Bootup logo settings (#1241)

Adds ability to adjust the time shown for the bootup logo.

Documentation/Settings.md

@@ -109,15 +109,15 @@ On device help text:
 
 Temperature used in "boost mode"
 
-### Setting: Heat on power up
+### Setting: Start-up behavior
 
 When the device powers up, should it enter into a special mode. These settings set it to either start into soldering mode, sleeping mode or auto mode (Enters into soldering mode on the first movement).
 
 On device help text:
 
 O=off | S=soldering temp | Z=standby at sleep temp until moved | R=standby without heating until moved
 
-### Setting: Cooldown blink
+### Setting: Cooldown flashing
 
 If the idle screen should blink the tip temperature for attention while the tip is over 50°C. Intended as a 'tip is still hot' warning.
 
@@ -133,13 +133,13 @@ On device help text:
 
 Start tip temperature offset calibration
 
-### Setting: Factory reset?
+### Setting: Restore factory settings?
 
 Resets all settings and calibrations to factory defaults. Does NOT erase custom user boot up logo's.
 
 On device help text:
 
-Reset settings to default
+Reset all settings to default
 
 ### Setting: Calibrate input voltage?
 
@@ -189,7 +189,7 @@ On device help text:
 
 Maximum power the iron can use (W=watt)
 
-### Setting: Reverse + - keys
+### Setting: Swap + - keys
 
 Swaps which button increments and decrements on temperature change screens.
 
@@ -285,7 +285,7 @@ On device help text:
 
 Current firmware language
 
-### Setting: Screen contrast
+### Setting: Screen brightness
 
 Display brightness. Higher values age the OLED faster due to burn-in. (However, it is notable that most of these screens die from other causes first.)
 
@@ -300,3 +300,15 @@ Inverts the entire OLED.
 On device help text:
 
 Invert the colours of the OLED screen
+
+### Setting: Boot logo duration
+
+Sets the duration of the boot logo from 1 second to 4 seconds.
+- For static images this sets the time the logo is displayed for.
+- For animations this sets the time the last frame is displayed for after the animation has been played.
+
+The infinity icon sets a logo or the last frame of an animation to be displayed until a button is pressed.
+
+On device help text:
+
+Sets the duration for the boot logo (S=seconds)

Translations/translation_BE.json

@@ -2,26 +2,17 @@
   "languageCode": "BE",
   "languageLocalName": "Беларуская",
   "fonts": ["ascii_basic", "latin_extended", "cyrillic"],
+  "tempUnitFahrenheit": false,
   "messages": {
-    "SettingsCalibrationDone": "Каліброўка закончана!",
     "SettingsCalibrationWarning": "Перад тым, як працягнуць, каліласка, упэўнецеся, што джала мае комнатную тэмпературу!",
     "SettingsResetWarning": "Вы ўпэннены, што жадаеце зкінуць налады да першапачатковых значэнняў?",
     "UVLOWarningString": "НАПРУГА--",
     "UndervoltageString": "Нізкая напруга",
     "InputVoltageString": "Сілкаванне В: ",
-    "WarningTipTempString": "Тэмп. джала: ",
-    "BadTipString": "ДЖАЛА--",
     "SleepingSimpleString": "Zzzz",
     "SleepingAdvancedString": "Чаканне...",
-    "WarningSimpleString": "ГОРАЧА!",
-    "WarningAdvancedString": "!!! ГАРАЧАЕ !!!\n!!! ДЖАЛА !!!",
     "SleepingTipAdvancedString": "Джала:",
-    "IdleTipString": "Джала:",
-    "IdleSetString": " ->",
-    "TipDisconnectedString": "ДЖАЛА АДЛУЧАНА",
-    "SolderingAdvancedPowerPrompt": "Сілкаванне: ",
-    "OffString": "Выкл.",
-    "YourGainMessage": "Прырост:"
+    "OffString": "Выкл."
   },
   "messagesWarn": {
     "ResetOKMessage": "Скід OK",
@@ -51,8 +42,7 @@
     "SettingSensitivityHigh": "В",
     "SettingLockDisableChar": "А",
     "SettingLockBoostChar": "Т",
-    "SettingLockFullChar": "П",
-    "SettingNAChar": "Н/Д"
+    "SettingLockFullChar": "П"
   },
   "menuGroups": {
     "PowerMenu": {
@@ -208,6 +198,10 @@
     "ColourInversion": {
       "text2": ["Экран", "Інвертаваць"],
       "desc": "Інвертаваць колеры OLED-экрана"
+    },
+    "LOGOTime": {
+      "text2": ["Boot logo", "duration"],
+      "desc": "Sets the duration for the boot logo (S=seconds)"
     }
   }
 }

