cxadc is an alternative Linux driver for the Conexant CX2388x series of video decoder/encoder chips used on many PCI TV tuner and capture cards.
The new driver configures the CX2388x to capture in its raw output mode in 8-bit or 16-bit unsigned samples from the video input ports, allowing these cards to be used as a low-cost 28-54mhz 10bit ADC for SDR and similar applications.
Note
CX23885-xx & CX23888-xx are incompatible chips, however the CX25800 is a compatible chip.
Today the cheap PCIe (with 1x bridge chip) capture card market uses these chips at 16-35USD prices per card, directly from China.
The regular cx88 driver in Linux provides support for capturing composite video, digital video, audio and the other normal features of these chips.
Warning
You shouldn't load both drivers at the same time.
There is now a wiki about the cards variants and helpful information on modifications cabling and amplification.
Links to buy a CX Card:
- Current CX White CX25800 Card Order Links Link 1 Link 2 Link 3 (16~30 USD) (Recommended as it has the better CX25800 IC)
- Blue Variant
Note 00: While Mhz is used and is accurate due to the crystal used, in reality, it should be called MSPS (million samples per second) as the actual effective sampled is half the Mhz number of the defined crystal/clock rate.
Note 01: The CX chip variant with the least self-noise is the CX25800, mostly found on the White Variation card; most clean captures are at 6dB off, and Digital Gain at 0-10 with external amplification and or proper impedance matching.
Note 02: For reliable 40mhz 8-bit & 20mhz 16-bit samples, it is recommended to replace the stock crystal with a ABLS2-40.000MHZ-D4YF-T or equivalent fundamental crystal.
For the full list of working crystal replacements, check the wiki page here!
Note 03: Asmedia PCI to PCIe 1x bridge chips may have support issues on some older PCH chipsets based on Intel 3rd gen; for example, white cards use ITE chips which might not have said issue.
Note 04: Added cooling can provide additional stability, more so with 40-54mhz crystal mods, but within 10° Celsius of room temperature is always preferable for silicone hardware. Currently, only 40-54mhz crystal mods have been broadly viable in testing for current white PCIe cards.
Note 05: For crystals over 54mhz: it might be possible to use higher crystals with self-temperature regulated isolated chamber models, but this is still to have proper testing.
Note 06: While the term Mhz is used and is hardware accurate, to be clear with Nyquist sampling the crystal frequency should be noted as the MSPS or million samples per second rating, the number is always halved to equal its effective bandwidth of whatever its sampling i.e 28mhz is 28msps with 14mhz of bandwidth and so on you want a 2:1 ratio or higher of whatever your capturing to correctly sample it.
Note 07: When using lower-end older systems (Pentium 4 and before era), if there are not enough system resources, you may have dropped samples, this also applies to any use of SoX or FLAC in real-time.
Update your package manager
sudo apt update
Install build essentials
sudo apt install build-essential
Install Linux Headers
sudo apt install linux-headers-generic
Install PV for real-time monitoring of the runtime & datarate output:
sudo apt install pv
Install Sox key for manipulating data in real-time or more usefully after captures:
sudo apt install sox
Install FFmpeg (If you don't already have it!)
sudo apt install ffmpeg
Install FLAC (If you don't already have it!)
sudo apt install flac
As above, but install raspberrypi-kernel-headers instead of linux-headers-generic,
and then add the following to the end of /boot/firmware/config.txt:
[all]
dtoverlay=pcie-32bit-dma
Pull the driver via terminal
Open a terminal window and git clone the repository:
git clone https://github.com/happycube/cxadc-linux3 cxadc
For offline install simply, click Code on the GitHub page and then download the zip.
Move the zip to your home directory into a folder called cxadc and extract the files.
Afterward, open a terminal in the said directory and continue below.
You can then use git pull inside the directory to update later and then re-build the driver with the steps below again or likewise manually re-download the files.
If not already inside of the CXADC directory
cd cxadc
Build and install the out-of-tree module:
make && sudo make modules_install && sudo depmod -a
If you see the following error, ignore it:
At main.c:160:
- SSL error:02001002:system library:fopen:No such file or directory: ../crypto/bio/bss_file.c:69
- SSL error:2006D080:BIO routines:BIO_new_file:no such file: ../crypto/bio/bss_file.c:76
sign-file: certs/signing_key.pem: No such file or directory
Warning: modules_install: missing 'System.map' file. Skipping depmod.
This error just means the module could not be signed. It will still be installed.
