4.9-1.0.x-imx fixes from Toradex branch #20

agners · 2017-12-13T09:03:56Z

This are a bunch of generic fixes we carry in our imx_4.9.11_1.0.0_ga based branch but should be generically applicable.

The USB charger functionality depends on functions provided by CONFIG_POWER_SUPPLY but this dependency is not forced through Kconfig. Don't compile the functionality in when CONFIG_POWER_SUPPLY is not set. This fixes linker errors of not found symbols. power_supply_changed power_supply_register power_supply_unregister Signed-off-by: Max Krummenacher <[email protected]> Signed-off-by: Stefan Agner <[email protected]>

mxsfb seems to have dependencies into mxcfb (it requires mxc_dispdrv_gethandle), hence compile mxc_dispdrv.c unconditionally. Signed-off-by: Stefan Agner <[email protected]> Acked-by: Max Krummenacher <[email protected]>

The PIXDATA flags of the display_flags enum are controller centric, e.g. NEGEDGE means the controller shall drive the data signals on pixelclocks negative edge. However, the drivers flag is display centric: Sample the data on negative (falling) edge. Therefore, change the if statement to check for the POSEDGE flag (which is typically not set): Drive on positive edge => sample on negative edge Signed-off-by: Stefan Agner <[email protected]> Acked-by: Max Krummenacher <[email protected]>

Currently it is not possible to select the mxs dma driver when only mx6sx or mx7 are selected. Extend the dependency to allow the mxs dma driver to be built whenever ARCH_MXS or ARCH_MXC is selected. This has the benefit to avoid having to add new entries in the MXS_DMA Kconfig everytime a new i.MX SoC shows up and it also makes it consistent with the other i.MX DMA engines, such as IMX_DMA and IMX_SDMA. While at it, also pass COMPILE_TEST for increasing the build coverage. Acked-by: Stefan Agner <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Vinod Koul <[email protected]>

Use the timing count from the parsed struct display_timings instead of looping through the device tree again. Signed-off-by: Stefan Agner <[email protected]> Acked-by: Max Krummenacher <[email protected]>

Honor the native-mode property by adding only that mode to the mode list. With that we loose the list of modes, but we currently don't make use of it anyway. Also, the mode list lacks the pixel clock polarity information since struct fb_videomode does not store this information. Signed-off-by: Stefan Agner <[email protected]> Acked-by: Max Krummenacher <[email protected]>

Introduce the "lrclk-strength" property to allow LRCLK pad drive strength to be changed via device tree. When running a stress playback loop test on a mx6dl wandboard channel swap can be noticed on about 10% of the times. While debugging this issue I noticed that when probing the SGTL5000 LRCLK pin with the scope the swap did not happen. After removing the probe the swap started to happen again. After changing the LRCLK pad drive strength to the maximum value the issue is gone. Same fix works on a mx6dl Colibri board as well. Signed-off-by: Fabio Estevam <[email protected]> Tested-by: Max Krummenacher <[email protected]> Signed-off-by: Mark Brown <[email protected]>

The file uses linux,keycode = <KEY_POWER>;, so include the header which defines KEY_POWER. Signed-off-by: Max Krummenacher <[email protected]> Signed-off-by: Stefan Agner <[email protected]>

All PWM clock instances have their clock gate. Add these consistently. Fixes freezing the kernel when one of these instances is used with IMX6UL_CLK_DUMMY as its clock source. Signed-off-by: Max Krummenacher <[email protected]> Signed-off-by: Stefan Agner <[email protected]>

[ Upstream commit 3cf8645 ] Commit 57e5568 ("sata_via: Implement hotplug for VT6421") adds hotplug IRQ handler for VT6421 but enables hotplug on all chips. This is a bug because it causes "irq xx: nobody cared" error on VT6420 when hot-(un)plugging a drive: [ 381.839948] irq 20: nobody cared (try booting with the "irqpoll" option) [ 381.840014] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc5+ #148 [ 381.840066] Hardware name: P4VM800/P4VM800, BIOS P1.60 05/29/2006 [ 381.840117] Call Trace: [ 381.840167] <IRQ> [ 381.840225] ? dump_stack+0x44/0x58 [ 381.840278] ? __report_bad_irq+0x14/0x97 [ 381.840327] ? handle_edge_irq+0xa5/0xa5 [ 381.840376] ? note_interrupt+0x155/0x1cf [ 381.840426] ? handle_edge_irq+0xa5/0xa5 [ 381.840474] ? handle_irq_event_percpu+0x32/0x38 [ 381.840524] ? handle_irq_event+0x1f/0x38 [ 381.840573] ? handle_fasteoi_irq+0x69/0xb8 [ 381.840625] ? handle_irq+0x4f/0x5d [ 381.840672] </IRQ> [ 381.840726] ? do_IRQ+0x2e/0x8b [ 381.840782] ? common_interrupt+0x2c/0x34 [ 381.840836] ? mwait_idle+0x60/0x82 [ 381.840892] ? arch_cpu_idle+0x6/0x7 [ 381.840949] ? do_idle+0x96/0x18e [ 381.841002] ? cpu_startup_entry+0x16/0x1a [ 381.841057] ? start_kernel+0x319/0x31c [ 381.841111] ? startup_32_smp+0x166/0x168 [ 381.841165] handlers: [ 381.841219] [<c12a7263>] ata_bmdma_interrupt [ 381.841274] Disabling IRQ #20 Seems that VT6420 can do hotplug too (there's no documentation) but the comments say that SCR register access (required for detecting hotplug events) can cause problems on these chips. For now, just keep hotplug disabled on anything other than VT6421. Signed-off-by: Ondrej Zary <[email protected]> Signed-off-by: Tejun Heo <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 666b5d1 ] Remove spinlock and use the "rtc->ops_lock" from RTC subsystem instead. spin_lock_irqsave() is not needed here because we do not have hard IRQs. This patch fixes the following issue: root@GE004097290448 b850v3:~# hwclock --systohc root@GE004097290448 b850v3:~# hwclock --systohc root@GE004097290448 b850v3:~# hwclock --systohc root@GE004097290448 b850v3:~# hwclock --systohc root@GE004097290448 b850v3:~# hwclock --systohc [ 82.108175] BUG: spinlock wrong CPU on CPU#0, hwclock/855 [ 82.113660] lock: 0xedb4899c, .magic: dead4ead, .owner: hwclock/855, .owner_cpu: 1 [ 82.121329] CPU: 0 PID: 855 Comm: hwclock Not tainted 4.8.0-00042-g09d5410-dirty #20 [ 82.129078] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 82.135609] Backtrace: [ 82.138090] [<8010d378>] (dump_backtrace) from [<8010d5c0>] (show_stack+0x20/0x24) [ 82.145664] r7:ec936000 r6:600a0013 r5:00000000 r4:81031680 [ 82.151402] [<8010d5a0>] (show_stack) from [<80401518>] (dump_stack+0xb4/0xe8) [ 82.158636] [<80401464>] (dump_stack) from [<8017b8b0>] (spin_dump+0x84/0xcc) [ 82.165775] r10:00000000 r9:ec936000 r8:81056090 r7:600a0013 r6:edb4899c r5:edb4899c [ 82.173691] r4:e5033e00 r3:00000000 [ 82.177308] [<8017b82c>] (spin_dump) from [<8017bcb0>] (do_raw_spin_unlock+0x108/0x130) [ 82.185314] r5:edb4899c r4:edb4899c [ 82.188938] [<8017bba8>] (do_raw_spin_unlock) from [<8094b93c>] (_raw_spin_unlock_irqrestore+0x34/0x54) [ 82.198333] r5:edb4899c r4:600a0013 [ 82.201953] [<8094b908>] (_raw_spin_unlock_irqrestore) from [<8065b090>] (rx8010_set_time+0x14c/0x188) [ 82.211261] r5:00000020 r4:edb48990 [ 82.214882] [<8065af44>] (rx8010_set_time) from [<80653fe4>] (rtc_set_time+0x70/0x104) [ 82.222801] r7:00000051 r6:edb39da0 r5:edb39c00 r4:ec937e8c [ 82.228535] [<80653f74>] (rtc_set_time) from [<80655774>] (rtc_dev_ioctl+0x3c4/0x674) [ 82.236368] r7:00000051 r6:7ecf1b74 r5:00000000 r4:edb39c00 [ 82.242106] [<806553b0>] (rtc_dev_ioctl) from [<80284034>] (do_vfs_ioctl+0xa4/0xa6c) [ 82.249851] r8:00000003 r7:80284a40 r6:ed1e9c80 r5:edb44e60 r4:7ecf1b74 [ 82.256642] [<80283f90>] (do_vfs_ioctl) from [<80284a40>] (SyS_ioctl+0x44/0x6c) [ 82.263953] r10:00000000 r9:ec936000 r8:7ecf1b74 r7:4024700a r6:ed1e9c80 r5:00000003 [ 82.271869] r4:ed1e9c80 [ 82.274432] [<802849fc>] (SyS_ioctl) from [<80108520>] (ret_fast_syscall+0x0/0x1c) [ 82.282005] r9:ec936000 r8:801086c4 r7:00000036 r6:00000000 r5:00000003 r4:0008e1bc root@GE004097290448 b850v3:~# Message from syslogd@GE004097290448 at Dec 3 11:17:08 ... kernel:[ 82.108175] BUG: spinlock wrong CPU on CPU#0, hwclock/855 Message from syslogd@GE004097290448 at Dec 3 11:17:08 ... kernel:[ 82.113660] lock: 0xedb4899c, .magic: dead4ead, .owner: hwclock/855, .owner_cpu: 1 hwclock --systohc root@GE004097290448 b850v3:~# Signed-off-by: Fabien Lahoudere <[email protected]> Signed-off-by: Alexandre Belloni <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