Translations/translation_BG.json

@@ -2,33 +2,24 @@
   "languageCode": "BG",
   "languageLocalName": "Български",
   "fonts": ["ascii_basic", "cyrillic"],
+  "tempUnitFahrenheit": false,
   "messages": {
-    "SettingsCalibrationDone": "Калибрацията завършена!",
     "SettingsCalibrationWarning": "Уверете се, че върха на поялника е със стайна температура преди да продължите!",
     "SettingsResetWarning": "Сигурни ли сте, че искате да върнете фабричните настройки?",
     "UVLOWarningString": "Ниско DC Напрежение",
     "UndervoltageString": "Ниско Напрежение",
     "InputVoltageString": "Входно V: ",
-    "WarningTipTempString": "Темп.: ",
-    "BadTipString": "ЛОШ ВРЪХ",
     "SleepingSimpleString": "Сън",
     "SleepingAdvancedString": "Хър Хър Хър...",
-    "WarningSimpleString": "ОХ!",
-    "WarningAdvancedString": "ВНИМАНИЕ! ТОПЛО!",
     "SleepingTipAdvancedString": "Връх:",
-    "IdleTipString": "Връх:",
-    "IdleSetString": " Настройка:",
-    "TipDisconnectedString": "ПРЕКЪСНАТ ВРЪХ",
-    "SolderingAdvancedPowerPrompt": "Захранване: ",
-    "OffString": "Изкл.",
-    "YourGainMessage": "Усилване:"
+    "OffString": "Изкл."
   },
   "messagesWarn": {
     "ResetOKMessage": "Нулиране",
     "SettingsResetMessage": ["Настройките бяха", "нулирани!"],
     "NoAccelerometerMessage": ["No accelerometer", "detected!"],
     "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"],
-    "LockingKeysString": " LOCKED",
+    "LockingKeysString": "LOCKED",
     "UnlockingKeysString": "UNLOCKED",
     "WarningKeysLockedString": "!LOCKED!",
     "WarningThermalRunaway": ["Thermal", "Runaway"]
@@ -45,15 +36,13 @@
     "SettingStartSolderingChar": "Р",
     "SettingStartSleepChar": "С",
     "SettingStartSleepOffChar": "П",
-    "SettingStartNoneChar": "F",
     "SettingSensitivityOff": "O",
     "SettingSensitivityLow": "L",
     "SettingSensitivityMedium": "M",
     "SettingSensitivityHigh": "H",
     "SettingLockDisableChar": "D",
     "SettingLockBoostChar": "B",
-    "SettingLockFullChar": "F",
-    "SettingNAChar": "N/A"
+    "SettingLockFullChar": "F"
   },
   "menuGroups": {
     "PowerMenu": {
@@ -148,7 +137,7 @@
     },
     "PDNegTimeout": {
       "text2": ["PD", "timeout"],
-      "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers (0: disabled)"
+      "desc": "PD negotiation timeout in 100ms steps for compatibility with some QC chargers"
     },
     "PowerLimit": {
       "text2": ["Лимит на", "мощност"],
@@ -171,28 +160,28 @@
       "desc": "Поддържане на интензивност на захранващия импулс"
     },
     "HallEffSensitivity": {
-      "text2": ["Hall Eff", "Sensitivity"],
-      "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=Изключено | 1=Слабо | ... | 9=Силно)"
+      "text2": ["Hall sensor", "sensitivity"],
+      "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=Изключено | 1=Слабо | ... | 9=Силно)"
     },
     "LockingMode": {
-      "text2": ["Allow buttons", "locking"],
-      "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)"
+      "text2": ["Allow locking", "buttons"],
+      "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)"
     },
     "MinVolCell": {
       "text2": ["Minimum", "voltage"],
       "desc": "Minimum allowed voltage per cell (3S: 3 - 3,7V | 4-6S: 2,4 - 3,7V)"
     },
     "AnimLoop": {
       "text2": ["Anim.", "loop"],
-      "desc": "Loop icon animations in root menu"
+      "desc": "Loop icon animations in main menu"
     },
     "AnimSpeed": {
       "text2": ["Anim.", "speed"],
-      "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)"
+      "desc": "Pace of icon animations in menu (O=off | S=slow | M=medium | F=fast)"
     },
     "PowerPulseWait": {
-      "text2": ["Power pulse", "wait time"],
-      "desc": "Time to wait before triggering every keep-awake pulse (x 2,5с)"
+      "text2": ["Power pulse", "delay"],
+      "desc": "Delay before keep-awake-pulse is triggered (x 2,5с)"
     },
     "PowerPulseDuration": {
       "text2": ["Power pulse", "duration"],
@@ -203,12 +192,16 @@
       "desc": ""
     },
     "Brightness": {
-      "text2": ["Screen", "Brightness"],
-      "desc": "Adjust the contrast/brightness of the OLED screen"
+      "text2": ["Screen", "brightness"],
+      "desc": "Adjust the brightness of the OLED screen"
     },
     "ColourInversion": {
-      "text2": ["Screen", "Invert"],
+      "text2": ["Invert", "screen"],
       "desc": "Invert the colours of the OLED screen"
+    },
+    "LOGOTime": {
+      "text2": ["Boot logo", "duration"],
+      "desc": "Sets the duration for the boot logo (S=seconds)"
     }
   }
 }