Install configuration files:
sudo cp cxadc.rules /etc/udev/rules.d
sudo cp cxadc.conf /etc/modprobe.d
Now reboot and the modules will be loaded automatically. The device node will
be called /dev/cxadc0. The default cx88 driver will be blacklisted by cxadc.conf.
Module parameters can also be configured in that file.
If there is an issue just re-load the CXADC module from the install directory via terminal
sudo rmmod cxadc
make
sudo make modules_install
sudo depmod -a
depmod -a enables auto load on start-up
You can then install scripted commands to help operate and verify your configuration.
Check the utils folder and the associated README for quicker and more simplified commands.
To enable short system wide commands, first change into the utils directory from the cxadc source folder:
cd utils
Then install the system links with:
sudo ./inst_scripts
Warning
Secure boot is the most common issue with many PCI/PCIe devices on Linux very much so video class devices such as BMD SDI hardware.
If the kernal is updated, the driver will need a re-install unless DKMS is setup.
If you see this error:
arch/x86/Makefile:142: CONFIG_X86_X32 enabled but no binutils support
INSTALL /lib/modules/5.15.0-92-generic/extra/cxadc.ko
SIGN /lib/modules/5.15.0-92-generic/extra/cxadc.ko
DEPMOD /lib/modules/5.15.0-92-generic
Warning: modules_install: missing 'System.map' file. Skipping depmod.
make[1]: Leaving directory '/usr/src/linux-headers-5.15.0-92-generic'
Caution
Ensure secure boot is disabled before doing anything else.
Try Install Binutils
apt install binutils
If issues with binutills persists just use a different Kernel like Xanmod has been tested as a fix to the issue.
Most of these parameters (except latency) can be changed using sysfs
after the module has been loaded. Re-opening the device will update the
CX2388x's registers. If you wish to be able to change module parameters
as a regular users (e.g. without sudo), you need to run the command:
sudo usermod -a -G video YourUbuntuUserName
To change configuration open the terminal and use the following command to change driver config settings.
Caution
Configuration will reset on every re-boot of the system, save your config and paste the commands at every start-up ready for capture.
Note
You can use cxvalues to check your current configuration state at anytime globally on the terminal.
X = Number Setting i.e 0 1 2 3 etc
Y = Parameter setting i.e vmux, level etc
echo X >/sys/class/cxadc/cxadc0/device/parameters/Y
Example: echo 1 >/sys/class/cxadc/cxadc0/device/parameters/vmux
Warning
Also see the utils folders for scripts to manipulate these values; sudo will be required unless you add your local user to the video group as mentioned above.
In single card capture mode this is cat /dev/cxadc0
With multi card this will be cat /dev/cxadc1 and so on for card 2 and 3 etc
Same for parameters
sudo echo 1 >/sys/class/cxadc/cxadc0/device/parameters/vmux
This changes to
sudo echo 1 >/sys/class/cxadc/cxadc1/device/parameters/vmux
This can go up to 256, but real world use we don't expect more then 8-16 per system.
Check the Wiki for the optimal way to connect your card type!
A typical TV card has a tuner, a composite input with RCA or BNC ports and S-Video input, tied to three of these inputs; you may need to experiment with inputs. The quickest way is to attach a video signal and see a white flash on signal hook-up, and change vmux until you get something.
Create a video preview of signal. Depending on the RF signal type, you will get an unstable video or just a white flash on cable connection.
(Using video_size values to give approximately the correct resolution for the default 28.64 Mhz sample rate)
PAL:
sudo ffplay -hide_banner -async 1 -f rawvideo -pixel_format gray8 -video_size 1832x625 -i /dev/cxadc0 -vf scale=1135x625,eq=gamma=0.5:contrast=1.5
NTSC:
sudo ffplay -hide_banner -async 1 -f rawvideo -pixel_format gray8 -video_size 1820x525 -i /dev/cxadc0 -vf scale=910x525,eq=gamma=0.5:contrast=1.5
Some TV cards (e.g. the PixelView PlayTV Pro Ultra) have an external multiplexer attached to the CX2388x's GPIO pins to select an audio channel. If your card has one, you can select the input using this parameter.
On the PlayTV Pro Ultra:
audsel=0: tuner tv audio out?audsel=1: silence?audsel=2: FM stereo tuner out?audsel=3: audio in to audio out
The PCI latency timer value for the device.