4.9-1.0.x-imx fixes from Toradex branch

[ Upstream commit 2bbea6e ] when mounting an ISO filesystem sometimes (very rarely) the system hangs because of a race condition between two tasks. PID: 6766 TASK: ffff88007b2a6dd0 CPU: 0 COMMAND: "mount" #0 [ffff880078447ae0] __schedule at ffffffff8168d605 #1 [ffff880078447b48] schedule_preempt_disabled at ffffffff8168ed49 #2 [ffff880078447b58] __mutex_lock_slowpath at ffffffff8168c995 #3 [ffff880078447bb8] mutex_lock at ffffffff8168bdef #4 [ffff880078447bd0] sr_block_ioctl at ffffffffa00b6818 [sr_mod] #5 [ffff880078447c10] blkdev_ioctl at ffffffff812fea50 #6 [ffff880078447c70] ioctl_by_bdev at ffffffff8123a8b3 #7 [ffff880078447c90] isofs_fill_super at ffffffffa04fb1e1 [isofs] #8 [ffff880078447da8] mount_bdev at ffffffff81202570 #9 [ffff880078447e18] isofs_mount at ffffffffa04f9828 [isofs] #10 [ffff880078447e28] mount_fs at ffffffff81202d09 #11 [ffff880078447e70] vfs_kern_mount at ffffffff8121ea8f #12 [ffff880078447ea8] do_mount at ffffffff81220fee #13 [ffff880078447f28] sys_mount at ffffffff812218d6 #14 [ffff880078447f80] system_call_fastpath at ffffffff81698c49 RIP: 00007fd9ea914e9a RSP: 00007ffd5d9bf648 RFLAGS: 00010246 RAX: 00000000000000a5 RBX: ffffffff81698c49 RCX: 0000000000000010 RDX: 00007fd9ec2bc210 RSI: 00007fd9ec2bc290 RDI: 00007fd9ec2bcf30 RBP: 0000000000000000 R8: 0000000000000000 R9: 0000000000000010 R10: 00000000c0ed0001 R11: 0000000000000206 R12: 00007fd9ec2bc040 R13: 00007fd9eb6b2380 R14: 00007fd9ec2bc210 R15: 00007fd9ec2bcf30 ORIG_RAX: 00000000000000a5 CS: 0033 SS: 002b This task was trying to mount the cdrom. It allocated and configured a super_block struct and owned the write-lock for the super_block->s_umount rwsem. While exclusively owning the s_umount lock, it called sr_block_ioctl and waited to acquire the global sr_mutex lock. PID: 6785 TASK: ffff880078720fb0 CPU: 0 COMMAND: "systemd-udevd" #0 [ffff880078417898] __schedule at ffffffff8168d605 #1 [ffff880078417900] schedule at ffffffff8168dc59 #2 [ffff880078417910] rwsem_down_read_failed at ffffffff8168f605 #3 [ffff880078417980] call_rwsem_down_read_failed at ffffffff81328838 #4 [ffff8800784179d0] down_read at ffffffff8168cde0 #5 [ffff8800784179e8] get_super at ffffffff81201cc7 #6 [ffff880078417a10] __invalidate_device at ffffffff8123a8de #7 [ffff880078417a40] flush_disk at ffffffff8123a94b #8 [ffff880078417a88] check_disk_change at ffffffff8123ab50 #9 [ffff880078417ab0] cdrom_open at ffffffffa00a29e1 [cdrom] #10 [ffff880078417b68] sr_block_open at ffffffffa00b6f9b [sr_mod] #11 [ffff880078417b98] __blkdev_get at ffffffff8123ba86 #12 [ffff880078417bf0] blkdev_get at ffffffff8123bd65 #13 [ffff880078417c78] blkdev_open at ffffffff8123bf9b #14 [ffff880078417c90] do_dentry_open at ffffffff811fc7f7 #15 [ffff880078417cd8] vfs_open at ffffffff811fc9cf #16 [ffff880078417d00] do_last at ffffffff8120d53d #17 [ffff880078417db0] path_openat at ffffffff8120e6b2 #18 [ffff880078417e48] do_filp_open at ffffffff8121082b #19 [ffff880078417f18] do_sys_open at ffffffff811fdd33 #20 [ffff880078417f70] sys_open at ffffffff811fde4e #21 [ffff880078417f80] system_call_fastpath at ffffffff81698c49 RIP: 00007f29438b0c20 RSP: 00007ffc76624b78 RFLAGS: 00010246 RAX: 0000000000000002 RBX: ffffffff81698c49 RCX: 0000000000000000 RDX: 00007f2944a5fa70 RSI: 00000000000a0800 RDI: 00007f2944a5fa70 RBP: 00007f2944a5f540 R8: 0000000000000000 R9: 0000000000000020 R10: 00007f2943614c40 R11: 0000000000000246 R12: ffffffff811fde4e R13: ffff880078417f78 R14: 000000000000000c R15: 00007f2944a4b010 ORIG_RAX: 0000000000000002 CS: 0033 SS: 002b This task tried to open the cdrom device, the sr_block_open function acquired the global sr_mutex lock. The call to check_disk_change() then saw an event flag indicating a possible media change and tried to flush any cached data for the device. As part of the flush, it tried to acquire the super_block->s_umount lock associated with the cdrom device. This was the same super_block as created and locked by the previous task. The first task acquires the s_umount lock and then the sr_mutex_lock; the second task acquires the sr_mutex_lock and then the s_umount lock. This patch fixes the issue by moving check_disk_change() out of cdrom_open() and let the caller take care of it. Signed-off-by: Maurizio Lombardi <[email protected]> Signed-off-by: Jens Axboe <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit a5ba1d9 upstream. We have reports of the following crash: PID: 7 TASK: ffff88085c6d61c0 CPU: 1 COMMAND: "kworker/u25:0" #0 [ffff88085c6db710] machine_kexec at ffffffff81046239 #1 [ffff88085c6db760] crash_kexec at ffffffff810fc248 #2 [ffff88085c6db830] oops_end at ffffffff81008ae7 #3 [ffff88085c6db860] no_context at ffffffff81050b8f #4 [ffff88085c6db8b0] __bad_area_nosemaphore at ffffffff81050d75 #5 [ffff88085c6db900] bad_area_nosemaphore at ffffffff81050e83 #6 [ffff88085c6db910] __do_page_fault at ffffffff8105132e #7 [ffff88085c6db9b0] do_page_fault at ffffffff8105152c #8 [ffff88085c6db9c0] page_fault at ffffffff81a3f122 [exception RIP: uart_put_char+149] RIP: ffffffff814b67b5 RSP: ffff88085c6dba78 RFLAGS: 00010006 RAX: 0000000000000292 RBX: ffffffff827c5120 RCX: 0000000000000081 RDX: 0000000000000000 RSI: 000000000000005f RDI: ffffffff827c5120 RBP: ffff88085c6dba98 R8: 000000000000012c R9: ffffffff822ea320 R10: ffff88085fe4db04 R11: 0000000000000001 R12: ffff881059f9c000 R13: 0000000000000001 R14: 000000000000005f R15: 0000000000000fba ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #9 [ffff88085c6dbaa0] tty_put_char at ffffffff81497544 #10 [ffff88085c6dbac0] do_output_char at ffffffff8149c91c #11 [ffff88085c6dbae0] __process_echoes at ffffffff8149cb8b #12 [ffff88085c6dbb30] commit_echoes at ffffffff8149cdc2 #13 [ffff88085c6dbb60] n_tty_receive_buf_fast at ffffffff8149e49b #14 [ffff88085c6dbbc0] __receive_buf at ffffffff8149ef5a #15 [ffff88085c6dbc20] n_tty_receive_buf_common at ffffffff8149f016 #16 [ffff88085c6dbca0] n_tty_receive_buf2 at ffffffff8149f194 #17 [ffff88085c6dbcb0] flush_to_ldisc at ffffffff814a238a #18 [ffff88085c6dbd50] process_one_work at ffffffff81090be2 #19 [ffff88085c6dbe20] worker_thread at ffffffff81091b4d #20 [ffff88085c6dbeb0] kthread at ffffffff81096384 #21 [ffff88085c6dbf50] ret_from_fork at ffffffff81a3d69f after slogging through some dissasembly: ffffffff814b6720 <uart_put_char>: ffffffff814b6720: 55 push %rbp ffffffff814b6721: 48 89 e5 mov %rsp,%rbp ffffffff814b6724: 48 83 ec 20 sub $0x20,%rsp ffffffff814b6728: 48 89 1c 24 mov %rbx,(%rsp) ffffffff814b672c: 4c 89 64 24 08 mov %r12,0x8(%rsp) ffffffff814b6731: 4c 89 6c 24 10 mov %r13,0x10(%rsp) ffffffff814b6736: 4c 89 74 24 18 mov %r14,0x18(%rsp) ffffffff814b673b: e8 b0 8e 58 00 callq ffffffff81a3f5f0 <mcount> ffffffff814b6740: 4c 8b a7 88 02 00 00 mov 0x288(%rdi),%r12 ffffffff814b6747: 45 31 ed xor %r13d,%r13d ffffffff814b674a: 41 89 f6 mov %esi,%r14d ffffffff814b674d: 49 83 bc 24 70 01 00 cmpq $0x0,0x170(%r12) ffffffff814b6754: 00 00 ffffffff814b6756: 49 8b 9c 24 80 01 00 mov 0x180(%r12),%rbx ffffffff814b675d: 00 ffffffff814b675e: 74 2f je ffffffff814b678f <uart_put_char+0x6f> ffffffff814b6760: 48 89 df mov %rbx,%rdi ffffffff814b6763: e8 a8 67 58 00 callq ffffffff81a3cf10 <_raw_spin_lock_irqsave> ffffffff814b6768: 41 8b 8c 24 78 01 00 mov 0x178(%r12),%ecx ffffffff814b676f: 00 ffffffff814b6770: 89 ca mov %ecx,%edx ffffffff814b6772: f7 d2 not %edx ffffffff814b6774: 41 03 94 24 7c 01 00 add 0x17c(%r12),%edx ffffffff814b677b: 00 ffffffff814b677c: 81 e2 ff 0f 00 00 and $0xfff,%edx ffffffff814b6782: 75 23 jne ffffffff814b67a7 <uart_put_char+0x87> ffffffff814b6784: 48 89 c6 mov %rax,%rsi ffffffff814b6787: 48 89 df mov %rbx,%rdi ffffffff814b678a: e8 e1 64 58 00 callq ffffffff81a3cc70 <_raw_spin_unlock_irqrestore> ffffffff814b678f: 44 89 e8 mov %r13d,%eax ffffffff814b6792: 48 8b 1c 24 mov (%rsp),%rbx ffffffff814b6796: 4c 8b 64 24 08 mov 0x8(%rsp),%r12 ffffffff814b679b: 4c 8b 6c 24 10 mov 0x10(%rsp),%r13 ffffffff814b67a0: 4c 8b 74 24 18 mov 0x18(%rsp),%r14 ffffffff814b67a5: c9 leaveq ffffffff814b67a6: c3 retq ffffffff814b67a7: 49 8b 94 24 70 01 00 mov 0x170(%r12),%rdx ffffffff814b67ae: 00 ffffffff814b67af: 48 63 c9 movslq %ecx,%rcx ffffffff814b67b2: 41 b5 01 mov $0x1,%r13b ffffffff814b67b5: 44 88 34 0a mov %r14b,(%rdx,%rcx,1) ffffffff814b67b9: 41 8b 94 24 78 01 00 mov 0x178(%r12),%edx ffffffff814b67c0: 00 ffffffff814b67c1: 83 c2 01 add $0x1,%edx ffffffff814b67c4: 81 e2 ff 0f 00 00 and $0xfff,%edx ffffffff814b67ca: 41 89 94 24 78 01 00 mov %edx,0x178(%r12) ffffffff814b67d1: 00 ffffffff814b67d2: eb b0 jmp ffffffff814b6784 <uart_put_char+0x64> ffffffff814b67d4: 66 66 66 2e 0f 1f 84 data32 data32 nopw %cs:0x0(%rax,%rax,1) ffffffff814b67db: 00 00 00 00 00 for our build, this is crashing at: circ->buf[circ->head] = c; Looking in uart_port_startup(), it seems that circ->buf (state->xmit.buf) protected by the "per-port mutex", which based on uart_port_check() is state->port.mutex. Indeed, the lock acquired in uart_put_char() is uport->lock, i.e. not the same lock. Anyway, since the lock is not acquired, if uart_shutdown() is called, the last chunk of that function may release state->xmit.buf before its assigned to null, and cause the race above. To fix it, let's lock uport->lock when allocating/deallocating state->xmit.buf in addition to the per-port mutex. v2: switch to locking uport->lock on allocation/deallocation instead of locking the per-port mutex in uart_put_char. Note that since uport->lock is a spin lock, we have to switch the allocation to GFP_ATOMIC. v3: move the allocation outside the lock, so we can switch back to GFP_KERNEL Signed-off-by: Tycho Andersen <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit a5ba1d9 upstream. We have reports of the following crash: PID: 7 TASK: ffff88085c6d61c0 CPU: 1 COMMAND: "kworker/u25:0" #0 [ffff88085c6db710] machine_kexec at ffffffff81046239 Freescale#1 [ffff88085c6db760] crash_kexec at ffffffff810fc248 Freescale#2 [ffff88085c6db830] oops_end at ffffffff81008ae7 Freescale#3 [ffff88085c6db860] no_context at ffffffff81050b8f Freescale#4 [ffff88085c6db8b0] __bad_area_nosemaphore at ffffffff81050d75 Freescale#5 [ffff88085c6db900] bad_area_nosemaphore at ffffffff81050e83 Freescale#6 [ffff88085c6db910] __do_page_fault at ffffffff8105132e Freescale#7 [ffff88085c6db9b0] do_page_fault at ffffffff8105152c Freescale#8 [ffff88085c6db9c0] page_fault at ffffffff81a3f122 [exception RIP: uart_put_char+149] RIP: ffffffff814b67b5 RSP: ffff88085c6dba78 RFLAGS: 00010006 RAX: 0000000000000292 RBX: ffffffff827c5120 RCX: 0000000000000081 RDX: 0000000000000000 RSI: 000000000000005f RDI: ffffffff827c5120 RBP: ffff88085c6dba98 R8: 000000000000012c R9: ffffffff822ea320 R10: ffff88085fe4db04 R11: 0000000000000001 R12: ffff881059f9c000 R13: 0000000000000001 R14: 000000000000005f R15: 0000000000000fba ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 Freescale#9 [ffff88085c6dbaa0] tty_put_char at ffffffff81497544 Freescale#10 [ffff88085c6dbac0] do_output_char at ffffffff8149c91c Freescale#11 [ffff88085c6dbae0] __process_echoes at ffffffff8149cb8b Freescale#12 [ffff88085c6dbb30] commit_echoes at ffffffff8149cdc2 Freescale#13 [ffff88085c6dbb60] n_tty_receive_buf_fast at ffffffff8149e49b Freescale#14 [ffff88085c6dbbc0] __receive_buf at ffffffff8149ef5a Freescale#15 [ffff88085c6dbc20] n_tty_receive_buf_common at ffffffff8149f016 Freescale#16 [ffff88085c6dbca0] n_tty_receive_buf2 at ffffffff8149f194 Freescale#17 [ffff88085c6dbcb0] flush_to_ldisc at ffffffff814a238a Freescale#18 [ffff88085c6dbd50] process_one_work at ffffffff81090be2 Freescale#19 [ffff88085c6dbe20] worker_thread at ffffffff81091b4d Freescale#20 [ffff88085c6dbeb0] kthread at ffffffff81096384 Freescale#21 [ffff88085c6dbf50] ret_from_fork at ffffffff81a3d69f after slogging through some dissasembly: ffffffff814b6720 <uart_put_char>: ffffffff814b6720: 55 push %rbp ffffffff814b6721: 48 89 e5 mov %rsp,%rbp ffffffff814b6724: 48 83 ec 20 sub $0x20,%rsp ffffffff814b6728: 48 89 1c 24 mov %rbx,(%rsp) ffffffff814b672c: 4c 89 64 24 08 mov %r12,0x8(%rsp) ffffffff814b6731: 4c 89 6c 24 10 mov %r13,0x10(%rsp) ffffffff814b6736: 4c 89 74 24 18 mov %r14,0x18(%rsp) ffffffff814b673b: e8 b0 8e 58 00 callq ffffffff81a3f5f0 <mcount> ffffffff814b6740: 4c 8b a7 88 02 00 00 mov 0x288(%rdi),%r12 ffffffff814b6747: 45 31 ed xor %r13d,%r13d ffffffff814b674a: 41 89 f6 mov %esi,%r14d ffffffff814b674d: 49 83 bc 24 70 01 00 cmpq $0x0,0x170(%r12) ffffffff814b6754: 00 00 ffffffff814b6756: 49 8b 9c 24 80 01 00 mov 0x180(%r12),%rbx ffffffff814b675d: 00 ffffffff814b675e: 74 2f je ffffffff814b678f <uart_put_char+0x6f> ffffffff814b6760: 48 89 df mov %rbx,%rdi ffffffff814b6763: e8 a8 67 58 00 callq ffffffff81a3cf10 <_raw_spin_lock_irqsave> ffffffff814b6768: 41 8b 8c 24 78 01 00 mov 0x178(%r12),%ecx ffffffff814b676f: 00 ffffffff814b6770: 89 ca mov %ecx,%edx ffffffff814b6772: f7 d2 not %edx ffffffff814b6774: 41 03 94 24 7c 01 00 add 0x17c(%r12),%edx ffffffff814b677b: 00 ffffffff814b677c: 81 e2 ff 0f 00 00 and $0xfff,%edx ffffffff814b6782: 75 23 jne ffffffff814b67a7 <uart_put_char+0x87> ffffffff814b6784: 48 89 c6 mov %rax,%rsi ffffffff814b6787: 48 89 df mov %rbx,%rdi ffffffff814b678a: e8 e1 64 58 00 callq ffffffff81a3cc70 <_raw_spin_unlock_irqrestore> ffffffff814b678f: 44 89 e8 mov %r13d,%eax ffffffff814b6792: 48 8b 1c 24 mov (%rsp),%rbx ffffffff814b6796: 4c 8b 64 24 08 mov 0x8(%rsp),%r12 ffffffff814b679b: 4c 8b 6c 24 10 mov 0x10(%rsp),%r13 ffffffff814b67a0: 4c 8b 74 24 18 mov 0x18(%rsp),%r14 ffffffff814b67a5: c9 leaveq ffffffff814b67a6: c3 retq ffffffff814b67a7: 49 8b 94 24 70 01 00 mov 0x170(%r12),%rdx ffffffff814b67ae: 00 ffffffff814b67af: 48 63 c9 movslq %ecx,%rcx ffffffff814b67b2: 41 b5 01 mov $0x1,%r13b ffffffff814b67b5: 44 88 34 0a mov %r14b,(%rdx,%rcx,1) ffffffff814b67b9: 41 8b 94 24 78 01 00 mov 0x178(%r12),%edx ffffffff814b67c0: 00 ffffffff814b67c1: 83 c2 01 add $0x1,%edx ffffffff814b67c4: 81 e2 ff 0f 00 00 and $0xfff,%edx ffffffff814b67ca: 41 89 94 24 78 01 00 mov %edx,0x178(%r12) ffffffff814b67d1: 00 ffffffff814b67d2: eb b0 jmp ffffffff814b6784 <uart_put_char+0x64> ffffffff814b67d4: 66 66 66 2e 0f 1f 84 data32 data32 nopw %cs:0x0(%rax,%rax,1) ffffffff814b67db: 00 00 00 00 00 for our build, this is crashing at: circ->buf[circ->head] = c; Looking in uart_port_startup(), it seems that circ->buf (state->xmit.buf) protected by the "per-port mutex", which based on uart_port_check() is state->port.mutex. Indeed, the lock acquired in uart_put_char() is uport->lock, i.e. not the same lock. Anyway, since the lock is not acquired, if uart_shutdown() is called, the last chunk of that function may release state->xmit.buf before its assigned to null, and cause the race above. To fix it, let's lock uport->lock when allocating/deallocating state->xmit.buf in addition to the per-port mutex. v2: switch to locking uport->lock on allocation/deallocation instead of locking the per-port mutex in uart_put_char. Note that since uport->lock is a spin lock, we have to switch the allocation to GFP_ATOMIC. v3: move the allocation outside the lock, so we can switch back to GFP_KERNEL Signed-off-by: Tycho Andersen <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 20cdcaf ] During the duplication of em28xx state for the second tuner pair a pointer to alt_max_pkt_size_isoc is copied. During tear down the second tuner is destroyed first and kfrees alt_max_pkt_size_isoc, then the first tuner is destroyed and kfrees it again. The property should only be kfree'd if the tuner is PRIMARY_TS. [ 354.888560] ------------[ cut here ]------------ [ 354.888562] kernel BUG at mm/slub.c:296! [ 354.888574] invalid opcode: 0000 [Freescale#1] SMP NOPTI [ 354.888869] CPU: 1 PID: 19 Comm: kworker/1:0 Not tainted 4.18.0-rc1+ Freescale#20 [ 354.889140] Hardware name: MSI MS-7A39/B350M GAMING PRO (MS-7A39), BIOS 2.G0 04/27/2018 [ 354.889408] Workqueue: usb_hub_wq hub_event [ 354.889679] RIP: 0010:__slab_free+0x217/0x370 [ 354.889942] Code: bb c0 e8 07 41 38 c7 72 39 48 83 c4 70 5b 41 5a 41 5c 41 5d 41 5e 41 5f 5d 49 8d 62 f8 c3 f3 90 49 8b 04 24 a8 01 75 f6 eb 82 <0f> 0b 44 89 45 80 48 89 4d 88 e8 aa fa ff ff 85 c0 74 cc e9 b7 fe [ 354.890598] RSP: 0018:ffffb84c41a4fad0 EFLAGS: 00010246 [ 354.890934] RAX: ffff948646e85150 RBX: ffff948646e85150 RCX: ffff948646e85150 [ 354.891280] RDX: 00000000820001d9 RSI: fffffa8fd01ba140 RDI: ffff94865e807c00 [ 354.891649] RBP: ffffb84c41a4fb70 R08: 0000000000000001 R09: ffffffffc059ce21 [ 354.892025] R10: ffff948646e85150 R11: 0000000000000001 R12: fffffa8fd01ba140 [ 354.892403] R13: ffff948646e85150 R14: ffff94865e807c00 R15: ffff94864c92e0a0 [ 354.892780] FS: 0000000000000000(0000) GS:ffff94865ec40000(0000) knlGS:0000000000000000 [ 354.893150] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 354.893530] CR2: 00007f4e476da950 CR3: 000000040112c000 CR4: 00000000003406e0 [ 354.893917] Call Trace: [ 354.894315] ? __dev_printk+0x3c/0x80 [ 354.894695] ? _dev_info+0x64/0x80 [ 354.895082] ? em28xx_free_device+0x41/0x50 [em28xx] [ 354.895464] kfree+0x17a/0x190 [ 354.895852] ? kfree+0x17a/0x190 [ 354.896310] em28xx_free_device+0x41/0x50 [em28xx] [ 354.896698] em28xx_usb_disconnect+0xfa/0x110 [em28xx] [ 354.897083] usb_unbind_interface+0x7a/0x270 [ 354.897475] device_release_driver_internal+0x17c/0x250 [ 354.897864] device_release_driver+0x12/0x20 [ 354.898252] bus_remove_device+0xec/0x160 [ 354.898639] device_del+0x13d/0x320 [ 354.899018] ? usb_remove_ep_devs+0x1f/0x30 [ 354.899392] usb_disable_device+0x9e/0x270 [ 354.899772] usb_disconnect+0x92/0x2a0 [ 354.900149] hub_event+0x98e/0x1650 [ 354.900519] ? sched_clock_cpu+0x11/0xa0 [ 354.900890] process_one_work+0x167/0x3f0 [ 354.901251] worker_thread+0x4d/0x460 [ 354.901610] kthread+0x105/0x140 [ 354.901964] ? rescuer_thread+0x360/0x360 [ 354.902318] ? kthread_associate_blkcg+0xa0/0xa0 [ 354.902672] ret_from_fork+0x22/0x40 [ 354.903024] Modules linked in: rc_hauppauge em28xx_rc rc_core si2157 lgdt3306a i2c_mux em28xx_dvb dvb_core videobuf2_vmalloc videobuf2_memops videobuf2_common snd_hda_codec_hdmi nls_iso8859_1 edac_mce_amd kvm crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_pcm snd_seq_midi aesni_intel snd_seq_midi_event aes_x86_64 snd_rawmidi crypto_simd em28xx cryptd glue_helper asix tveeprom usbnet snd_seq v4l2_common mii videodev snd_seq_device media input_leds snd_timer joydev ccp k10temp wmi_bmof snd soundcore mac_hid sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables vfio_pci vfio_virqfd irqbypass vfio_iommu_type1 vfio nouveau mxm_wmi video i2c_algo_bit ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops i2c_piix4 drm ahci libahci [ 354.905129] wmi gpio_amdpt gpio_generic hid_generic usbhid hid [ 354.908140] ---[ end trace c230d02716298c34 ]--- [ 354.908145] RIP: 0010:__slab_free+0x217/0x370 [ 354.908147] Code: bb c0 e8 07 41 38 c7 72 39 48 83 c4 70 5b 41 5a 41 5c 41 5d 41 5e 41 5f 5d 49 8d 62 f8 c3 f3 90 49 8b 04 24 a8 01 75 f6 eb 82 <0f> 0b 44 89 45 80 48 89 4d 88 e8 aa fa ff ff 85 c0 74 cc e9 b7 fe [ 354.908183] RSP: 0018:ffffb84c41a4fad0 EFLAGS: 00010246 [ 354.908186] RAX: ffff948646e85150 RBX: ffff948646e85150 RCX: ffff948646e85150 [ 354.908189] RDX: 00000000820001d9 RSI: fffffa8fd01ba140 RDI: ffff94865e807c00 [ 354.908191] RBP: ffffb84c41a4fb70 R08: 0000000000000001 R09: ffffffffc059ce21 [ 354.908193] R10: ffff948646e85150 R11: 0000000000000001 R12: fffffa8fd01ba140 [ 354.908195] R13: ffff948646e85150 R14: ffff94865e807c00 R15: ffff94864c92e0a0 [ 354.908198] FS: 0000000000000000(0000) GS:ffff94865ec40000(0000) knlGS:0000000000000000 [ 354.908201] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 354.908203] CR2: 00007f4e476da950 CR3: 000000016b20a000 CR4: 00000000003406e0 Signed-off-by: Brad Love <[email protected]> Signed-off-by: Michael Ira Krufky <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 54451f6 ] When IDLETIMER rule is added, sysfs file is created under /sys/class/xt_idletimer/timers/ But some label name shouldn't be used. ".", "..", "power", "uevent", "subsystem", etc... So that sysfs filename checking routine is needed. test commands: %iptables -I INPUT -j IDLETIMER --timeout 1 --label "power" splat looks like: [95765.423132] sysfs: cannot create duplicate filename '/devices/virtual/xt_idletimer/timers/power' [95765.433418] CPU: 0 PID: 8446 Comm: iptables Not tainted 4.19.0-rc6+ #20 [95765.449755] Call Trace: [95765.449755] dump_stack+0xc9/0x16b [95765.449755] ? show_regs_print_info+0x5/0x5 [95765.449755] sysfs_warn_dup+0x74/0x90 [95765.449755] sysfs_add_file_mode_ns+0x352/0x500 [95765.449755] sysfs_create_file_ns+0x179/0x270 [95765.449755] ? sysfs_add_file_mode_ns+0x500/0x500 [95765.449755] ? idletimer_tg_checkentry+0x3e5/0xb1b [xt_IDLETIMER] [95765.449755] ? rcu_read_lock_sched_held+0x114/0x130 [95765.449755] ? __kmalloc_track_caller+0x211/0x2b0 [95765.449755] ? memcpy+0x34/0x50 [95765.449755] idletimer_tg_checkentry+0x4e2/0xb1b [xt_IDLETIMER] [ ... ] Fixes: 0902b46 ("netfilter: xtables: idletimer target implementation") Signed-off-by: Taehee Yoo <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 54451f6 ] When IDLETIMER rule is added, sysfs file is created under /sys/class/xt_idletimer/timers/ But some label name shouldn't be used. ".", "..", "power", "uevent", "subsystem", etc... So that sysfs filename checking routine is needed. test commands: %iptables -I INPUT -j IDLETIMER --timeout 1 --label "power" splat looks like: [95765.423132] sysfs: cannot create duplicate filename '/devices/virtual/xt_idletimer/timers/power' [95765.433418] CPU: 0 PID: 8446 Comm: iptables Not tainted 4.19.0-rc6+ Freescale#20 [95765.449755] Call Trace: [95765.449755] dump_stack+0xc9/0x16b [95765.449755] ? show_regs_print_info+0x5/0x5 [95765.449755] sysfs_warn_dup+0x74/0x90 [95765.449755] sysfs_add_file_mode_ns+0x352/0x500 [95765.449755] sysfs_create_file_ns+0x179/0x270 [95765.449755] ? sysfs_add_file_mode_ns+0x500/0x500 [95765.449755] ? idletimer_tg_checkentry+0x3e5/0xb1b [xt_IDLETIMER] [95765.449755] ? rcu_read_lock_sched_held+0x114/0x130 [95765.449755] ? __kmalloc_track_caller+0x211/0x2b0 [95765.449755] ? memcpy+0x34/0x50 [95765.449755] idletimer_tg_checkentry+0x4e2/0xb1b [xt_IDLETIMER] [ ... ] Fixes: 0902b46 ("netfilter: xtables: idletimer target implementation") Signed-off-by: Taehee Yoo <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 97b2a31 upstream. Currently on driver bringup with KASAN enabled, meson triggers an OOB memory access as shown below: [ 117.904528] ================================================================== [ 117.904560] BUG: KASAN: global-out-of-bounds in meson_viu_set_osd_lut+0x7a0/0x890 [ 117.904588] Read of size 4 at addr ffff20000a63ce24 by task systemd-udevd/498 [ 117.904601] [ 118.083372] CPU: 4 PID: 498 Comm: systemd-udevd Not tainted 4.20.0-rc3Lyude-Test+ Freescale#20 [ 118.091143] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018 [ 118.099768] Call trace: [ 118.102181] dump_backtrace+0x0/0x3e8 [ 118.105796] show_stack+0x14/0x20 [ 118.109083] dump_stack+0x130/0x1c4 [ 118.112539] print_address_description+0x60/0x25c [ 118.117214] kasan_report+0x1b4/0x368 [ 118.120851] __asan_report_load4_noabort+0x18/0x20 [ 118.125566] meson_viu_set_osd_lut+0x7a0/0x890 [ 118.129953] meson_viu_init+0x10c/0x290 [ 118.133741] meson_drv_bind_master+0x474/0x748 [ 118.138141] meson_drv_bind+0x10/0x18 [ 118.141760] try_to_bring_up_master+0x3d8/0x768 [ 118.146249] component_add+0x214/0x570 [ 118.149978] meson_dw_hdmi_probe+0x18/0x20 [meson_dw_hdmi] [ 118.155404] platform_drv_probe+0x98/0x138 [ 118.159455] really_probe+0x2a0/0xa70 [ 118.163070] driver_probe_device+0x1b4/0x2d8 [ 118.167299] __driver_attach+0x200/0x280 [ 118.171189] bus_for_each_dev+0x10c/0x1a8 [ 118.175144] driver_attach+0x38/0x50 [ 118.178681] bus_add_driver+0x330/0x608 [ 118.182471] driver_register+0x140/0x388 [ 118.186361] __platform_driver_register+0xc8/0x108 [ 118.191117] meson_dw_hdmi_platform_driver_init+0x1c/0x1000 [meson_dw_hdmi] [ 118.198022] do_one_initcall+0x12c/0x3bc [ 118.201883] do_init_module+0x1fc/0x638 [ 118.205673] load_module+0x4b4c/0x6808 [ 118.209387] __se_sys_init_module+0x2e8/0x3c0 [ 118.213699] __arm64_sys_init_module+0x68/0x98 [ 118.218100] el0_svc_common+0x104/0x210 [ 118.221893] el0_svc_handler+0x48/0xb8 [ 118.225594] el0_svc+0x8/0xc [ 118.228429] [ 118.229887] The buggy address belongs to the variable: [ 118.235007] eotf_33_linear_mapping+0x84/0xc0 [ 118.239301] [ 118.240752] Memory state around the buggy address: [ 118.245522] ffff20000a63cd00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 118.252695] ffff20000a63cd80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 118.259850] >ffff20000a63ce00: 00 00 00 00 04 fa fa fa fa fa fa fa 00 00 00 00 [ 118.267000] ^ [ 118.271222] ffff20000a63ce80: 00 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00 [ 118.278393] ffff20000a63cf00: 00 00 00 00 00 00 00 00 00 00 00 00 04 fa fa fa [ 118.285542] ================================================================== [ 118.292699] Disabling lock debugging due to kernel taint It seems that when looping through the OSD EOTF LUT maps, we use the same max iterator for OETF: 20. This is wrong though, since 20*2 is 40, which means that we'll stop out of bounds on the EOTF maps. But, this whole thing is already confusing enough to read through as-is, so let's just replace all of the hardcoded sizes with OSD_(OETF/EOTF)_LUT_SIZE / 2. Signed-off-by: Lyude Paul <[email protected]> Fixes: bbbe775 ("drm: Add support for Amlogic Meson Graphic Controller") Cc: Neil Armstrong <[email protected]> Cc: Maxime Ripard <[email protected]> Cc: Carlo Caione <[email protected]> Cc: Kevin Hilman <[email protected]> Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: <[email protected]> # v4.10+ Acked-by: Neil Armstrong <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Signed-off-by: Sean Paul <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 36eb8ff upstream. Crash dump shows following instructions crash> bt PID: 0 TASK: ffffffffbe412480 CPU: 0 COMMAND: "swapper/0" #0 [ffff891ee0003868] machine_kexec at ffffffffbd063ef1 Freescale#1 [ffff891ee00038c8] __crash_kexec at ffffffffbd12b6f2 Freescale#2 [ffff891ee0003998] crash_kexec at ffffffffbd12c84c Freescale#3 [ffff891ee00039b8] oops_end at ffffffffbd030f0a Freescale#4 [ffff891ee00039e0] no_context at ffffffffbd074643 Freescale#5 [ffff891ee0003a40] __bad_area_nosemaphore at ffffffffbd07496e Freescale#6 [ffff891ee0003a90] bad_area_nosemaphore at ffffffffbd074a64 Freescale#7 [ffff891ee0003aa0] __do_page_fault at ffffffffbd074b0a Freescale#8 [ffff891ee0003b18] do_page_fault at ffffffffbd074fc8 Freescale#9 [ffff891ee0003b50] page_fault at ffffffffbda01925 [exception RIP: qlt_schedule_sess_for_deletion+15] RIP: ffffffffc02e526f RSP: ffff891ee0003c08 RFLAGS: 00010046 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffc0307847 RDX: 00000000000020e6 RSI: ffff891edbc377c8 RDI: 0000000000000000 RBP: ffff891ee0003c18 R8: ffffffffc02f0b20 R9: 0000000000000250 R10: 0000000000000258 R11: 000000000000b780 R12: ffff891ed9b43000 R13: 00000000000000f0 R14: 0000000000000006 R15: ffff891edbc377c8 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 Freescale#10 [ffff891ee0003c20] qla2x00_fcport_event_handler at ffffffffc02853d3 [qla2xxx] Freescale#11 [ffff891ee0003cf0] __dta_qla24xx_async_gnl_sp_done_333 at ffffffffc0285a1d [qla2xxx] Freescale#12 [ffff891ee0003de8] qla24xx_process_response_queue at ffffffffc02a2eb5 [qla2xxx] Freescale#13 [ffff891ee0003e88] qla24xx_msix_rsp_q at ffffffffc02a5403 [qla2xxx] Freescale#14 [ffff891ee0003ec0] __handle_irq_event_percpu at ffffffffbd0f4c59 Freescale#15 [ffff891ee0003f10] handle_irq_event_percpu at ffffffffbd0f4e02 Freescale#16 [ffff891ee0003f40] handle_irq_event at ffffffffbd0f4e90 Freescale#17 [ffff891ee0003f68] handle_edge_irq at ffffffffbd0f8984 Freescale#18 [ffff891ee0003f88] handle_irq at ffffffffbd0305d5 Freescale#19 [ffff891ee0003fb8] do_IRQ at ffffffffbda02a18 --- <IRQ stack> --- Freescale#20 [ffffffffbe403d30] ret_from_intr at ffffffffbda0094e [exception RIP: unknown or invalid address] RIP: 000000000000001f RSP: 0000000000000000 RFLAGS: fff3b8c2091ebb3f RAX: ffffbba5a0000200 RBX: 0000be8cdfa8f9fa RCX: 0000000000000018 RDX: 0000000000000101 RSI: 000000000000015d RDI: 0000000000000193 RBP: 0000000000000083 R8: ffffffffbe403e38 R9: 0000000000000002 R10: 0000000000000000 R11: ffffffffbe56b820 R12: ffff891ee001cf00 R13: ffffffffbd11c0a4 R14: ffffffffbe403d60 R15: 0000000000000001 ORIG_RAX: ffff891ee0022ac0 CS: 0000 SS: ffffffffffffffb9 bt: WARNING: possibly bogus exception frame Freescale#21 [ffffffffbe403dd8] cpuidle_enter_state at ffffffffbd67c6fd Freescale#22 [ffffffffbe403e40] cpuidle_enter at ffffffffbd67c907 Freescale#23 [ffffffffbe403e50] call_cpuidle at ffffffffbd0d98f3 Freescale#24 [ffffffffbe403e60] do_idle at ffffffffbd0d9b42 Freescale#25 [ffffffffbe403e98] cpu_startup_entry at ffffffffbd0d9da3 Freescale#26 [ffffffffbe403ec0] rest_init at ffffffffbd81d4aa Freescale#27 [ffffffffbe403ed0] start_kernel at ffffffffbe67d2ca Freescale#28 [ffffffffbe403f28] x86_64_start_reservations at ffffffffbe67c675 Freescale#29 [ffffffffbe403f38] x86_64_start_kernel at ffffffffbe67c6eb Freescale#30 [ffffffffbe403f50] secondary_startup_64 at ffffffffbd0000d5 Fixes: 040036b ("scsi: qla2xxx: Delay loop id allocation at login") Cc: <[email protected]> # v4.17+ Signed-off-by: Chuck Anderson <[email protected]> Signed-off-by: Himanshu Madhani <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 45caeaa ] As Eric Dumazet pointed out this also needs to be fixed in IPv6. v2: Contains the IPv6 tcp/Ipv6 dccp patches as well. We have seen a few incidents lately where a dst_enty has been freed with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that dst_entry. If the conditions/timings are right a crash then ensues when the freed dst_entry is referenced later on. A Common crashing back trace is: Freescale#8 [] page_fault at ffffffff8163e648 [exception RIP: __tcp_ack_snd_check+74] . . Freescale#9 [] tcp_rcv_established at ffffffff81580b64 Freescale#10 [] tcp_v4_do_rcv at ffffffff8158b54a Freescale#11 [] tcp_v4_rcv at ffffffff8158cd02 Freescale#12 [] ip_local_deliver_finish at ffffffff815668f4 Freescale#13 [] ip_local_deliver at ffffffff81566bd9 Freescale#14 [] ip_rcv_finish at ffffffff8156656d Freescale#15 [] ip_rcv at ffffffff81566f06 Freescale#16 [] __netif_receive_skb_core at ffffffff8152b3a2 Freescale#17 [] __netif_receive_skb at ffffffff8152b608 Freescale#18 [] netif_receive_skb at ffffffff8152b690 Freescale#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3] Freescale#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3] Freescale#21 [] net_rx_action at ffffffff8152bac2 Freescale#22 [] __do_softirq at ffffffff81084b4f Freescale#23 [] call_softirq at ffffffff8164845c Freescale#24 [] do_softirq at ffffffff81016fc5 Freescale#25 [] irq_exit at ffffffff81084ee5 Freescale#26 [] do_IRQ at ffffffff81648ff8 Of course it may happen with other NIC drivers as well. It's found the freed dst_entry here: 224 static bool tcp_in_quickack_mode(struct sock *sk)↩ 225 {↩ 226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩ 227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩ 228 ↩ 229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩ 230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩ 231 }↩ But there are other backtraces attributed to the same freed dst_entry in netfilter code as well. All the vmcores showed 2 significant clues: - Remote hosts behind the default gateway had always been redirected to a different gateway. A rtable/dst_entry will be added for that host. Making more dst_entrys with lower reference counts. Making this more probable. - All vmcores showed a postitive LockDroppedIcmps value, e.g: LockDroppedIcmps 267 A closer look at the tcp_v4_err() handler revealed that do_redirect() will run regardless of whether user space has the socket locked. This can result in a race condition where the same dst_entry cached in sk->sk_dst_entry can be decremented twice for the same socket via: do_redirect()->__sk_dst_check()-> dst_release(). Which leads to the dst_entry being prematurely freed with another socket pointing to it via sk->sk_dst_cache and a subsequent crash. To fix this skip do_redirect() if usespace has the socket locked. Instead let the redirect take place later when user space does not have the socket locked. The dccp/IPv6 code is very similar in this respect, so fixing it there too. As Eric Garver pointed out the following commit now invalidates routes. Which can set the dst->obsolete flag