Professional Firmware 20231202 for 3D Printers #1164
Replies: 40 comments 165 replies
-
|
It seems we need to wait for Special_Configurations release for Ender S1 firmware or can we use these release files for our devices ? Thanks. |
Beta Was this translation helpful? Give feedback.
-
|
Only the 422 STM32 version was tested enough to be released as precompiled firmware. Currently I don't have other hardware/boards to test other configurations. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you for reply and support. I've seen the demo release recently (https://github.com/mriscoc/Special_Configurations/releases/tag/demo), i hope tests will be completed as intended. |
Beta Was this translation helpful? Give feedback.
-
|
I INSTALLED THE VERSION Ender3V2-422-BLTUBL-MPC-20231217.bin |
Beta Was this translation helpful? Give feedback.
-
|
Could you be running into USB VBUS issues as described here? https://github.com/mriscoc/Ender3V2S1/wiki/Octoprint#important I use one of these to disconnect the USB V+ power line and I stopped having as many random failures due to comm between Octoprint and the printer: PortaPow USB Power Blocker... https://www.amazon.com/dp/B094FYL9QT Additionally, if you are using a long (>3ft/1m) USB cable, make certain it is away from 120/240v main power cables. I would still very rarely get a printer failure even with the power blocker; turns out I had a huge resistive+motor load (space heater) in the next room over, sharing that wall on the same electrical circuit, that was sending interference into the power lines as it kicked on. My USB cable was running immediately alongside the printer power cable. Note, this interference was slight enough that my UPS couldn't correct for it, but plenty enough to kill a print in progress. Once I figured out it was the heater cycling in the other room, I fixed the issue by physically separating the paths of the 120VAC and USB cables to the printer by about 18" and it never happened again. In short, the printer has basically no error correction capabilities on that serial connection - totally "old school" protocol. ANYTHING interfering on that USB line will mess up the communication and then either the printer or octoprint is going to stutter or completely crash out of the job. The less cable length, more shielding, and more distance from AC power lines you can manage = the better your stability will be. Oh, and if you didn't have these issues on stock FW, it could be due to stock FW using a lower data rate (128kbps), resulting in longer bitwise timing and more reliability under less than ideal conditions. |
Beta Was this translation helpful? Give feedback.
-
|
I tried every version available but nothing works. All the versions create the same problem. After homing the Z axis goes up an additional 7mm and stays there. When running the tramming wizard or the Auto Build Mesh the Z axis doesn't go down far enough to actually probe the bed. Stock Creality firmware works perfect. So thats what I'm going to run. It's an V4.2.7 board with a V2 Dacai display. |
Beta Was this translation helpful? Give feedback.
-
|
I was having similar issue on an E3. I had to turn off the z-axis software limit sensor. This way the probe would go down till it triggered instead of using the z-axis limit switch. For the 1st time you try this make sure you the probe is deployed and that it triggers and stops properly otherwise your nozzle will hit the bed.....I made this mistake and cut the power fast. |
Beta Was this translation helpful? Give feedback.
-
|
Marlin/src/HAL/STM32/../../inc/Changes.h:665:4: error: #error "FOLDER_SORTING is now SDSORT_FOLDERS." |
Beta Was this translation helpful? Give feedback.
-
|
Was able to build it. Had to change "Z_PROBE_OFFSET_RANGE_(MIN| |
Beta Was this translation helpful? Give feedback.
-
|
If you use old configuration files, might be missing new #defines, so it is better to use the new one and not patch the old ones. |
Beta Was this translation helpful? Give feedback.
-
|
Released "Special_Configurations" do not match released "Ender3V2S1". Files are all marked 06/11/23! I generated Ender3V2-422-MM-HomeOffs-IS-LA-MPC with both the "Special_Configurations DEMO" and the "Special_Configurations MASTER" version. First one works (after some editing - see bottom), second one crashed printer - Had to revert to Creality firmware to recover! Comparing "original configuration files" from each of the two "Special_Configurations" with released software show released "Ender3V2S1" configurations are closer to "Special_Configurations MASTER". "Special_Configurations MASTER" is the only version that contains the latest changes described in changes.h in "Ender3V2S1"; #elif defined(FOLDER_SORTING) |
Beta Was this translation helpful? Give feedback.
