MHP30 Soldering/Reflow Temperature Profile

Documentation/GettingStarted.md

@@ -42,7 +42,7 @@ This OLED screen features burn-in protection; if no buttons or movement have bee
 
 Additionally to the two icons shown, there are two "hidden" actions that can be performed on this menu.
 
-If you press and hold the button near the tip (`+/A`), this enters the temperature adjustment screen. Normally this is not required; but if you would like to adjust the set temperature _before_ the tip starts to heat, this can be useful.
+On devices that do not support profile mode, if you press and hold the button near the tip (`+/A`), this enters the temperature adjustment screen. Normally this is not required; but if you would like to adjust the set temperature _before_ the tip starts to heat, this can be useful.
 
 If you press and hold the button near the rear of the iron (`-/B`), it will take you into the [debug menu](https://ralim.github.io/IronOS/DebugMenu/).
 
@@ -74,6 +74,23 @@ Pinecil has an unpopulated footprint (U14) for a hall effect sensor (Si7210-B-00
 
 If, after entering sleep mode, the iron still does not see movement for a much longer time (default=10 minutes); it will shut down and return to the home screen.
 
+## Profile Mode (MHP30 only)
+
+On devices that support it, a long press on `(+/A)` takes you into profile mode, which initiates the profile selected in the relevant settings.
+
+Profile mode plays out as follows:
+
+1. Check if the temperature is below 55C. If not, you will get a warning and cannot enter profile mode.
+2. Preheat by raising the target temperature to the configured preheat temperature with the configured preheat speed.
+3. Wait for the device to reach the preheat temperature.
+4. Gradually move the target temperature to the configured end temperature of the first phase over the configured duration. 
+5. Wait for the device to reach the end temperature. 
+6. Repeat steps 4 and 5 for the next phases until there are no more phases configured.
+7. Cool down by lowering the target temperature to 0 with the configured cooldown speed. 
+8. Once the temperature is below 55C, sound the buzzer (if available) and exit profile mode. 
+
+You can manually exit profile mode manually in the same way as the soldering mode, by pressing and holding the rear button or pressing both buttons at once.
+
 ## Settings Menu
 
 The settings menu is the most evolving aspect of the firmware, so each option is not documented here. However, do not panic, as every menu option has an on-screen description so you don't _need_ to come back here to figure them all out.

Documentation/Menu.md

@@ -9,6 +9,12 @@ In this mode the iron works as you would expect, pressing either button will tak
 - Pressing both buttons or holding the rear button (`-/B`) will exit Soldering Mode.
 - Holding the front button (`+/A`) will enter [Boost mode](https://ralim.github.io/IronOS/Menu/#boost-mode) (if enabled).
 
+## Profile mode (MHP30 only)
+
+In this mode, accessible by long pressing `(+/A)`, the configured profile will be initiated.
+- You cannot adjust the temperature or enter boost mode.
+- Pressing both buttons or holding the rear button (`-/B`) will exit Profile Mode as well.
+
 ## Settings mode
 
 This mode allows you to cycle through all the options and set custom values.

Translations/make_translation.py

@@ -66,6 +66,29 @@ def read_translation(json_root: Union[str, Path], lang_code: str) -> dict:
     return lang
 
 
+def filter_translation(lang: dict, defs: dict, macros: frozenset):
+    def check_excluded(record):
+        if "include" in record and not any(m in macros for m in record["include"]):
+            return True
+
+        if "exclude" in record and any(m in macros for m in record["exclude"]):
+            return True
+
+        return False
+
+    for category in ("menuOptions", "menuGroups"):
+        for index, record in enumerate(defs[category]):
+            if check_excluded(record):
+                lang[category][record["id"]]["displayText"] = ""
+                lang[category][record["id"]]["description"] = ""
+
+    for index, record in enumerate(defs["messagesWarn"]):
+        if check_excluded(record):
+            lang["messagesWarn"][record["id"]]["message"] = ""
+
+    return lang
+
+
 def validate_langcode_matches_content(filename: str, content: dict) -> None:
     # Extract lang code from file name
     lang_code = filename[12:-5].upper()
@@ -101,6 +124,8 @@ def get_constants() -> List[Tuple[str, str]]:
         ("SmallSymbolSpace", " "),
         ("LargeSymbolDot", "."),
         ("SmallSymbolDot", "."),
+        ("SmallSymbolSlash", "/"),
+        ("SmallSymbolColon", ":"),
         ("LargeSymbolDegC", "C"),
         ("SmallSymbolDegC", "C"),
         ("LargeSymbolDegF", "F"),
@@ -250,7 +275,6 @@ def get_letter_counts(defs: dict, lang: dict, build_version: str) -> Dict:
     # collapse all strings down into the composite letters and store totals for these
     # Doing this seperately for small and big font
     def sort_and_count(list_in: List[str]):
-
         symbol_counts: dict[str, int] = {}
         for line in list_in:
             line = line.replace("\n", "").replace("\r", "")
@@ -439,7 +463,6 @@ class FontMapsPerFont:
 def get_font_map_per_font(
     text_list_small_font: List[str], text_list_large_font: List[str]
 ) -> FontMapsPerFont:
-
     pending_small_symbols = set(text_list_small_font)
     pending_large_symbols = set(text_list_large_font)
 