Enables or disables a default 6db gain applied to the input signal (Disabling this can result in cleaner capture but may require an external amplifier)
1 = On
0 = Off
The fixed digital gain to be applied by the CX2388x
(INT_VGA_VAL in the datasheet).
Adjust to minimise clipping; ./leveladj will do this
for you automatically.
To change the card witch add the -h flag followed by the card so ./leveladj -h 1 for card 2 for example.
By default, cxadc captures at a rate of 8 x fsc (8 * 315 / 88 Mhz, approximately 28.6 MHz)
tenxfsc - Sets sampling rate of the ADC based on the crystal's native frequency
0 = Native crystal frequency i.e 28MHz (default), 40, 50, 54, (Modified etc)
1 = Native crystal frequency times 1.25
2 = Native crystal frequency times ~1.4
With the Stock 28Mhz Crystal the modes are the following:
0 = 28.6 MHz 8bit
1 = 35.8 MHz 8bit
2 = 40 MHz 8bit
Note!
40Mhz 8-bit & 20Mhz 16-bit modes have a very rare chance of working on stock non-modified cards, with the stock 28Mhz crystal. It's recommended to physically replace the stock crystal with an ABLS2-40.000MHZ-D4YF-T, to achieve said sample rate capture ability and lower noise.
Alternatively, enter 2 digit values (like 20), that will then be
multiplied by 1,000,000 (so 20 = 20,000,000sps), with the caveat
that the lowest possible rate is a little more than 1/3 the actual
HW Crystal rate (HW crystal / 40 * 14). For stock 28.6mhz crystal,
this is about 10,022,728sps.
For a 40mhz crystal card, the lowest rate will be 14,000,000sps. The highest rate is capped at the 10fsc rate, or: HW crystal / 8 * 10.
Full-range sample values can also be entered: 14318181 for instance. Again, the caveat is that the lowest possible rate is: HW crystal / 40 * 14 and the highest allowed rate is: HW crystal / 8 * 10.
Values outside the range will be converted to the lowest / highest value appropriately. Higher rates may work, with the max rate depending on individual card and cooling, but can cause system crash for others, so are prevented by the driver code (increase at your own risk).
By default, cxadc captures unsigned 8-bit samples.
In mode 1, unsigned 16-bit mode, the data is resampled (down-converted) by 50%
0 = 8xFsc 8-bit data mode (Raw Unsigned Data)
1 = 4xFsc 16-bit data mode (Filtered Vertical Blanking Interval Data)
When in 16bit sample modes, change to the following:
14.3 MHz 16-bit - Stock Card
17.9 MHz 16-bit - Stock Card
20 MHz 16-bit - Stock Card
The Mhz of the physical XTAL crystal on your CX Card. The stock crystal is usually a 28636363 (28.6Mhz) fundamental type, but a 40mhz replacement crystal is easily available and crystals as high as 54mhz have been shown to work (with extra cooling required above 40mhz).
This value is ONLY used to compute the sample rates entered for the tenxfsc parameters other than 0, 1, 2.
This option allows you to manually adjust DC center offset or the centering of the RF signal you wish to capture.
Manual calculation: If the "highest" and "lowest" values returned are equidistant from 0 and 255 respectively, it's cantered.
Use leveladj to obtain level and centring information
./leveladj
Example:
low 121 high 133 clipped 0 nsamp 2097152
121-121=0 133+121 = 254 = centred, but: low
110 high 119 clipped 0 nsamp 2097152
110-110=0 119+110 = 229 = not centred.
You can visually adjust this with a handy GNURadio Script
Connect a live or playing signal to the input you've selected, and run leveladj to adjust the gain automatically:
./leveladj
To use this on multiple different cards
./leveladj -d 1 (1 means for device 2/3/4 and so on device 0 is assumed when -d is not used)
You can manually set a fixed gain setting after centering the signal with
sudo echo 0 >/sys/class/cxadc/cxadc0/device/parameters/level - Internal Gain (0~31)
sudo echo 0 >/sys/class/cxadc/cxadc0/device/parameters/sixdb - Digital Gain Boost (1 On / 0 Off)
Open a terminal in the directory you wish to write the data to, and use the following example command to capture 10 seconds of test samples.
timeout 10s cat /dev/cxadc0 |pv > CX_Card_28msps_8-bit.u8
Press Ctrl+C to copy then Ctrl+P to past the command use <+> to move edit position on the command line to edit the name or command and Enter to run the command.
cat is the default due to user issues with dd
To use the PV argument that enables data rate/runtime readout, modify the command command with |pv >
It will look like this when in use:
cat /dev/cxadc0 |pv > CX_Card_28msps_8-bit.u8
0:00:04 [38.1MiB/s] [ <=>
Ctrl+C Will kill the current process, use this to stop the capture manually.
timeout 10s defines the capture duration of 10 seconds, this can be defined in hours minutes or seconds if a timeout duration is not set it will capture until storage space runs out or is stopped manually.
sox -r 28636363 etc can be used to resample to the sample rate specified, whereas cat/dd will just do whatever has been pre-defined by the parameters set above.