-
|
I was able to compile and get Special_Configurations to work on my E3V2 (v4.2.7 board) only by running the configuratator (the latest source code build, which as of right now was the Nov. 2023 release) and then merging necessary files with the September release of "Ender3V2S1". Will need to wait for "Special_Configurations" source code to match the current build of Ender3V2S1. Below was my generation json: |
Beta Was this translation helpful? Give feedback.
-
|
From GitHub download the current code status (click [CODE] and select "Local" and Download.zip) and unpack. Same with "Special_Configurations"... Unpack and run configurator. Move configs to "Marlin" folder and compile. Worked for my Ender3V2-422-MM-IS-LA-MPC. The "Release ZIPs" had some issues not long ago. |
Beta Was this translation helpful? Give feedback.
-
|
Only Precomp versions I see are for the 422 boards, where are the 427 versions? |
Beta Was this translation helpful? Give feedback.
-
|
Only the 422 STM32 version was tested enough to be released as precompiled firmware. Currently I don't have other hardware/boards to test other configurations. |
Beta Was this translation helpful? Give feedback.
-
|
Demo builds are now available here: https://github.com/mriscoc/Special_Configurations/releases/tag/demo |
Beta Was this translation helpful? Give feedback.
-
|
The 4.2.7 versions have been released |
Beta Was this translation helpful? Give feedback.
-
|
We need to donate more to Miguel so he can buy more test setups for future testing. 🎉 |
Beta Was this translation helpful? Give feedback.
-
|
I have always used the F1 precompiled versions in the past with no issue. When trying to load the |
Beta Was this translation helpful? Give feedback.
-
|
I am now releasing the Ender3S1-F1 and Ender3S1-F1-UBL-MPC versions. If a bug is found later, it will be added to a list of known bugs and fixes will be released in the next version, perhaps in late January. |
Beta Was this translation helpful? Give feedback.
-
|
Thanks @mriscoc - We will report if we find issues. |
Beta Was this translation helpful? Give feedback.
-
|
Thanks so much. |
Beta Was this translation helpful? Give feedback.
-
|
I have the Ender3V2-422 but I've upgraded to the Sprite Extruder Pro (SEP) and a CR Touch. I know this basically now makes my printer an Ender S1. So how do I get my CR touch to see the whole bed in conjunction with the SEP head. Currently the CRT identified the center of my bed about 20mm too far forward (due to the SEP dimensions) |
Beta Was this translation helpful? Give feedback.
-
|
@ImSadPanda Just use the Ender3V2 BLTUBL with T13 version and adjust your physical settings: https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides |
Beta Was this translation helpful? Give feedback.
-
|
I hate be the first asking, what stand AML2.0 for? |
Beta Was this translation helpful? Give feedback.
-
|
The Wiki will always be your friend: https://github.com/mriscoc/Ender3V2S1/wiki/Adaptive-Mesh-Leveling-(AML) |
Beta Was this translation helpful? Give feedback.
-
|
Hello, after instaling on ender 3v2 422 I have problem even tram a bed. Any help? |
Beta Was this translation helpful? Give feedback.
-
|
The probe cannot take height data if the bed is severy unleveled, try to first manually tram your bed. If you manually tramming your bed and the wizard continue to show error, could be a probe settings failure, please check with https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides |
Beta Was this translation helpful? Give feedback.
-
|
Hello thanks for answer. I have another problem.
|
Beta Was this translation helpful? Give feedback.
-
|
This is my Gcode G92 |
Beta Was this translation helpful? Give feedback.
-
|
Testing for FW: Ender3-422-BLT-CR10DSPLY-20231203 Out of the box BL bracket caused the probe to be lower than the nozzle so a new bracket was printed to move the BL up 6mm. This was out of range for the FW and the bracket was reprinted 3mm lower and homing succeeded. Not sure if that means a very tight window for probe to touch offset. Final Z offset came to 7.1mm. Homing still seems to have a bit of a glitch, Z only probes one time, flashes the BL and stops, no error and printing will continue. Not sure why no low speed home is attempted (high speed function?). 25 point bed leveling seems to work but most points double touch others don’t. Probe deploys and stows in different ways (randomly). Sometimes it deploys on Z raise, other times just before probing the next point. This was done just for testing before the Z offset was even entered. After setting Z offset (Very nice Z offset routine). Bed level function would not work after that. Probe would go to center and after clearly tripping the sensor would home everything and retry and fail again until finally halting printer. Turned off the BL high speed setting and homing and bed level worked as I perceived to be normal. Not sure high speed BL touch is ready for prime time or is worth it. Could not reproduce the bed level failure even after re enabling high speed BL. Still got random deploys on Z raise. Printing is working great, printed a couple test objects flawlessly, 10mm test cube and a bed level test. Definitely could live with this FW. |
Beta Was this translation helpful? Give feedback.
