Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

Sign up for GitHub

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Jump to bottom

ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B #16927

Merged
merged 1 commit into from
Nov 23, 2024
Merged

ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B #16927

merged 1 commit into from
Nov 23, 2024

Conversation

svobodavac
Copy link
Contributor

@svobodavac svobodavac commented Nov 11, 2024 •
edited
Loading

The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:

  • SoC: MT7628AN
  • RAM: 64 MB (Winbond W9751G6K8-25)
  • Storage: 8 MB SPI flash (S25FL064K)
  • Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
  • Wireless: 2.4GHz: on SoC (802.11b/g/n)
  • Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
  • LEDs: 8x
  • Buttons: 1x reset
  • USB: 1x 2.0
  • MicroSD slot: 1x
  • Power: 9 VDC, 1 A
  • Uart: GND TX RX PWR - J1 on the PCB
  • Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:

  • Using the bootloader web server. Hold the reset button while turning
    the power on. Upload the sysupgrade image on http://192.168.1.1.
  • Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:

  • LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
    (GPIOs 43,42,41,40,39,44)
  • WLAN5G uses pin of MT7612EN.
  • The POWER LED is directly connected to the VCC. It can be reconnected to
    the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:

  • The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:

use address source
2g *:b0 factory 0x4 (label)
5g *:b1 factory 0x8004
LAN *:b2 factory 0x28
WAN *:b3 factory 0x2e

@github-actions github-actions bot added the target/ramips pull request/issue for ramips target label Nov 11, 2024
@svobodavac svobodavac force-pushed the main branch 2 times, most recently from e6670dd to 8bd865c Compare November 15, 2024 22:47
@hauke
Copy link
Member

hauke commented Nov 17, 2024

Please check that the mac addresses for the Ethernet and wifi interfaces are correctly assigned that the LEDs work like with the vendor firmware.

@svobodavac
Copy link
Contributor Author

svobodavac commented Nov 18, 2024 •
edited
Loading

Please check that the mac addresses for the Ethernet and wifi interfaces are correctly assigned that the LEDs work like with the vendor firmware.

All MAC addresses and LEDs are OK. Thank you for your help.

@svobodavac @hauke
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
3a9752e 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
@openwrt-bot openwrt-bot merged commit 3a9752e into openwrt:main Nov 23, 2024
3 checks passed
svobodavac added a commit to svobodavac/openwrt that referenced this pull request Nov 23, 2024
@svobodavac
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
780a11a 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
svobodavac added a commit to svobodavac/openwrt that referenced this pull request Nov 23, 2024
@svobodavac
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
c8d9874 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
vincejv pushed a commit to vincejv/openwrt that referenced this pull request Nov 26, 2024
@svobodavac @vincejv
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
0e5de4e 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
vincejv pushed a commit to vincejv/openwrt that referenced this pull request Nov 26, 2024
@svobodavac @vincejv
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
03e09ec 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
ynezz pushed a commit to ynezz/openwrt that referenced this pull request Nov 27, 2024
@svobodavac @ynezz
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
73ce1d8 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
(cherry picked from commit 3a9752e)
ynezz pushed a commit to ynezz/openwrt that referenced this pull request Nov 28, 2024
@svobodavac @ynezz
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
50ee6ad 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
(cherry picked from commit 3a9752e)
Link: openwrt#17097
Signed-off-by: Petr Štetiar <[email protected]>
Vladdrako pushed a commit to Vladdrako/openwrt that referenced this pull request Dec 11, 2024
@svobodavac @Vladdrako
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
2bbd299 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
rmandrad pushed a commit to rmandrad/openwrt that referenced this pull request Dec 30, 2024
@svobodavac @rmandrad
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
b361dfa 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
M3m3M4n pushed a commit to M3m3M4n/openwrt that referenced this pull request Feb 16, 2025
@svobodavac @M3m3M4n
ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B
01c5d41 
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <[email protected]>
Link: openwrt#16927
Signed-off-by: Hauke Mehrtens <[email protected]>
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Reviewers

@hauke hauke hauke left review comments

@musashino205 musashino205 musashino205 left review comments

@raenye raenye raenye left review comments

Assignees
No one assigned
Labels
target/ramips pull request/issue for ramips target
Projects
None yet
Milestone
No milestone
Development

Successfully merging this pull request may close these issues.
5 participants
@svobodavac @hauke @musashino205 @raenye @openwrt-bot