Translations/translation_CS.json

@@ -2,33 +2,24 @@
   "languageCode": "CS",
   "languageLocalName": "Český",
   "fonts": ["ascii_basic", "latin_extended"],
+  "tempUnitFahrenheit": false,
   "messages": {
-    "SettingsCalibrationDone": "Kalibrace dokončena!",
     "SettingsCalibrationWarning": "Ujistěte se, že hrot má pokojovou teplotu!",
     "SettingsResetWarning": "Opravdu chcete resetovat zařízení do továrního nastavení?",
     "UVLOWarningString": "Nízké DC",
     "UndervoltageString": "! Nízké napětí !",
     "InputVoltageString": "Napětí: ",
-    "WarningTipTempString": "Teplota: ",
-    "BadTipString": "ŠP. HROT",
     "SleepingSimpleString": "Zzz ",
     "SleepingAdvancedString": "Režim spánku...",
-    "WarningSimpleString": "PÁLÍ",
-    "WarningAdvancedString": "!! HORKÝ HROT !!",
     "SleepingTipAdvancedString": "Hrot:",
-    "IdleTipString": "Hrot:",
-    "IdleSetString": " Cíl:",
-    "TipDisconnectedString": "HROT NEPŘIPOJEN",
-    "SolderingAdvancedPowerPrompt": "Ohřev: ",
-    "OffString": "Vyp",
-    "YourGainMessage": "Zisk:"
+    "OffString": "Vyp"
   },
   "messagesWarn": {
     "ResetOKMessage": "Reset OK",
     "SettingsResetMessage": ["Tov. nas. obnov.", ""],
     "NoAccelerometerMessage": ["No accelerometer", "detected!"],
     "NoPowerDeliveryMessage": ["No USB-PD IC", "detected!"],
-    "LockingKeysString": " LOCKED",
+    "LockingKeysString": "LOCKED",
     "UnlockingKeysString": "UNLOCKED",
     "WarningKeysLockedString": "!LOCKED!",
     "WarningThermalRunaway": ["Thermal", "Runaway"]
@@ -51,8 +42,7 @@
     "SettingSensitivityHigh": "H",
     "SettingLockDisableChar": "D",
     "SettingLockBoostChar": "B",
-    "SettingLockFullChar": "F",
-    "SettingNAChar": "N/A"
+    "SettingLockFullChar": "F"
   },
   "menuGroups": {
     "PowerMenu": {
@@ -170,28 +160,28 @@
       "desc": "Puls pro udržení zařízení v chodu (kvůli power bankám)."
     },
     "HallEffSensitivity": {
-      "text2": ["Hall Eff", "Sensitivity"],
-      "desc": "Sensitivity of the Hall effect sensor in detecting sleep (0=Vyp | 1=Min | ... | 9=Max)"
+      "text2": ["Hall sensor", "sensitivity"],
+      "desc": "Sensitivity of the Hall effect sensor to detect sleep (0=Vyp | 1=Min | ... | 9=Max)"
     },
     "LockingMode": {
-      "text2": ["Allow buttons", "locking"],
-      "desc": "When soldering, long press on both buttons lock them (D=Disable | B=Boost only | F=Full locking)"
+      "text2": ["Allow locking", "buttons"],
+      "desc": "While soldering, hold down both buttons to toggle locking them (D=disable | B=boost mode only | F=full locking)"
     },
     "MinVolCell": {
       "text2": ["Minimum", "voltage"],
       "desc": "Minimum allowed voltage per cell (3S: 3 - 3,7V | 4-6S: 2,4 - 3,7V)"
     },
     "AnimLoop": {
       "text2": ["Anim.", "loop"],
-      "desc": "Loop icon animations in root menu"
+      "desc": "Loop icon animations in main menu"
     },
     "AnimSpeed": {
       "text2": ["Anim.", "speed"],
-      "desc": "Speed of icon animations in menu (O=off | L=low | M=medium | H=high)"
+      "desc": "Pace of icon animations in menu (O=off | P=slow | M=medium | R=fast)"
     },
     "PowerPulseWait": {
-      "text2": ["Power pulse", "wait time"],
-      "desc": "Time to wait before triggering every keep-awake pulse (x 2,5s)"
+      "text2": ["Power pulse", "delay"],
+      "desc": "Delay before keep-awake-pulse is triggered (x 2,5s)"
     },
     "PowerPulseDuration": {
       "text2": ["Power pulse", "duration"],
@@ -202,12 +192,16 @@
       "desc": ""
     },
     "Brightness": {
-      "text2": ["Screen", "Brightness"],
-      "desc": "Adjust the contrast/brightness of the OLED screen"
+      "text2": ["Screen", "brightness"],
+      "desc": "Adjust the brightness of the OLED screen"
     },
     "ColourInversion": {
-      "text2": ["Screen", "Invert"],
+      "text2": ["Invert", "screen"],
       "desc": "Invert the colours of the OLED screen"
+    },
+    "LOGOTime": {
+      "text2": ["Boot logo", "duration"],
+      "desc": "Sets the duration for the boot logo (S=seconds)"
     }
   }
 }