Note: For use with the decode projects, filetypes .u8 for 8-bit & .u16 for 16-bit samples are used instead of .raw extension.
This allows the software to correctly detect the data and use it for decoding or flac compression and renaming to .vhs/.svhs etc.
Optional but not optimal due to risk of dropped samples even with high-end hardware etc, on the fly FLAC compressed captures are possible with the following commands; edit rates as needed.
8-bit Mode (Stock 28.6 MSPS)
cat /dev/cxadc0 | flac --fast -16 --sample-rate=28636 --sign=unsigned --channels=1 --endian=little --bps=8 --blocksize=65535 --lax -f - -o media-name-28msps-8bit-cx-card.flac
16-bit Mode (Stock 17.8 MSPS)
cat /dev/cxadc0 | flac --fast -16 --sample-rate=17898 --sign=unsigned --channels=1 --endian=little --bps=16 --blocksize=65535 --lax -f - -o media-name-17.8msps-16bit-cx-card.flac
Secure boot can cause issues.
Kernel updates will break the driver and require a full re-installation, unless DKMS is setup.
rules.config - Inside this file are your defined base settings every time the driver loads
cxadc was originally written by Hew How Chee ([email protected]). See SDR using a CX2388x TV+FM card for more details.
- added support for i2c, use
i2c.cto tune - set registers to lower gain
- set registers so that no signal is nearer to sample value 128
- added
vmuxandaudselas params during driver loading (for 2nd IF hardware modification, load driver usingvmux=2). By defaultaudsel=2is to route tv tuner audio signal to audio out of TV card,vmux=1to use the signal from video in of tv card.
- change code to compile and run in kernel 2.6.18 (Fedora Core 6) for Intel 32 bit single processor only
- clean up mess in version 0.2 code
This version has been retargeted for Ubuntu 13.10 Linux 3.11 by Chad Page ([email protected]).
While still a mess, the driver has been simplified a bit. Data is now read
using standard read() semantics, so no capture program is needed like the original
version.
For the first time, it also runs on 64-bit Linux, and seems to be OK under SMP.
- Update to work with Linux 5.1; older versions should still work.
- Tidy up the code to get rid of most of the warnings from checkpatch, and bring it closer in style to the normal cx88 driver.
- Make
audseloptional. - Don't allow
/dev/cxadcto be opened multiple times. - When unloading cxadc, reset the AGC registers to their default values. as cx88 expects. This lets you switch between cxadc and cx88 without rebooting.
Information Additions Documentation Cleanup by Harry Munday ([email protected])
- Change 10bit to the correct 16bit as that's what's stated in RAW16 under the datasheet and that's what the actual samples are in format-wise.
- Cleaned up and added examples for adjusting module parameters and basic real-time readout information.
- Added notations of ABLS2-40.000MHZ-D4YF-T a drop-in replacement crystal that adds 40mhz ability at low cost for current market PCIe cards.
- Added documentation for sixdb mode selection.
- Added links to find current CX cards
- Added issues that have been found
- Added crystal list of working replacements
New additions by Tony Anderson ([email protected])
- Fixed ./leveladj script from re-setting module parameters
- Added new command scripts
- Added new level adjustment tool cxlvlcavdd
- Added dedicated readme for new scripts and future tools
- Documentation Cleanup
- More utils additons
- Added cxlevel (utils/README.md)
- Added cxfreq (utils/README.md)
- Added cxvalues shows the current configuration.
- Added fortycryst 0 for no, 1 for yes, and then added sample rates 11-27 (14-27 on 40cryst)
- Added warning messages for high & low gain states
New multi-card support added by Adam R
- Multi card support up to 256 cards per system
- Individual card settings support
- Documentation & Scripts updated
Clockgen Mod Established
- Software defined 20/28.6/40/50msps modes
- Shared clock source synchronised capture
- Raspberry Pi 4 & 5 support added by Alistair Buxton