-
|
https://github.com/mriscoc/Ender3V2S1/wiki/3D-BLTouch |
Beta Was this translation helpful? Give feedback.
-
|
I tested the SKR Build, worked fine. First attempt at a print set off the filament runout, so I disabled then reenabled and it was fine after that... for an hour ;) |
Beta Was this translation helpful? Give feedback.
-
|
Please, elaborate the problem with the filament sensor, What is the physical configuration and settings used for the run-out sensor and post the exactly name of the firmware used in your test. Thank you for your report! |
Beta Was this translation helpful? Give feedback.
-
|
Wanted to report I've had success using |
Beta Was this translation helpful? Give feedback.
-
|
Hi, thanks for your report. |
Beta Was this translation helpful? Give feedback.
-
|
After a few successful, and a few failed prints, on Ender3V2-422-BLTUBL-MPC-20231202.bin on my Ender 3v2 with CRtouch, I discovered my stock extruder stepper motor was clicking/skipping during extrusion. So I ran a few extrusion calibration tests and confirmed it not reliably extruding the correct distance of filament even with the boden tube disconnected. With my finger on the stepper shaft I could feel it skipping a few times per revolution. For the sake of testing, I went back to Creality stock firmware v1.0.7 and the extruder stepper worked fine. I read that some steppers may require more voltage or something, but I wanted to report my experience in case it helps. Thanks! |
Beta Was this translation helpful? Give feedback.
-
|
Nevermind. It seems maybe i have a hardware issue with my extruder stepper... The missed steps/clicking is just less noticeable on the stock firmware lower extruder speeds, but still happens. I ordered a direct drive upgrade that hopefully fixes it. |
Beta Was this translation helpful? Give feedback.
-
|
I got my hardware issues sorted out and just wanted to follow up to confirm, Ender3V2-422-BLTUBL-MPC-20231202.bin is working great. Thanks again! |
Beta Was this translation helpful? Give feedback.
-
|
Compiled my own with Configurator and alla is good ender 3 v2 neo 4.2.2 tjc display. but i am trying to figure ut why Prusaslicer make so big thumbnail same python script on both.can only use 100x100/png now .but orcaslicer and superslicer is working with 200x200/PNG.and if i take thumbnail from orca and put in prusaslicer gcode it works . same stlfile gcode in prusa "thumbnail begin 200x200 8892" and in orca "thumbnail begin 200x200 3804" dont now why prusa make them so large, making me crazy arggg ;-) any suggestions |
Beta Was this translation helpful? Give feedback.
-
|
Maybe is the texture of the bed, remove or replace it with a black background. |
Beta Was this translation helpful? Give feedback.
-
|
Yes i think i figure it out ,I took ender3v2.svg from superslicer_2.5.59.3 and changed printer settings/bed shape/texture now i can use 200x200/PNG with prusaslicer_2.7.0 and Tjc display Mriscos 2023-12-04 . I love your firmware and am very happy .thanks for the hard work ! Mikael from sweden :-) |
Beta Was this translation helpful? Give feedback.
-
|
mayby it can help someone else |
Beta Was this translation helpful? Give feedback.
-
|
Hello, It possible help me? Verison 202309 worked perfectly. :)
|
Beta Was this translation helpful? Give feedback.
-
|
You need to post the exactly file name of the precompiled version installed. |
Beta Was this translation helpful? Give feedback.
-
|
Ender3V2-422-BLTUBL-MPC-20231202.bin on Ender3V2 Neo |
Beta Was this translation helpful? Give feedback.
