A program to set instructions and get information from an SPS30. It has been
tested to run either UART or I2C communcation on ESP32, MEGA2560, ESP8266 and UNO.
A detailed description of the options and findings are in SPS30.odt
As part of a larger project I am looking at analyzing and understanding the air quality. I have done a number of projects on air-sensors. The SPS30 sensor is a new kid on the block that looks interesting. This is the first version of a working driver + examples. More work is happening to create examples and compare against other sensors.
A word of warning: the SPS30 needs a female plug of ZHR-5 from JST Sales America Inc. I have not been able to find a good source for that and was glad to buy the Sparkfun version (https://www.sparkfun.com/products/15103) which does include a cable with this plug.
May 2019 : there is also a library available for Raspberry Pi (https://github.com/paulvha/sps30_on_raspberry)
Examples 4, 5, 7,8 and 10 have a dependency on other libraries. Documented in sketch
Obtain the zip and install like any other
Please see the description in the top of the sketch and read the documentation (odt)
- Initial version Arduino, ESP32, UNO
- Added examples 4 (with DS18x20) and 5 (with BME280)
- Added example 6 (plotting data)
- Added ESP8266 support info
- Added force serial1 when TX = RX = 8
- Added flag INCLUDE_SOFTWARE_SERIAL to optionally exclude software Serial
- Tested by Ryan Brown on a Sparkfun Photon RED board and the code should also work with the Photon, P1, and Electrons
- Added example 7 (with SCD)
- Added flag in sps30.h SOFTI2C_ESP32 to use SoftWire on ESP32 in case of SCD30 and SPS30 working on I2C
- Update documentation / instructions
- Added check on the I2C receive buffer. If at least 64 bytes it try to read ALL information else only MASS results
- Updated examples / documentation / instructions
- Added example 8 (SPS30 + SCD30 + BME280)
- Added || defined(AVR_ATmega32U4) || defined(AVR_ATmega16U4) for boards with small footprint (thanks Just van den Broecke)
- Although the AVR_ATmega32U4 has a UART, it does NOT support 115K and can only be connected over I2C.
- fixed the PM10 number always showing 0 issue.
- Added example 9 (with compare typical size)
- Updated the documentation with compare results to SDS011 and Dylos-1700
- Update all examples to have prototypes upfront as the ESP32 pre-processor sometimes does not create
- Added example 10 for ESP32 only: use SPS30 to create an airquality index by region
- update documentation to 1.3
- corrected the stop measurement command (spotted by detamend)
- added support for MKRZERO/SAMD I2C buffer detection and disable softerial
- updated documentation for PROMINI I2C buffer adjustment in odt-file (thanks to input Bert Heusinkveld)
- fixed I2C_Max_bytes error when I2C is excluded in sps30.h
- improve receive buffer checks larger than 3 bytes
- A special version for Feather Lora 32U4 has been created
- fixed ESP32 serial connection / flushing
- optimized the fix from October 2019 for I2C max bytes
- optimized autodetection for SAMD SERCOM and ESP32 to undef softwareSerial
- Paul van Haastrecht ([email protected])
This project is licensed under the GNU GENERAL PUBLIC LICENSE 3.0
Make sure to read the datasheet from Sensirion. While draft it does provide good starting point.
In case you are new to electronics and wonder about pull-up resistors for I2C, see below (thanks to Shane Diller)