so that ipv4_dst_check() returns null and triggers the dst_release(). Fixes: ceb3320 ("ipv4: Kill routes during PMTU/redirect updates.") Cc: Eric Garver <[email protected]> Cc: Hannes Sowa <[email protected]> Signed-off-by: Jon Maxwell <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 6f48655 upstream. This patch fixes a generate_node_acls = 1 + cache_dynamic_acls = 0 regression, that was introduced by commit 01d4d67 Author: Nicholas Bellinger <[email protected]> Date: Wed Dec 7 12:55:54 2016 -0800 which originally had the proper list_del_init() usage, but was dropped during list review as it was thought unnecessary by HCH. However, list_del_init() usage is required during the special generate_node_acls = 1 + cache_dynamic_acls = 0 case when transport_free_session() does a list_del(&se_nacl->acl_list), followed by target_complete_nacl() doing the same thing. This was manifesting as a general protection fault as reported by Justin: kernel: general protection fault: 0000 [Freescale#1] SMP kernel: Modules linked in: kernel: CPU: 0 PID: 11047 Comm: iscsi_ttx Not tainted 4.13.0-rc2.x86_64.1+ Freescale#20 kernel: Hardware name: Intel Corporation S5500BC/S5500BC, BIOS S5500.86B.01.00.0064.050520141428 05/05/2014 kernel: task: ffff88026939e800 task.stack: ffffc90007884000 kernel: RIP: 0010:target_put_nacl+0x49/0xb0 kernel: RSP: 0018:ffffc90007887d70 EFLAGS: 00010246 kernel: RAX: dead000000000200 RBX: ffff8802556ca000 RCX: 0000000000000000 kernel: RDX: dead000000000100 RSI: 0000000000000246 RDI: ffff8802556ce028 kernel: RBP: ffffc90007887d88 R08: 0000000000000001 R09: 0000000000000000 kernel: R10: ffffc90007887df8 R11: ffffea0009986900 R12: ffff8802556ce020 kernel: R13: ffff8802556ce028 R14: ffff8802556ce028 R15: ffffffff88d85540 kernel: FS: 0000000000000000(0000) GS:ffff88027fc00000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00007fffe36f5f94 CR3: 0000000009209000 CR4: 00000000003406f0 kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 kernel: Call Trace: kernel: transport_free_session+0x67/0x140 kernel: transport_deregister_session+0x7a/0xc0 kernel: iscsit_close_session+0x92/0x210 kernel: iscsit_close_connection+0x5f9/0x840 kernel: iscsit_take_action_for_connection_exit+0xfe/0x110 kernel: iscsi_target_tx_thread+0x140/0x1e0 kernel: ? wait_woken+0x90/0x90 kernel: kthread+0x124/0x160 kernel: ? iscsit_thread_get_cpumask+0x90/0x90 kernel: ? kthread_create_on_node+0x40/0x40 kernel: ret_from_fork+0x22/0x30 kernel: Code: 00 48 89 fb 4c 8b a7 48 01 00 00 74 68 4d 8d 6c 24 08 4c 89 ef e8 e8 28 43 00 48 8b 93 20 04 00 00 48 8b 83 28 04 00 00 4c 89 ef <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 20 kernel: RIP: target_put_nacl+0x49/0xb0 RSP: ffffc90007887d70 kernel: ---[ end trace f12821adbfd46fed ]--- To address this, go ahead and use proper list_del_list() for all cases of se_nacl->acl_list deletion. Reported-by: Justin Maggard <[email protected]> Tested-by: Justin Maggard <[email protected]> Cc: Justin Maggard <[email protected]> Signed-off-by: Nicholas Bellinger <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 560d388 ] cifs_relock_file() can perform a down_write() on the inode's lock_sem even though it was already performed in cifs_strict_readv(). Lockdep complains about this. AFAICS, there is no problem here, and lockdep just needs to be told that this nesting is OK. ============================================= [ INFO: possible recursive locking detected ] 4.11.0+ #20 Not tainted --------------------------------------------- cat/701 is trying to acquire lock: (&cifsi->lock_sem){++++.+}, at: cifs_reopen_file+0x7a7/0xc00 but task is already holding lock: (&cifsi->lock_sem){++++.+}, at: cifs_strict_readv+0x177/0x310 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&cifsi->lock_sem); lock(&cifsi->lock_sem); *** DEADLOCK *** May be due to missing lock nesting notation 1 lock held by cat/701: #0: (&cifsi->lock_sem){++++.+}, at: cifs_strict_readv+0x177/0x310 stack backtrace: CPU: 0 PID: 701 Comm: cat Not tainted 4.11.0+ #20 Call Trace: dump_stack+0x85/0xc2 __lock_acquire+0x17dd/0x2260 ? trace_hardirqs_on_thunk+0x1a/0x1c ? preempt_schedule_irq+0x6b/0x80 lock_acquire+0xcc/0x260 ? lock_acquire+0xcc/0x260 ? cifs_reopen_file+0x7a7/0xc00 down_read+0x2d/0x70 ? cifs_reopen_file+0x7a7/0xc00 cifs_reopen_file+0x7a7/0xc00 ? printk+0x43/0x4b cifs_readpage_worker+0x327/0x8a0 cifs_readpage+0x8c/0x2a0 generic_file_read_iter+0x692/0xd00 cifs_strict_readv+0x29f/0x310 generic_file_splice_read+0x11c/0x1c0 do_splice_to+0xa5/0xc0 splice_direct_to_actor+0xfa/0x350 ? generic_pipe_buf_nosteal+0x10/0x10 do_splice_direct+0xb5/0xe0 do_sendfile+0x278/0x3a0 SyS_sendfile64+0xc4/0xe0 entry_SYSCALL_64_fastpath+0x1f/0xbe Signed-off-by: Rabin Vincent <[email protected]> Acked-by: Pavel Shilovsky <[email protected]> Signed-off-by: Steve French <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 46cc0b4 upstream. Current snapshot implementation swaps two ring_buffers even though their sizes are different from each other, that can cause an inconsistency between the contents of buffer_size_kb file and the current buffer size. For example: # cat buffer_size_kb 7 (expanded: 1408) # echo 1 > events/enable # grep bytes per_cpu/cpu0/stats bytes: 1441020 # echo 1 > snapshot // current:1408, spare:1408 # echo 123 > buffer_size_kb // current:123, spare:1408 # echo 1 > snapshot // current:1408, spare:123 # grep bytes per_cpu/cpu0/stats bytes: 1443700 # cat buffer_size_kb 123 // != current:1408 And also, a similar per-cpu case hits the following WARNING: Reproducer: # echo 1 > per_cpu/cpu0/snapshot # echo 123 > buffer_size_kb # echo 1 > per_cpu/cpu0/snapshot WARNING: WARNING: CPU: 0 PID: 1946 at kernel/trace/trace.c:1607 update_max_tr_single.part.0+0x2b8/0x380 Modules linked in: CPU: 0 PID: 1946 Comm: bash Not tainted 5.2.0-rc6 Freescale#20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014 RIP: 0010:update_max_tr_single.part.0+0x2b8/0x380 Code: ff e8 dc da f9 ff 0f 0b e9 88 fe ff ff e8 d0 da f9 ff 44 89 ee bf f5 ff ff ff e8 33 dc f9 ff 41 83 fd f5 74 96 e8 b8 da f9 ff <0f> 0b eb 8d e8 af da f9 ff 0f 0b e9 bf fd ff ff e8 a3 da f9 ff 48 RSP: 0018:ffff888063e4fca0 EFLAGS: 00010093 RAX: ffff888066214380 RBX: ffffffff99850fe0 RCX: ffffffff964298a8 RDX: 0000000000000000 RSI: 00000000fffffff5 RDI: 0000000000000005 RBP: 1ffff1100c7c9f96 R08: ffff888066214380 R09: ffffed100c7c9f9b R10: ffffed100c7c9f9a R11: 0000000000000003 R12: 0000000000000000 R13: 00000000ffffffea R14: ffff888066214380 R15: ffffffff99851060 FS: 00007f9f8173c700(0000) GS:ffff88806d000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000714dc0 CR3: 0000000066fa6000 CR4: 00000000000006f0 Call Trace: ? trace_array_printk_buf+0x140/0x140 ? __mutex_lock_slowpath+0x10/0x10 tracing_snapshot_write+0x4c8/0x7f0 ? trace_printk_init_buffers+0x60/0x60 ? selinux_file_permission+0x3b/0x540 ? tracer_preempt_off+0x38/0x506 ? trace_printk_init_buffers+0x60/0x60 __vfs_write+0x81/0x100 vfs_write+0x1e1/0x560 ksys_write+0x126/0x250 ? __ia32_sys_read+0xb0/0xb0 ? do_syscall_64+0x1f/0x390 do_syscall_64+0xc1/0x390 entry_SYSCALL_64_after_hwframe+0x49/0xbe This patch adds resize_buffer_duplicate_size() to check if there is a difference between current/spare buffer sizes and resize a spare buffer if necessary. Link: http://lkml.kernel.org/r/[email protected] Cc: [email protected] Fixes: ad909e2 ("tracing: Add internal tracing_snapshot() functions") Signed-off-by: Eiichi Tsukata <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit f9c6456 upstream. Masoud Sharbiani noticed that commit 29ef680 ("memcg, oom: move out_of_memory back to the charge path") broke memcg OOM called from __xfs_filemap_fault() path. It turned out that try_charge() is retrying forever without making forward progress because mem_cgroup_oom(GFP_NOFS) cannot invoke the OOM killer due to commit 3da88fb ("mm, oom: move GFP_NOFS check to out_of_memory"). Allowing forced charge due to being unable to invoke memcg OOM killer will lead to global OOM situation. Also, just returning -ENOMEM will be risky because OOM path is lost and some paths (e.g. get_user_pages()) will leak -ENOMEM. Therefore, invoking memcg OOM killer (despite GFP_NOFS) will be the only choice we can choose for now. Until 29ef680, we were able to invoke memcg OOM killer when GFP_KERNEL reclaim failed [1]. But since 29ef680, we need to invoke memcg OOM killer when GFP_NOFS reclaim failed [2]. Although in the past we did invoke memcg OOM killer for GFP_NOFS [3], we might get pre-mature memcg OOM reports due to this patch. [1] leaker invoked oom-killer: gfp_mask=0x6200ca(GFP_HIGHUSER_MOVABLE), nodemask=(null), order=0, oom_score_adj=0 CPU: 0 PID: 2746 Comm: leaker Not tainted 4.18.0+ Freescale#19 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/13/2018 Call Trace: dump_stack+0x63/0x88 dump_header+0x67/0x27a ? mem_cgroup_scan_tasks+0x91/0xf0 oom_kill_process+0x210/0x410 out_of_memory+0x10a/0x2c0 mem_cgroup_out_of_memory+0x46/0x80 mem_cgroup_oom_synchronize+0x2e4/0x310 ? high_work_func+0x20/0x20 pagefault_out_of_memory+0x31/0x76 mm_fault_error+0x55/0x115 ? handle_mm_fault+0xfd/0x220 __do_page_fault+0x433/0x4e0 do_page_fault+0x22/0x30 ? page_fault+0x8/0x30 page_fault+0x1e/0x30 RIP: 0033:0x4009f0 Code: 03 00 00 00 e8 71 fd ff ff 48 83 f8 ff 49 89 c6 74 74 48 89 c6 bf c0 0c 40 00 31 c0 e8 69 fd ff ff 45 85 ff 7e 21 31 c9 66 90 <41> 0f be 14 0e 01 d3 f7 c1 ff 0f 00 00 75 05 41 c6 04 0e 2a 48 83 RSP: 002b:00007ffe29ae96f0 EFLAGS: 00010206 RAX: 000000000000001b RBX: 0000000000000000 RCX: 0000000001ce1000 RDX: 0000000000000000 RSI: 000000007fffffe5 RDI: 0000000000000000 RBP: 000000000000000c R08: 0000000000000000 R09: 00007f94be09220d R10: 0000000000000002 R11: 0000000000000246 R12: 00000000000186a0 R13: 0000000000000003 R14: 00007f949d845000 R15: 0000000002800000 Task in /leaker killed as a result of limit of /leaker memory: usage 524288kB, limit 524288kB, failcnt 158965 memory+swap: usage 0kB, limit 9007199254740988kB, failcnt 0 kmem: usage 2016kB, limit 9007199254740988kB, failcnt 0 Memory cgroup stats for /leaker: cache:844KB rss:521136KB rss_huge:0KB shmem:0KB mapped_file:0KB dirty:132KB writeback:0KB inactive_anon:0KB active_anon:521224KB inactive_file:1012KB active_file:8KB unevictable:0KB Memory cgroup out of memory: Kill process 2746 (leaker) score 998 or sacrifice child Killed process 2746 (leaker) total-vm:536704kB, anon-rss:521176kB, file-rss:1208kB, shmem-rss:0kB oom_reaper: reaped process 2746 (leaker), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB [2] leaker invoked oom-killer: gfp_mask=0x600040(GFP_NOFS), nodemask=(null), order=0, oom_score_adj=0 CPU: 1 PID: 2746 Comm: leaker Not tainted 4.18.0+ Freescale#20 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/13/2018 Call Trace: dump_stack+0x63/0x88 dump_header+0x67/0x27a ? mem_cgroup_scan_tasks+0x91/0xf0 oom_kill_process+0x210/0x410 out_of_memory+0x109/0x2d0 mem_cgroup_out_of_memory+0x46/0x80 try_charge+0x58d/0x650 ? __radix_tree_replace+0x81/0x100 mem_cgroup_try_charge+0x7a/0x100 __add_to_page_cache_locked+0x92/0x180 add_to_page_cache_lru+0x4d/0xf0 iomap_readpages_actor+0xde/0x1b0 ? iomap_zero_range_actor+0x1d0/0x1d0 iomap_apply+0xaf/0x130 iomap_readpages+0x9f/0x150 ? iomap_zero_range_actor+0x1d0/0x1d0 xfs_vm_readpages+0x18/0x20 [xfs] read_pages+0x60/0x140 __do_page_cache_readahead+0x193/0x1b0 ondemand_readahead+0x16d/0x2c0 page_cache_async_readahead+0x9a/0xd0 filemap_fault+0x403/0x620 ? alloc_set_pte+0x12c/0x540 ? _cond_resched+0x14/0x30 __xfs_filemap_fault+0x66/0x180 [xfs] xfs_filemap_fault+0x27/0x30 [xfs] __do_fault+0x19/0x40 __handle_mm_fault+0x8e8/0xb60 handle_mm_fault+0xfd/0x220 __do_page_fault+0x238/0x4e0 do_page_fault+0x22/0x30 ? page_fault+0x8/0x30 page_fault+0x1e/0x30 RIP: 0033:0x4009f0 Code: 03 00 00 00 e8 71 fd ff ff 48 83 f8 ff 49 89 c6 74 74 48 89 c6 bf c0 0c 40 00 31 c0 e8 69 fd ff ff 45 85 ff 7e 21 31 c9 66 90 <41> 0f be 14 0e 01 d3 f7 c1 ff 0f 00 00 75 05 41 c6 04 0e 2a 48 83 RSP: 002b:00007ffda45c9290 EFLAGS: 00010206 RAX: 000000000000001b RBX: 0000000000000000 RCX: 0000000001a1e000 RDX: 0000000000000000 RSI: 000000007fffffe5 RDI: 0000000000000000 RBP: 000000000000000c R08: 0000000000000000 R09: 00007f6d061ff20d R10: 0000000000000002 R11: 0000000000000246 R12: 00000000000186a0 R13: 0000000000000003 R14: 00007f6ce59b2000 R15: 0000000002800000 Task in /leaker killed as a result of limit of /leaker memory: usage 524288kB, limit 524288kB, failcnt 7221 memory+swap: usage 0kB, limit 9007199254740988kB, failcnt 0 kmem: usage 1944kB, limit 9007199254740988kB, failcnt 0 Memory cgroup stats for /leaker: cache:3632KB rss:518232KB rss_huge:0KB shmem:0KB mapped_file:0KB dirty:0KB writeback:0KB inactive_anon:0KB active_anon:518408KB inactive_file:3908KB active_file:12KB unevictable:0KB Memory cgroup out of memory: Kill process 2746 (leaker) score 992 or sacrifice child Killed process 2746 (leaker) total-vm:536704kB, anon-rss:518264kB, file-rss:1188kB, shmem-rss:0kB oom_reaper: reaped process 2746 (leaker), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB [3] leaker invoked oom-killer: gfp_mask=0x50, order=0, oom_score_adj=0 leaker cpuset=/ mems_allowed=0 CPU: 1 PID: 3206 Comm: leaker Not tainted 3.10.0-957.27.2.el7.x86_64 Freescale#1 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/13/2018 Call Trace: [<ffffffffaf364147>] dump_stack+0x19/0x1b [<ffffffffaf35eb6a>] dump_header+0x90/0x229 [<ffffffffaedbb456>] ? find_lock_task_mm+0x56/0xc0 [<ffffffffaee32a38>] ? try_get_mem_cgroup_from_mm+0x28/0x60 [<ffffffffaedbb904>] oom_kill_process+0x254/0x3d0 [<ffffffffaee36c36>] mem_cgroup_oom_synchronize+0x546/0x570 [<ffffffffaee360b0>] ? mem_cgroup_charge_common+0xc0/0xc0 [<ffffffffaedbc194>] pagefault_out_of_memory+0x14/0x90 [<ffffffffaf35d072>] mm_fault_error+0x6a/0x157 [<ffffffffaf3717c8>] __do_page_fault+0x3c8/0x4f0 [<ffffffffaf371925>] do_page_fault+0x35/0x90 [<ffffffffaf36d768>] page_fault+0x28/0x30 Task in /leaker killed as a result of limit of /leaker memory: usage 524288kB, limit 524288kB, failcnt 20628 memory+swap: usage 524288kB, limit 9007199254740988kB, failcnt 0 kmem: usage 0kB, limit 9007199254740988kB, failcnt 0 Memory cgroup stats for /leaker: cache:840KB rss:523448KB rss_huge:0KB mapped_file:0KB swap:0KB inactive_anon:0KB active_anon:523448KB inactive_file:464KB active_file:376KB unevictable:0KB Memory cgroup out of memory: Kill process 3206 (leaker) score 970 or sacrifice child Killed process 3206 (leaker) total-vm:536692kB, anon-rss:523304kB, file-rss:412kB, shmem-rss:0kB Bisected by Masoud Sharbiani. Link: http://lkml.kernel.org/r/[email protected] Fixes: 3da88fb ("mm, oom: move GFP_NOFS check to out_of_memory") [necessary after 29ef680] Signed-off-by: Tetsuo Handa <[email protected]> Reported-by: Masoud Sharbiani <[email protected]> Tested-by: Masoud Sharbiani <[email protected]> Acked-by: Michal Hocko <[email protected]> Cc: David Rientjes <[email protected]> Cc: <[email protected]> [4.19+] Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 8659ab3 ] Warning log: [ 4.141392] Unexpected gfp: 0x4 (GFP_DMA32). Fixing up to gfp: 0xa20 (GFP_ATOMIC). Fix your code! [ 4.150340] CPU: 1 PID: 175 Comm: 1-0050 Not tainted 5.15.5-00039-g2fd9ae1b568c Freescale#20 [ 4.158010] Hardware name: Freescale i.MX8QXP MEK (DT) [ 4.163155] Call trace: [ 4.165600] dump_backtrace+0x0/0x1b0 [ 4.169286] show_stack+0x18/0x68 [ 4.172611] dump_stack_lvl+0x68/0x84 [ 4.176286] dump_stack+0x18/0x34 [ 4.179613] kmalloc_fix_flags+0x60/0x88 [ 4.183550] new_slab+0x334/0x370 [ 4.186878] ___slab_alloc.part.108+0x4d4/0x748 [ 4.191419] __slab_alloc.isra.109+0x30/0x78 [ 4.195702] kmem_cache_alloc+0x40c/0x420 [ 4.199725] dma_pool_alloc+0xac/0x1f8 [ 4.203486] cdns3_allocate_trb_pool+0xb4/0xd0 pool_alloc_page(struct dma_pool *pool, gfp_t mem_flags) { ... page = kmalloc(sizeof(*page), mem_flags); page->vaddr = dma_alloc_coherent(pool->dev, pool->allocation, &page->dma, mem_flags); ... } kmalloc was called with mem_flags, which is passed down in cdns3_allocate_trb_pool() and have GFP_DMA32 flags. kmall_fix_flags() report warning. GFP_DMA32 is not useful at all. dma_alloc_coherent() will handle DMA memory region correctly by pool->dev. GFP_DMA32 can be removed safely. Signed-off-by: Frank Li <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