@@ -1029,7 +1052,6 @@ def get_translation_strings_and_indices_text(
     large_font_symbol_conversion_table: Dict[str, bytes],
     suffix: str = "",
 ) -> str:
-
     # For all strings; we want to convert them to their byte encoded form (using font index lookups)
     # Then we want to sort by their reversed format to see if we can remove any duplicates by combining the tails (last n bytes;n>0)
     # Finally we look for any that are contained inside one another, and if they are we update them to point to this
@@ -1118,7 +1140,6 @@ def encode_string_and_add(
     translation_strings_text = "  /* .strings = */ {\n"
 
     for i, encoded_bytes in enumerate(byte_encoded_strings):
-
         if i > 0:
             translation_strings_text += ' "\\0"\n'
 
@@ -1285,6 +1306,13 @@ def parse_args() -> argparse.Namespace:
         required=False,
         dest="compress_font",
     )
+    parser.add_argument(
+        "--macros",
+        help="Extracted macros to filter translation strings by",
+        type=argparse.FileType("r"),
+        required=True,
+        dest="macros",
+    )
     parser.add_argument(
         "--output", "-o", help="Target file", type=argparse.FileType("w"), required=True
     )
@@ -1305,6 +1333,12 @@ def main() -> None:
         logging.error("error: Both --output-pickled and --input-pickled are specified")
         sys.exit(1)
 
+    macros = (
+        frozenset(re.findall(r"#define ([^ ]+)", args.macros.read()))
+        if args.macros
+        else frozenset()
+    )
+
     language_data: LanguageData
     if args.input_pickled:
         logging.info(f"Reading pickled language data from {args.input_pickled.name}...")
@@ -1329,11 +1363,13 @@ def main() -> None:
 
         defs_ = load_json(os.path.join(json_dir, "translations_definitions.json"))
         if len(args.languageCodes) == 1:
-            lang_ = read_translation(json_dir, args.languageCodes[0])
+            lang_ = filter_translation(
+                read_translation(json_dir, args.languageCodes[0]), defs_, macros
+            )
             language_data = prepare_language(lang_, defs_, build_version)
         else:
             langs_ = [
-                read_translation(json_dir, lang_code)
+                filter_translation(read_translation(json_dir, lang_code), defs_, macros)
                 for lang_code in args.languageCodes
             ]
             language_data = prepare_languages(langs_, defs_, build_version)

