Switch from ifname to device

Signed-off-by: Etienne Champetier <[email protected]>

README.md

@@ -42,25 +42,28 @@ opkg install phantap
 * Either reboot the device, or run `/etc/init.d/phantap setup`.
 * Get the interface names from that device:
 ```
-# uci show network | grep ifname
-network.loopback.ifname='lo'
-network.lan.ifname='eth1'
-network.wan.ifname='eth0'
-network.wan6.ifname='eth0'
+# uci show network | grep -E 'device=|ports='
+network.loopback.device='lo'
+network.@device[0].ports='eth0'
+network.lan.device='br-lan'
+network.wan.device='eth1'
+network.wan6.device='eth1'
+network.phantap.device='br-phantap'
 ```
 In this example we are using a GL-AR150, which only has 2 interfaces.
 
 * Remove the interfaces from any network interface they might be used by, if that's the case, via the following commands in the cli
 (assuming we are using a GL-AR150):
 ```
-uci delete network.lan.ifname
-uci delete network.wan.ifname
-uci delete network.wan6.ifname
+uci delete network.@device[0].ports
+uci delete network.wan.device
+uci delete network.wan6.device
 ```
 * Add the interfaces to the phantap bridge and restart the network service via the following commands in the cli
 (assuming we are using a GL-AR150):
 ```
-uci set network.phantap.ifname='eth0 eth1'
+uci add_list network.br_phantap.ports='eth0'
+uci add_list network.br_phantap.ports='eth1'
 uci commit network
 /etc/init.d/network reload
 ```

files/etc/init.d/phantap

@@ -52,27 +52,32 @@ setup() {
 uci set system.ntp.enabled=0
 uci set system.ntp.server=''
 
-np=network.phantap
+nip=network.phantap
+ndp=network.br_phantap
 uci batch <<EOF
-set $np=interface
-set $np.type='bridge'
-set $np.proto='static'
-set $np.ipaddr='169.254.66.100'
-set $np.netmask='255.255.255.254'
-set $np.gateway='169.254.66.101'
-set $np.dns=''
-set $np.ifname=''
-set $np.ipv6='0'
+set $nip=interface
+set $nip.device='br-phantap'
+set $nip.proto='static'
+set $nip.ipaddr='169.254.66.100'
+set $nip.netmask='255.255.255.254'
+set $nip.gateway='169.254.66.101'
+set $nip.dns=''
+set $nip.ipv6='0'
+set $ndp=device
+set $ndp.type='bridge'
+set $ndp.name='br-phantap'
+set $ndp.ipv6='0'
 EOF
 echo "To finish phantap configuration, start by setting up wifi,"
 echo "then get the interface names from the device"
-echo "uci show network | grep ifname"
+echo "uci show network | grep -E 'device=|ports='"
 echo "If the interfaces are part of an interface already, remove them (assuming we are using a GL-AR150)"
-echo "uci delete network.lan.ifname"
-echo "uci delete network.wan.ifname"
-echo "uci delete network.wan6.ifname"
+echo "uci delete network.@device[0].ports"
+echo "uci delete network.wan.device"
+echo "uci delete network.wan6.device"
 echo "Add the interfaces to the phantap bridge and restart the network service (assuming we are using a GL-AR150)"
-echo "uci set network.phantap.ifname='eth0 eth1'"
+echo "uci add_list network.br_phantap.ports='eth0'"
+echo "uci add_list network.br_phantap.ports='eth1'"
 echo "uci commit network"
 echo "/etc/init.d/network reload"