Warning log: [ 4.141392] Unexpected gfp: 0x4 (GFP_DMA32). Fixing up to gfp: 0xa20 (GFP_ATOMIC). Fix your code! [ 4.150340] CPU: 1 PID: 175 Comm: 1-0050 Not tainted 5.15.5-00039-g2fd9ae1b568c #20 [ 4.158010] Hardware name: Freescale i.MX8QXP MEK (DT) [ 4.163155] Call trace: [ 4.165600] dump_backtrace+0x0/0x1b0 [ 4.169286] show_stack+0x18/0x68 [ 4.172611] dump_stack_lvl+0x68/0x84 [ 4.176286] dump_stack+0x18/0x34 [ 4.179613] kmalloc_fix_flags+0x60/0x88 [ 4.183550] new_slab+0x334/0x370 [ 4.186878] ___slab_alloc.part.108+0x4d4/0x748 [ 4.191419] __slab_alloc.isra.109+0x30/0x78 [ 4.195702] kmem_cache_alloc+0x40c/0x420 [ 4.199725] dma_pool_alloc+0xac/0x1f8 [ 4.203486] cdns3_allocate_trb_pool+0xb4/0xd0 pool_alloc_page(struct dma_pool *pool, gfp_t mem_flags) { ... page = kmalloc(sizeof(*page), mem_flags); page->vaddr = dma_alloc_coherent(pool->dev, pool->allocation, &page->dma, mem_flags); ... } kmalloc was called with mem_flags, which is passed down in cdns3_allocate_trb_pool() and have GFP_DMA32 flags. kmall_fix_flags() report warning. GFP_DMA32 is not useful at all. dma_alloc_coherent() will handle DMA memory region correctly by pool->dev. GFP_DMA32 can be removed safely. Signed-off-by: Frank Li <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