Translations/translation_BE.json

@@ -60,8 +60,17 @@
         "OffString": {
             "message": "Выкл."
         },
+        "ProfilePreheatString": {
+            "message": "Preheat\n"
+        },
+        "ProfileCooldownString": {
+            "message": "Cooldown\n"
+        },
         "DeviceFailedValidationWarning": {
             "message": "Ваша прылада, хутчэй за ўсё, падробка!"
+        },
+        "TooHotToStartProfileWarning": {
+            "message": "Too hot to\nstart profile"
         }
     },
     "characters": {
@@ -143,6 +152,62 @@
             "displayText": "Дазволіць\nблок. кнопак",
             "description": "Пры рабоце падоўжаны націск дзьвух кнопак блакуе іх (А=Адключана | Т=Толькі турба | П=Поўная блакіроўка)"
         },
+        "ProfilePhases": {
+            "displayText": "Profile\nPhases",
+            "description": "Number of phases in profile mode"
+        },
+        "ProfilePreheatTemp": {
+            "displayText": "Preheat\nTemp",
+            "description": "Preheat to this temperature at the start of profile mode"
+        },
+        "ProfilePreheatSpeed": {
+            "displayText": "Preheat\nSpeed",
+            "description": "Preheat at this rate (degrees per second)"
+        },
+        "ProfilePhase1Temp": {
+            "displayText": "Phase 1\nTemp",
+            "description": "Target temperature for the end of this phase"
+        },
+        "ProfilePhase1Duration": {
+            "displayText": "Phase 1\nDuration",
+            "description": "Target duration of this phase (seconds)"
+        },
+        "ProfilePhase2Temp": {
+            "displayText": "Phase 2\nTemp",
+            "description": ""
+        },
+        "ProfilePhase2Duration": {
+            "displayText": "Phase 2\nDuration",
+            "description": ""
+        },
+        "ProfilePhase3Temp": {
+            "displayText": "Phase 3\nTemp",
+            "description": ""
+        },
+        "ProfilePhase3Duration": {
+            "displayText": "Phase 3\nDuration",
+            "description": ""
+        },
+        "ProfilePhase4Temp": {
+            "displayText": "Phase 4\nTemp",
+            "description": ""
+        },
+        "ProfilePhase4Duration": {
+            "displayText": "Phase 4\nDuration",
+            "description": ""
+        },
+        "ProfilePhase5Temp": {
+            "displayText": "Phase 5\nTemp",
+            "description": ""
+        },
+        "ProfilePhase5Duration": {
+            "displayText": "Phase 5\nDuration",
+            "description": ""
+        },
+        "ProfileCooldownSpeed": {
+            "displayText": "Cooldown\nSpeed",
+            "description": "Cooldown at this rate at the end of profile mode (degrees per second)"
+        },
         "MotionSensitivity": {
             "displayText": "Адчувальнасць\nакселерометра",
             "description": "Адчувальнасць акселерометра (0=Выкл. | 1=Мін. | ... | 9=Макс.)"

Translations/translation_BG.json

@@ -60,8 +60,17 @@
         "OffString": {
             "message": "Изкл."
         },
+        "ProfilePreheatString": {
+            "message": "Preheat\n"
+        },
+        "ProfileCooldownString": {
+            "message": "Cooldown\n"
+        },
         "DeviceFailedValidationWarning": {
             "message": "Your device is most likely a counterfeit!"
+        },
+        "TooHotToStartProfileWarning": {
+            "message": "Too hot to\nstart profile"
         }
     },
     "characters": {
@@ -143,6 +152,62 @@
             "displayText": "Allow locking\nbuttons",
             "description": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)"
         },
+        "ProfilePhases": {
+            "displayText": "Profile\nPhases",
+            "description": "Number of phases in profile mode"
+        },
+        "ProfilePreheatTemp": {
+            "displayText": "Preheat\nTemp",
+            "description": "Preheat to this temperature at the start of profile mode"
+        },
+        "ProfilePreheatSpeed": {
+            "displayText": "Preheat\nSpeed",
+            "description": "Preheat at this rate (degrees per second)"
+        },
+        "ProfilePhase1Temp": {
+            "displayText": "Phase 1\nTemp",
+            "description": "Target temperature for the end of this phase"
+        },
+        "ProfilePhase1Duration": {
+            "displayText": "Phase 1\nDuration",
+            "description": "Target duration of this phase (seconds)"
+        },
+        "ProfilePhase2Temp": {
+            "displayText": "Phase 2\nTemp",
+            "description": ""
+        },
+        "ProfilePhase2Duration": {
+            "displayText": "Phase 2\nDuration",
+            "description": ""
+        },
+        "ProfilePhase3Temp": {
+            "displayText": "Phase 3\nTemp",
+            "description": ""
+        },
+        "ProfilePhase3Duration": {
+            "displayText": "Phase 3\nDuration",
+            "description": ""
+        },
+        "ProfilePhase4Temp": {
+            "displayText": "Phase 4\nTemp",
+            "description": ""
+        },
+        "ProfilePhase4Duration": {
+            "displayText": "Phase 4\nDuration",
+            "description": ""
+        },
+        "ProfilePhase5Temp": {
+            "displayText": "Phase 5\nTemp",
+            "description": ""
+        },
+        "ProfilePhase5Duration": {
+            "displayText": "Phase 5\nDuration",
+            "description": ""
+        },
+        "ProfileCooldownSpeed": {
+            "displayText": "Cooldown\nSpeed",
+            "description": "Cooldown at this rate at the end of profile mode (degrees per second)"
+        },
         "MotionSensitivity": {
             "displayText": "Усещане\nза движение",
             "description": "Усещане за движение (0=Изключено | 1=Слабо | ... | 9=Силно)"