jan 1 08:00:19 miio_client[274]: [W] internal: handle_internal_hello, fd: 12, STATE: (3) (handle_internal_hello,2211)
Jan 1 08:00:19 miio_client[274]: [W] internal: ssid not string (cmd_internal_response_ot_config,1958)
Jan 1 08:00:19 miio_client[274]: [W] internal: password not string (cmd_internal_response_ot_config,1981)
Jan 1 08:00:19 miio_client[274]: [W] internal: country not string (cmd_internal_response_ot_config,2003)
Jan 1 08:00:19 miio_client[274]: [W] internal: uid not int (cmd_internal_response_ot_config,2026)
Jan 1 08:00:19 miio_client[274]: [W] internal: cmd_internal_response_ot_config:2035 STATE: [STATE_DIDKEY_DONE] -> [STATE_OT_CONFIG_DONE] (_set_conn_state,540)
Jan 1 08:00:19 miio_client[274]: [W] internal: handle_internal_hello, fd: 8, STATE: (4) (handle_internal_hello,2211)
Jan 1 08:00:19 miio_client[274]: [W] internal: cmd_internal_res_wifi_conf_status:644 STATE: [STATE_OT_CONFIG_DONE] -> [STATE_WIFI_AP_MODE] (_set_conn_state,540)
Jan 1 08:00:19 miio_client[274]: [W] internal: wifi enter AP mode (cmd_internal_res_wifi_conf_status,646)
Jan 1 08:00:19 miio_client[274]: [W] miio_client: miio_common init (main,336)
Jan 1 08:00:19 miio_client[274]: [W] internal: handle_internal_hello, fd: 8, STATE: (6) (handle_internal_hello,2211)
Jan 1 08:00:19 miio_client[274]: [W] internal: handle_internal_hello:2271 STATE: [STATE_WIFI_AP_MODE] -> [STATE_WIFI_MODE_MONITOR] (_set_conn_state,540)
killall: wpa_supplicant: no process killed
killall: udhcpc: no process killed
killall: udhcpd: no process killed
killall: hostapd: no process killed
killall: telnetd: no process killed
down
[ 20.415078] SPEAKER CTL MODE0 !
up
Configuration file: /tmp/hostapd_wpa2.conf
rfkill: Cannot open RFKILL control device
nl80211: Could not re-add multicast membership for vendor events: -2 (No such file or directory)
Using interface wlan0 with hwaddr e4:aa:ec:9c:c2:00 and ssid "isa-camera-hlc7_miapC200"
[ 21.605619] RTL871X: assoc success
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
[ 28.780798] SPEAKER CTL MODE1 !
[assis]WDG_CMD_FEED_DOG!!!!
[ 30.525009] SPEAKER CTL MODE0 !
[ 38.887856] SPEAKER CTL MODE1 !
[ 40.625019] SPEAKER CTL MODE0 !
[ 48.998751] SPEAKER CTL MODE1 !
[ 50.735091] SPEAKER CTL MODE0 !
[ 59.106661] SPEAKER CTL MODE1 !
[assis]WDG_CMD_FEED_DOG!!!!
[ 60.855023] SPEAKER CTL MODE0 !
[ 69.214791] SPEAKER CTL MODE1 !
[ 70.965059] SPEAKER CTL MODE0 !
[ 79.330846] SPEAKER CTL MODE1 !
[ 81.075021] SPEAKER CTL MODE0 !
[ 89.451911] SPEAKER CTL MODE1 !
[assis]WDG_CMD_FEED_DOG!!!!
[ 91.195015] SPEAKER CTL MODE0 !