Warning ======= Running v5.13-rt1 on my arm64 Juno board triggers: [ 0.156302] ============================= [ 0.160416] WARNING: suspicious RCU usage [ 0.164529] 5.13.0-rt1 Freescale#20 Not tainted [ 0.168300] ----------------------------- [ 0.172409] kernel/rcu/tree_plugin.h:69 Unsafe read of RCU_NOCB offloaded state! [ 0.179920] [ 0.179920] other info that might help us debug this: [ 0.179920] [ 0.188037] [ 0.188037] rcu_scheduler_active = 1, debug_locks = 1 [ 0.194677] 3 locks held by rcuc/0/11: [ 0.198448] #0: ffff00097ef10cf8 ((softirq_ctrl.lock).lock){+.+.}-{2:2}, at: __local_bh_disable_ip (./include/linux/rcupdate.h:662 kernel/softirq.c:171) [ 0.208709] Freescale#1: ffff80001205e5f0 (rcu_read_lock){....}-{1:2}, at: rt_spin_lock (kernel/locking/spinlock_rt.c:43 (discriminator 4)) [ 0.217134] Freescale#2: ffff80001205e5f0 (rcu_read_lock){....}-{1:2}, at: __local_bh_disable_ip (kernel/softirq.c:169) [ 0.226428] [ 0.226428] stack backtrace: [ 0.230889] CPU: 0 PID: 11 Comm: rcuc/0 Not tainted 5.13.0-rt1 Freescale#20 [ 0.237100] Hardware name: ARM Juno development board (r0) (DT) [ 0.243041] Call trace: [ 0.245497] dump_backtrace (arch/arm64/kernel/stacktrace.c:163) [ 0.249185] show_stack (arch/arm64/kernel/stacktrace.c:219) [ 0.252522] dump_stack (lib/dump_stack.c:122) [ 0.255947] lockdep_rcu_suspicious (kernel/locking/lockdep.c:6439) [ 0.260328] rcu_rdp_is_offloaded (kernel/rcu/tree_plugin.h:69 kernel/rcu/tree_plugin.h:58) [ 0.264537] rcu_core (kernel/rcu/tree.c:2332 kernel/rcu/tree.c:2398 kernel/rcu/tree.c:2777) [ 0.267786] rcu_cpu_kthread (./include/linux/bottom_half.h:32 kernel/rcu/tree.c:2876) [ 0.271644] smpboot_thread_fn (kernel/smpboot.c:165 (discriminator 3)) [ 0.275767] kthread (kernel/kthread.c:321) [ 0.279013] ret_from_fork (arch/arm64/kernel/entry.S:1005) In this case, this is the RCU core kthread accessing the local CPU's rdp. Before that, rcu_cpu_kthread() invokes local_bh_disable(). Under !CONFIG_PREEMPT_RT (and rcutree.use_softirq=0), this ends up incrementing the preempt_count, which satisfies the "local non-preemptible read" of rcu_rdp_is_offloaded(). Under CONFIG_PREEMPT_RT however, this becomes local_lock(&softirq_ctrl.lock) which, under the same config, is migrate_disable() + rt_spin_lock(). As pointed out by Frederic, this is not sufficient to safely access an rdp's offload state, as the RCU core kthread can be preempted by a kworker executing rcu_nocb_rdp_offload() [1]. Introduce a local_lock to serialize an rdp's offload state while the rdp's associated core kthread is executing rcu_core(). rcu_core() preemptability considerations ======================================== As pointed out by Paul [2], keeping rcu_check_quiescent_state() preemptible (which is the case under CONFIG_PREEMPT_RT) requires some consideration. note_gp_changes() itself runs with irqs off, and enters __note_gp_changes() with rnp->lock held (raw_spinlock), thus is safe vs preemption. rdp->core_needs_qs *could* change after being read by the RCU core kthread if it then gets preempted. Consider, with CONFIG_RCU_STRICT_GRACE_PERIOD: rcuc/x task_foo rcu_check_quiescent_state() `\ rdp->core_needs_qs == true <PREEMPT> rcu_read_unlock() `\ rcu_preempt_deferred_qs_irqrestore() `\ rcu_report_qs_rdp() `\ rdp->core_needs_qs := false; This would let rcuc/x's rcu_check_quiescent_state() proceed further down to rcu_report_qs_rdp(), but if task_foo's earlier rcu_report_qs_rdp() invocation would have cleared the rdp grpmask from the rnp mask, so rcuc/x's invocation would simply bail. Since rcu_report_qs_rdp() can be safely invoked, even if rdp->core_needs_qs changed, it appears safe to keep rcu_check_quiescent_state() preemptible. [1]: http://lore.kernel.org/r/20210727230814.GC283787@lothringen [2]: http://lore.kernel.org/r/20210729010445.GO4397@paulmck-ThinkPad-P17-Gen-1 Signed-off-by: Valentin Schneider <[email protected]> Signed-off-by: Sebastian Andrzej Siewior <[email protected]> Link: https://lore.kernel.org/r/[email protected]