-
|
The 422 version was updated but take note that TJC displays need a TJC firmware to be able to show mesh value data in the mesh viewer. |
Beta Was this translation helpful? Give feedback.
-
|
I'm ready to test CVLM version. 😇 Edit: And/or the F4 version(s), in general. 😎 |
Beta Was this translation helpful? Give feedback.
-
It seems to lose the mesh insets and physical bed size. Not sure what else. I'll test tomorrow when I'm in front of the printer again. |
Beta Was this translation helpful? Give feedback.
-
|
This version saves the mesh inset and mesh density along with the mesh values in a slot, so you need to save the data into a mesh slot. |
Beta Was this translation helpful? Give feedback.
-
This would then imply I need to update my config.gco to add a slot save. Interestingly enough, my config file loads these values in, but you are right that I didn't get to save a mesh and that resulted in those values being lost on reboot and demo kill. You may want to add a note to the documentation page for the config file to let everyone know that setting inset and density now requires more than a mere M500 to save it. Most of us are certainly used to a statically set mesh inset and density and may want to continue as such by using a single mesh slot (I only use one mesh slot, anyway). Edit: Also, for those of use with models like the Plus, the default insets and density are way off for the larger bed size, so every mesh slot we wish to save are going to need those set before a mesh can be done. This will need to happen somewhere along the path of setting up new slots the first time. I get the reasoning - to allow smaller faster meshes covering only the portion of the bed you intend to use, but it seems like more work for only a few use cases, since you probably don't need to be updating the mesh before every single print.
I can do that! Let me get on that tomorrow and I'll let you know. Also let me know when you have a new regular F4 to test. |
Beta Was this translation helpful? Give feedback.
-
|
I was unable to find what's the problem with The regular F4 version, so maybe was a glitch in my automatized toolchain, I re-compiled it without any important change and remove the limit, please test it: |
Beta Was this translation helpful? Give feedback.
-
|
After putting this file into a "STM32F4-UPDATE" folder. I only get a screen that has the Creality Logo and "Please wait until reboot". I might be doing something wrong. |
Beta Was this translation helpful? Give feedback.
-
|
Hello, I installed the Experimental-DEMO-Ender3V2-427-BLTUBL-T13-LA-MPC-20231203 version on Ender 3 Max Neo, disc 4.2.7, everything worked except linear advance, the printer stopped working after 1 hour of printing, printer killed was thrown. Is it possible that linear advance will not work with creality 4.2.7? |
Beta Was this translation helpful? Give feedback.
-
|
Thank you for your test. DEMO versions are restricted to 1 hour as explained in the DEMO release page. So, based on your test, that version is ready to be released? |
Beta Was this translation helpful? Give feedback.
-
|
The version works stably for me, but there is no reaction to the linear advance setting on the 4.2.7 disc, I tried adding gcode to the startup one on the printer in the settings and it didn't work, I don't know why... |
Beta Was this translation helpful? Give feedback.
-
|
I will release unrestricted 4.2.7 version without LA now, thank you for your tests. |
Beta Was this translation helpful? Give feedback.
-
|
You're doing a really great job :) |
Beta Was this translation helpful? Give feedback.
-
|
Hello, within the Assets I cannot find a version for the 3 S1. I have an STM32F401 board, which version shall I install from this release? Thx |
Beta Was this translation helpful? Give feedback.
-
|
Read carefully: https://github.com/mriscoc/Special_Configurations/releases/tag/demo |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
|
Hello folks, Im new here go easy on me lol. |
Beta Was this translation helpful? Give feedback.
-
|
What happens if you launch PID from the Advanced/Bed PID settings menu? |
Beta Was this translation helpful? Give feedback.
-
|
loud long beep until turn it off |
Beta Was this translation helpful? Give feedback.
-
|
Your bed thermistor is disconnected or faulty. |
Beta Was this translation helpful? Give feedback.
-
|
is that why perhaps when I send the code from pronterface its heats really high when trying to auto tune? What does not make any since is, ive been running the stock firmware since I bought it and never had these issues.I dont believe the very next day the bed thermistor died and not work. It just was finished my lastest prints and not 1 issue. |
Beta Was this translation helpful? Give feedback.