[ This is an all-in-one commit reverting the commit Revert "rcu/nocb: Protect NOCB state via local_lock() under PREEMPT_RT" and introducing this commit. ] Valentin reported warnings about suspicious RCU usage on RT kernels. Those happen when offloading of RCU callbacks is enabled: WARNING: suspicious RCU usage 5.13.0-rt1 Freescale#20 Not tainted ----------------------------- kernel/rcu/tree_plugin.h:69 Unsafe read of RCU_NOCB offloaded state! rcu_rdp_is_offloaded (kernel/rcu/tree_plugin.h:69 kernel/rcu/tree_plugin.h:58) rcu_core (kernel/rcu/tree.c:2332 kernel/rcu/tree.c:2398 kernel/rcu/tree.c:2777) rcu_cpu_kthread (./include/linux/bottom_half.h:32 kernel/rcu/tree.c:2876) The reason is that rcu_rdp_is_offloaded() is invoked without one of the required protections on RT enabled kernels because local_bh_disable() does not disable preemption on RT. Valentin proposed to add a local lock to the code in question, but that's suboptimal in several aspects: 1) local locks add extra code to !RT kernels for no value. 2) All possible callsites have to audited and amended when affected possible at an outer function level due to lock nesting issues. 3) As the local lock has to be taken at the outer functions it's required to release and reacquire them in the inner code sections which might voluntary schedule, e.g. rcu_do_batch(). Both callsites of rcu_rdp_is_offloaded() which trigger this check invoke rcu_rdp_is_offloaded() in the variable declaration section right at the top of the functions. But the actual usage of the result is either within a section which provides the required protections or after such a section. So the obvious solution is to move the invocation into the code sections which provide the proper protections, which solves the problem for RT and does not have any impact on !RT kernels. Reported-by: Valentin Schneider <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Signed-off-by: Sebastian Andrzej Siewior <[email protected]>

[ Upstream commit 4e264be ] When a system with E810 with existing VFs gets rebooted the following hang may be observed. Pid 1 is hung in iavf_remove(), part of a network driver: PID: 1 TASK: ffff965400e5a340 CPU: 24 COMMAND: "systemd-shutdow" #0 [ffffaad04005fa50] __schedule at ffffffff8b3239cb #1 [ffffaad04005fae8] schedule at ffffffff8b323e2d #2 [ffffaad04005fb00] schedule_hrtimeout_range_clock at ffffffff8b32cebc #3 [ffffaad04005fb80] usleep_range_state at ffffffff8b32c930 #4 [ffffaad04005fbb0] iavf_remove at ffffffffc12b9b4c [iavf] #5 [ffffaad04005fbf0] pci_device_remove at ffffffff8add7513 #6 [ffffaad04005fc10] device_release_driver_internal at ffffffff8af08baa #7 [ffffaad04005fc40] pci_stop_bus_device at ffffffff8adcc5fc #8 [ffffaad04005fc60] pci_stop_and_remove_bus_device at ffffffff8adcc81e #9 [ffffaad04005fc70] pci_iov_remove_virtfn at ffffffff8adf9429 #10 [ffffaad04005fca8] sriov_disable at ffffffff8adf98e4 #11 [ffffaad04005fcc8] ice_free_vfs at ffffffffc04bb2c8 [ice] #12 [ffffaad04005fd10] ice_remove at ffffffffc04778fe [ice] #13 [ffffaad04005fd38] ice_shutdown at ffffffffc0477946 [ice] #14 [ffffaad04005fd50] pci_device_shutdown at ffffffff8add58f1 #15 [ffffaad04005fd70] device_shutdown at ffffffff8af05386 #16 [ffffaad04005fd98] kernel_restart at ffffffff8a92a870 #17 [ffffaad04005fda8] __do_sys_reboot at ffffffff8a92abd6 #18 [ffffaad04005fee0] do_syscall_64 at ffffffff8b317159 #19 [ffffaad04005ff08] __context_tracking_enter at ffffffff8b31b6fc #20 [ffffaad04005ff18] syscall_exit_to_user_mode at ffffffff8b31b50d #21 [ffffaad04005ff28] do_syscall_64 at ffffffff8b317169 #22 [ffffaad04005ff50] entry_SYSCALL_64_after_hwframe at ffffffff8b40009b RIP: 00007f1baa5c13d7 RSP: 00007fffbcc55a98 RFLAGS: 00000202 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1baa5c13d7 RDX: 0000000001234567 RSI: 0000000028121969 RDI: 00000000fee1dead RBP: 00007fffbcc55ca0 R8: 0000000000000000 R9: 00007fffbcc54e90 R10: 00007fffbcc55050 R11: 0000000000000202 R12: 0000000000000005 R13: 0000000000000000 R14: 00007fffbcc55af0 R15: 0000000000000000 ORIG_RAX: 00000000000000a9 CS: 0033 SS: 002b During reboot all drivers PM shutdown callbacks are invoked. In iavf_shutdown() the adapter state is changed to __IAVF_REMOVE. In ice_shutdown() the call chain above is executed, which at some point calls iavf_remove(). However iavf_remove() expects the VF to be in one of the states __IAVF_RUNNING, __IAVF_DOWN or __IAVF_INIT_FAILED. If that's not the case it sleeps forever. So if iavf_shutdown() gets invoked before iavf_remove() the system will hang indefinitely because the adapter is already in state __IAVF_REMOVE. Fix this by returning from iavf_remove() if the state is __IAVF_REMOVE, as we already went through iavf_shutdown(). Fixes: 9745780 ("iavf: Add waiting so the port is initialized in remove") Fixes: a841733 ("iavf: Fix race condition between iavf_shutdown and iavf_remove") Reported-by: Marius Cornea <[email protected]> Signed-off-by: Stefan Assmann <[email protected]> Reviewed-by: Michal Kubiak <[email protected]> Tested-by: Rafal Romanowski <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 4e264be ] When a system with E810 with existing VFs gets rebooted the following hang may be observed. Pid 1 is hung in iavf_remove(), part of a network driver: PID: 1 TASK: ffff965400e5a340 CPU: 24 COMMAND: "systemd-shutdow" #0 [ffffaad04005fa50] __schedule at ffffffff8b3239cb Freescale#1 [ffffaad04005fae8] schedule at ffffffff8b323e2d Freescale#2 [ffffaad04005fb00] schedule_hrtimeout_range_clock at ffffffff8b32cebc Freescale#3 [ffffaad04005fb80] usleep_range_state at ffffffff8b32c930 Freescale#4 [ffffaad04005fbb0] iavf_remove at ffffffffc12b9b4c [iavf] Freescale#5 [ffffaad04005fbf0] pci_device_remove at ffffffff8add7513 Freescale#6 [ffffaad04005fc10] device_release_driver_internal at ffffffff8af08baa Freescale#7 [ffffaad04005fc40] pci_stop_bus_device at ffffffff8adcc5fc Freescale#8 [ffffaad04005fc60] pci_stop_and_remove_bus_device at ffffffff8adcc81e Freescale#9 [ffffaad04005fc70] pci_iov_remove_virtfn at ffffffff8adf9429 Freescale#10 [ffffaad04005fca8] sriov_disable at ffffffff8adf98e4 Freescale#11 [ffffaad04005fcc8] ice_free_vfs at ffffffffc04bb2c8 [ice] Freescale#12 [ffffaad04005fd10] ice_remove at ffffffffc04778fe [ice] Freescale#13 [ffffaad04005fd38] ice_shutdown at ffffffffc0477946 [ice] Freescale#14 [ffffaad04005fd50] pci_device_shutdown at ffffffff8add58f1 Freescale#15 [ffffaad04005fd70] device_shutdown at ffffffff8af05386 Freescale#16 [ffffaad04005fd98] kernel_restart at ffffffff8a92a870 Freescale#17 [ffffaad04005fda8] __do_sys_reboot at ffffffff8a92abd6 Freescale#18 [ffffaad04005fee0] do_syscall_64 at ffffffff8b317159 Freescale#19 [ffffaad04005ff08] __context_tracking_enter at ffffffff8b31b6fc Freescale#20 [ffffaad04005ff18] syscall_exit_to_user_mode at ffffffff8b31b50d Freescale#21 [ffffaad04005ff28] do_syscall_64 at ffffffff8b317169 Freescale#22 [ffffaad04005ff50] entry_SYSCALL_64_after_hwframe at ffffffff8b40009b RIP: 00007f1baa5c13d7 RSP: 00007fffbcc55a98 RFLAGS: 00000202 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1baa5c13d7 RDX: 0000000001234567 RSI: 0000000028121969 RDI: 00000000fee1dead RBP: 00007fffbcc55ca0 R8: 0000000000000000 R9: 00007fffbcc54e90 R10: 00007fffbcc55050 R11: 0000000000000202 R12: 0000000000000005 R13: 0000000000000000 R14: 00007fffbcc55af0 R15: 0000000000000000 ORIG_RAX: 00000000000000a9 CS: 0033 SS: 002b During reboot all drivers PM shutdown callbacks are invoked. In iavf_shutdown() the adapter state is changed to __IAVF_REMOVE. In ice_shutdown() the call chain above is executed, which at some point calls iavf_remove(). However iavf_remove() expects the VF to be in one of the states __IAVF_RUNNING, __IAVF_DOWN or __IAVF_INIT_FAILED. If that's not the case it sleeps forever. So if iavf_shutdown() gets invoked before iavf_remove() the system will hang indefinitely because the adapter is already in state __IAVF_REMOVE. Fix this by returning from iavf_remove() if the state is __IAVF_REMOVE, as we already went through iavf_shutdown(). Fixes: 9745780 ("iavf: Add waiting so the port is initialized in remove") Fixes: a841733 ("iavf: Fix race condition between iavf_shutdown and iavf_remove") Reported-by: Marius Cornea <[email protected]> Signed-off-by: Stefan Assmann <[email protected]> Reviewed-by: Michal Kubiak <[email protected]> Tested-by: Rafal Romanowski <[email protected]> Signed-off-by: Tony Nguyen <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