-
|
Sorry, I had to roll back FW to zap out a few last minute Christmas gifts and get some work done. haha What did I miss? What can I test? |
Beta Was this translation helpful? Give feedback.
-
|
Is it possible to get the Ender3V2-422-BLTUBL-MPC-20231217.bin updated to allow the x and Y axis max values in the "physical settings" to be 410x410mm for those of us that have the ender extender kit installed? |
Beta Was this translation helpful? Give feedback.
-
|
Follow the calibration guide https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides |
Beta Was this translation helpful? Give feedback.
-
|
Using Ender3V2-SKRME3V3-BLTUBL-MPC-20231218.bin the homing process would just move the y axis forward and never go back to the y endstop. Using Ender3V2-SKRME3V3-MM-20231218.bin I did not have the same issue. What could be causing this? |
Beta Was this translation helpful? Give feedback.
-
|
Maybe your bltouch is not connected correctly or this: #1186 |
Beta Was this translation helpful? Give feedback.
-
|
Sorry if I talk as if I know nothing. It's because I truly don't know what I am doing. My ender3v2 burnt the original mother board. I bought the skr mini 3v3 thinking direct drop in and go. Finding out not so much. Tried the bin file "Ender3v2-skrme3v3-bltubl-mpc-20231218.bin" flashed to the mini 3v3. Got the adapter cable for the dwin display. Flashed the display board. The firmware starts up but I get no icons on the main page and when I auto home the z homing doesn't function with the BL touch properly. I need help and I don't know how to compile a firmware my self. No coding knowledge. |
Beta Was this translation helpful? Give feedback.
-
|
The original ender 3v2 build with the original board I did use the adapter. But with the new bigtree tech mini skr 3v3, with the mriscoc build. The adapter says "media init fail" |
Beta Was this translation helpful? Give feedback.
-
|
I was just wondering if anyone had successfully used the SD card adapter with the ender 3v2 with the bigtreetech skr mini E3v3 with the mriscoc firmware. This firmware is already compiled, and I don't have the source to edit, and I tried to compile my own with the original creality marlin firmware with no success. I am not smart enough to compile my own firmware. I tried and failed every time. I am wondering if this mriscoc firmware has the option of using the SD card adapter. |
Beta Was this translation helpful? Give feedback.
-
|
Enable Advanced Menu / Media Update |
Beta Was this translation helpful? Give feedback.
-
|
Is this firmware able to update to a creality spider 3.0 pro hot end where it goes to higher hotend temps? |
Beta Was this translation helpful? Give feedback.
-
|
I got a bmg clone extruder, and I have changed the e steps up to match the 3:1 ratio change, but it goes so slow. I changed the max E speed up higher, but it still extrudes so slowly. What am I doing wrong? |
Beta Was this translation helpful? Give feedback.
-
|
Hello, I downloaded and installed the firmware perfectly! No known issues have surfaced from this but the only thing I truly wanted from this was to be able to change my hot ends max temperature to 300C and that doesn't seem to be working... Any fixes for this? I have all the prep work done to be able to use 300C responsibly and without damaging anything but I'm at a loss. |
Beta Was this translation helpful? Give feedback.
-
|
Send this |
Beta Was this translation helpful? Give feedback.
-
|
Beta Was this translation helpful? Give feedback.
-
|
Beta Was this translation helpful? Give feedback.
-
|
Thanks for your reply. Sounds great 👍🏻. I hope my suggestions are helpful. Your work is amazing, Muchas gracias Miguel.
|
Beta Was this translation helpful? Give feedback.
-
|
Hi,
|
Beta Was this translation helpful? Give feedback.
-
|
Is it possible to do a version of the firmware Ender3V2-422-BLTUBL-MPC where the max print temp for the hotend is 300c instead of 260c? I would change that setting the firmware myself, but i have no idea how to do any of that stuff, and i don't want to seriously mess something up. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you!
After reading all your instructions in wiki, each step performed as
described. I now understand that I was not using the T13 version. That has
solved my problem. Thank you for answering everyone's questions!
…On Wed, Jan 10, 2024 at 8:06 PM Miguel Risco-Castillo < ***@***.***> wrote:
@ImSadPanda <https://github.com/ImSadPanda> Just use the Ender3V2 with
T13 and adjust your physical settings:
https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides
—
Reply to this email directly, view it on GitHub
<#1164 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/A4UZCIUE2RLZHM4R5M5OWOLYN5JLFAVCNFSM6AAAAABADZTJWOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DAOBZGUZDG>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Hey Thank You for getting me the information I was needing.
I had a small other question that you might be able to answer. When I was
using you original (basic) Ender firmware 422... When I would perform a
filament change it would do it rapidly, Like crazy fast ejection, it would
dip the filament down into the hotend and then retract it at mach speed...
It was really cool, and super helpful for faster change outs. But sadly
with this T13 firmware I am back to slow-as-molassas with filament changes.
To be honest it feels even slower than the stock firmware did changes.
Any advice here?
Panda
…On Wed, Jan 10, 2024 at 8:06 PM Miguel Risco-Castillo < ***@***.***> wrote:
@ImSadPanda <https://github.com/ImSadPanda> Just use the Ender3V2 with
T13 and adjust your physical settings:
https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides
—
Reply to this email directly, view it on GitHub
<#1164 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/A4UZCIUE2RLZHM4R5M5OWOLYN5JLFAVCNFSM6AAAAABADZTJWOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DAOBZGUZDG>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Normal extruder and Sprite Pro extruder have different maximum speeds, you can increase the speed of Sprite Pro but there will be some noise due to the gears. |
Beta Was this translation helpful? Give feedback.
-
|
I installed the manual leveling version last week but just installed the CR Touch that came in the mail today so I'm trying to install the BL version but it won't flash. It just boots up normally. |
Beta Was this translation helpful? Give feedback.
-
|
Definitely stick to short filenames that are unique with every flash; I use date and a 2 or 3 char identifier: You may need to give the SD card a fresh format, too. The bootloader is very sensitive about the SD card. Even if the firmware, which is more forgiving, can read the card after boot up, the bootloader might be having issues reading the card. |
Beta Was this translation helpful? Give feedback.
-
|
I have similar issues with the original filenames. I regularly rename the firmware to a short filename too, to simply |
Beta Was this translation helpful? Give feedback.
-
|
Good plan, but add an incrementing number to the name, as the bootloader remembers the name of the last flashed files to preclude bootlooping and repeatedly flashing that same file. EDIT: Some boards do this, like the F4. I can't say for sure if all boards do this. |
Beta Was this translation helpful? Give feedback.
-
|
I first tried on my 4.2.7 board the file named by 231203.bin but that didn't work. I then tried V231203.bin and that worked. |
Beta Was this translation helpful? Give feedback.
-
|
Can confirm that renaming the file to |
Beta Was this translation helpful? Give feedback.
-
|
I'm now having 2 issues. 1) When I home X/Y my X is 3mm outside of the bed
area. I then used the Calibration Guides in wiki and adjusted the Physical
settings to show X Min = 3mm / Homed X / X trips the endstop like normal
but stays firmly against it / display now says X = 3, but nothing has
changed. I went extreme with this and set X min = 40/ Homed X / X triggered
endstop and stayed / display now says X=40 / X is still firmly up against
the endstop, No change.
When I start a print the wipe is off the board and just makes a mess. Large
print skirt also prints right off the board and everything is off center.
All prints are very far to the left of center. No adjustments seem to be
making a difference. Probe tests are all good however. (well they look ok
to me, but I'm new to the probe and maybe it's actually off as well, idk)
Issue 2) I ran a PLA preheat and went to my computer to load the print.
While I had my back to the printer my smoke alarm went off insider my
enclosure. I turned around to see the hotend smoking. I opened up the
enclosure to kill the power and noticed the hotend was at 280+ and rising!!
I killed the power. opened the windows and got the fire alarm to turn off.
My white PLA was dripping out of the hotend a burnt black! It freaked me
out and I was very glad I had taken one YouTubers advice to install that
smoke alarm!
I have not had a problem with Preheat since that event. idk what happened.
…On Wed, Jan 10, 2024 at 8:06 PM Miguel Risco-Castillo < ***@***.***> wrote:
@ImSadPanda <https://github.com/ImSadPanda> Just use the Ender3V2 with
T13 and adjust your physical settings:
https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides
—
Reply to this email directly, view it on GitHub
<#1164 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/A4UZCIUE2RLZHM4R5M5OWOLYN5JLFAVCNFSM6AAAAABADZTJWOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DAOBZGUZDG>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
If the X home position of the nozzle is outside of the bed, the X min is NEGATIVE, so the border of the bed is 0. |
Beta Was this translation helpful? Give feedback.
-
|
Hey Mriscoc,
Please disregard the X/Y homing issue. I found an adjustment in the Orca
slicer settings that compensated this concern. Thank you again for all your
help
Panda
On Tue, Jan 16, 2024 at 2:13 AM VerySadPanda ***@***.***>
wrote:
… I'm now having 2 issues. 1) When I home X/Y my X is 3mm outside of the bed
area. I then used the Calibration Guides in wiki and adjusted the Physical
settings to show X Min = 3mm / Homed X / X trips the endstop like normal
but stays firmly against it / display now says X = 3, but nothing has
changed. I went extreme with this and set X min = 40/ Homed X / X triggered
endstop and stayed / display now says X=40 / X is still firmly up against
the endstop, No change.
When I start a print the wipe is off the board and just makes a mess.
Large print skirt also prints right off the board and everything is off
center. All prints are very far to the left of center. No adjustments seem
to be making a difference. Probe tests are all good however. (well they
look ok to me, but I'm new to the probe and maybe it's actually off as
well, idk)
Issue 2) I ran a PLA preheat and went to my computer to load the print.
While I had my back to the printer my smoke alarm went off insider my
enclosure. I turned around to see the hotend smoking. I opened up the
enclosure to kill the power and noticed the hotend was at 280+ and rising!!
I killed the power. opened the windows and got the fire alarm to turn off.
My white PLA was dripping out of the hotend a burnt black! It freaked me
out and I was very glad I had taken one YouTubers advice to install that
smoke alarm!
I have not had a problem with Preheat since that event. idk what happened.
On Wed, Jan 10, 2024 at 8:06 PM Miguel Risco-Castillo <
***@***.***> wrote:
> @ImSadPanda <https://github.com/ImSadPanda> Just use the Ender3V2 with
> T13 and adjust your physical settings:
> https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides
>
> —
> Reply to this email directly, view it on GitHub
> <#1164 (reply in thread)>,
> or unsubscribe
> <https://github.com/notifications/unsubscribe-auth/A4UZCIUE2RLZHM4R5M5OWOLYN5JLFAVCNFSM6AAAAABADZTJWOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DAOBZGUZDG>
> .
> You are receiving this because you were mentioned.Message ID:
> ***@***.***>
>
|
Beta Was this translation helpful? Give feedback.
-
|
IS there already a new version that is compatible with the ender 3 v2 neo with tjc display and the gd32 chipset? |
Beta Was this translation helpful? Give feedback.
-
|
Use a TJC version for your board: https://github.com/mriscoc/Special_Configurations/releases/tag/tjc |
Beta Was this translation helpful? Give feedback.
-
|
Hello, I would need this latest release but without limited Y minimum value. I need to put -67 there and in the latest release its limited to -50.. |
Beta Was this translation helpful? Give feedback.
-
|
I never considered a value as large as that. You will need a custom build. |
Beta Was this translation helpful? Give feedback.
-
|
Yeah I have pretty unusual placement of bltouch sensor on the front of cooling duck. Custom build means the subscription to patreon and so on or is it possible to do myself with the souce code somehow? |
Beta Was this translation helpful? Give feedback.
-
|
Of course you can build it yourself. So you need to change the probe offsets, no the Y minimum position. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you for programming this all. I am by far no expert. Via looking to youtube a lot and reading a lot i managed to install and use Ender3V2-422-BLTUBL-MPC-20231217.bin. |
Beta Was this translation helpful? Give feedback.
and others
-
ANNIVERSARY 2023 AML 2.0 Edition
What's new in this release
From Marlin Bugfix
To incentive the test and the feedback of the firmware by the community I'm releasing demo firmwares compiled using the current sources: https://github.com/mriscoc/Special_Configurations/releases/tag/demo please be sure to read the demo release notes.
Community links
Donations
Thank you for your support, I receive donations through Patreon and Paypal
Beta Was this translation helpful? Give feedback.
All reactions