…_write() [ Upstream commit 2d1e952 ] If a user can make copy_from_user() fail, there is a potential for UAF/DF due to a lack of locking around the allocation, use and freeing of the data buffers. This issue is not theoretical. I managed to author a POC for it: BUG: KASAN: double-free in kfree+0x5c/0xac Free of addr ffff29280be5de00 by task poc/356 CPU: 1 PID: 356 Comm: poc Not tainted 6.1.0-00001-g961aa6552c04-dirty Freescale#20 Hardware name: linux,dummy-virt (DT) Call trace: dump_backtrace.part.0+0xe0/0xf0 show_stack+0x18/0x40 dump_stack_lvl+0x64/0x80 print_report+0x188/0x48c kasan_report_invalid_free+0xa0/0xc0 ____kasan_slab_free+0x174/0x1b0 __kasan_slab_free+0x18/0x24 __kmem_cache_free+0x130/0x2e0 kfree+0x5c/0xac mbox_test_message_write+0x208/0x29c full_proxy_write+0x90/0xf0 vfs_write+0x154/0x440 ksys_write+0xcc/0x180 __arm64_sys_write+0x44/0x60 invoke_syscall+0x60/0x190 el0_svc_common.constprop.0+0x7c/0x160 do_el0_svc+0x40/0xf0 el0_svc+0x2c/0x6c el0t_64_sync_handler+0xf4/0x120 el0t_64_sync+0x18c/0x190 Allocated by task 356: kasan_save_stack+0x3c/0x70 kasan_set_track+0x2c/0x40 kasan_save_alloc_info+0x24/0x34 __kasan_kmalloc+0xb8/0xc0 kmalloc_trace+0x58/0x70 mbox_test_message_write+0x6c/0x29c full_proxy_write+0x90/0xf0 vfs_write+0x154/0x440 ksys_write+0xcc/0x180 __arm64_sys_write+0x44/0x60 invoke_syscall+0x60/0x190 el0_svc_common.constprop.0+0x7c/0x160 do_el0_svc+0x40/0xf0 el0_svc+0x2c/0x6c el0t_64_sync_handler+0xf4/0x120 el0t_64_sync+0x18c/0x190 Freed by task 357: kasan_save_stack+0x3c/0x70 kasan_set_track+0x2c/0x40 kasan_save_free_info+0x38/0x5c ____kasan_slab_free+0x13c/0x1b0 __kasan_slab_free+0x18/0x24 __kmem_cache_free+0x130/0x2e0 kfree+0x5c/0xac mbox_test_message_write+0x208/0x29c full_proxy_write+0x90/0xf0 vfs_write+0x154/0x440 ksys_write+0xcc/0x180 __arm64_sys_write+0x44/0x60 invoke_syscall+0x60/0x190 el0_svc_common.constprop.0+0x7c/0x160 do_el0_svc+0x40/0xf0 el0_svc+0x2c/0x6c el0t_64_sync_handler+0xf4/0x120 el0t_64_sync+0x18c/0x190 Signed-off-by: Lee Jones <[email protected]> Signed-off-by: Jassi Brar <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit 0ad529d upstream. Christoph reported a divide by zero bug in mptcp_recvmsg(): divide error: 0000 [Freescale#1] PREEMPT SMP CPU: 1 PID: 19978 Comm: syz-executor.6 Not tainted 6.4.0-rc2-gffcc7899081b Freescale#20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014 RIP: 0010:__tcp_select_window+0x30e/0x420 net/ipv4/tcp_output.c:3018 Code: 11 ff 0f b7 cd c1 e9 0c b8 ff ff ff ff d3 e0 89 c1 f7 d1 01 cb 21 c3 eb 17 e8 2e 83 11 ff 31 db eb 0e e8 25 83 11 ff 89 d8 99 <f7> 7c 24 04 29 d3 65 48 8b 04 25 28 00 00 00 48 3b 44 24 10 75 60 RSP: 0018:ffffc90000a07a18 EFLAGS: 00010246 RAX: 000000000000ffd7 RBX: 000000000000ffd7 RCX: 0000000000040000 RDX: 0000000000000000 RSI: 000000000003ffff RDI: 0000000000040000 RBP: 000000000000ffd7 R08: ffffffff820cf297 R09: 0000000000000001 R10: 0000000000000000 R11: ffffffff8103d1a0 R12: 0000000000003f00 R13: 0000000000300000 R14: ffff888101cf3540 R15: 0000000000180000 FS: 00007f9af4c09640(0000) GS:ffff88813bd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b33824000 CR3: 000000012f241001 CR4: 0000000000170ee0 Call Trace: <TASK> __tcp_cleanup_rbuf+0x138/0x1d0 net/ipv4/tcp.c:1611 mptcp_recvmsg+0xcb8/0xdd0 net/mptcp/protocol.c:2034 inet_recvmsg+0x127/0x1f0 net/ipv4/af_inet.c:861 ____sys_recvmsg+0x269/0x2b0 net/socket.c:1019 ___sys_recvmsg+0xe6/0x260 net/socket.c:2764 do_recvmmsg+0x1a5/0x470 net/socket.c:2858 __do_sys_recvmmsg net/socket.c:2937 [inline] __se_sys_recvmmsg net/socket.c:2953 [inline] __x64_sys_recvmmsg+0xa6/0x130 net/socket.c:2953 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x47/0xa0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7f9af58fc6a9 Code: 5c c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 4f 37 0d 00 f7 d8 64 89 01 48 RSP: 002b:00007f9af4c08cd8 EFLAGS: 00000246 ORIG_RAX: 000000000000012b RAX: ffffffffffffffda RBX: 00000000006bc050 RCX: 00007f9af58fc6a9 RDX: 0000000000000001 RSI: 0000000020000140 RDI: 0000000000000004 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000f00 R11: 0000000000000246 R12: 00000000006bc05c R13: fffffffffffffea8 R14: 00000000006bc050 R15: 000000000001fe40 </TASK> mptcp_recvmsg is allowed to release the msk socket lock when blocking, and before re-acquiring it another thread could have switched the sock to TCP_LISTEN status - with a prior connect(AF_UNSPEC) - also clearing icsk_ack.rcv_mss. Address the issue preventing the disconnect if some other process is concurrently performing a blocking syscall on the same socket, alike commit 4faeee0 ("tcp: deny tcp_disconnect() when threads are waiting"). Fixes: a6b118f ("mptcp: add receive buffer auto-tuning") Cc: [email protected] Reported-by: Christoph Paasch <[email protected]> Closes: multipath-tcp/mptcp_net-next#404 Signed-off-by: Paolo Abeni <[email protected]> Tested-by: Christoph Paasch <[email protected]> Reviewed-by: Matthieu Baerts <[email protected]> Signed-off-by: Matthieu Baerts <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

Compat mode (CONFIG_COMPAT) allows application binaries built for a 32bit architecture to issue system calls to a 64bit kernel which implements such compatibility support. This work builds on the y2038 sanitization which eliminated the remaining assumptions about the size of native long integers in the same move. Although these changes enable armv7 binaries to call an armv8 kernel, most of them are architecture-independent, and follow this pattern: - .compat_ioctl and .compat_oob_ioctl handlers are added to all file operations structs, pointing at compat_ptr_ioctl() compat_ptr_oob_ioctl() respectively. - all pointers passed by applications within ioctl() argument structs are conveyed as generic 64bit values. These changes mandate upgrading the ABI revision to Freescale#20. Signed-off-by: Philippe Gerum <[email protected]>

commit 0b0747d upstream. The following processes run into a deadlock. CPU 41 was waiting for CPU 29 to handle a CSD request while holding spinlock "crashdump_lock", but CPU 29 was hung by that spinlock with IRQs disabled. PID: 17360 TASK: ffff95c1090c5c40 CPU: 41 COMMAND: "mrdiagd" !# 0 [ffffb80edbf37b58] __read_once_size at ffffffff9b871a40 include/linux/compiler.h:185:0 !# 1 [ffffb80edbf37b58] atomic_read at ffffffff9b871a40 arch/x86/include/asm/atomic.h:27:0 !# 2 [ffffb80edbf37b58] dump_stack at ffffffff9b871a40 lib/dump_stack.c:54:0 # 3 [ffffb80edbf37b78] csd_lock_wait_toolong at ffffffff9b131ad5 kernel/smp.c:364:0 # 4 [ffffb80edbf37b78] __csd_lock_wait at ffffffff9b131ad5 kernel/smp.c:384:0 # 5 [ffffb80edbf37bf8] csd_lock_wait at ffffffff9b13267a kernel/smp.c:394:0 # 6 [ffffb80edbf37bf8] smp_call_function_many at ffffffff9b13267a kernel/smp.c:843:0 # 7 [ffffb80edbf37c50] smp_call_function at ffffffff9b13279d kernel/smp.c:867:0 # 8 [ffffb80edbf37c50] on_each_cpu at ffffffff9b13279d kernel/smp.c:976:0 # 9 [ffffb80edbf37c78] flush_tlb_kernel_range at ffffffff9b085c4b arch/x86/mm/tlb.c:742:0 Freescale#10 [ffffb80edbf37cb8] __purge_vmap_area_lazy at ffffffff9b23a1e0 mm/vmalloc.c:701:0 Freescale#11 [ffffb80edbf37ce0] try_purge_vmap_area_lazy at ffffffff9b23a2cc mm/vmalloc.c:722:0 Freescale#12 [ffffb80edbf37ce0] free_vmap_area_noflush at ffffffff9b23a2cc mm/vmalloc.c:754:0 Freescale#13 [ffffb80edbf37cf8] free_unmap_vmap_area at ffffffff9b23bb3b mm/vmalloc.c:764:0 Freescale#14 [ffffb80edbf37cf8] remove_vm_area at ffffffff9b23bb3b mm/vmalloc.c:1509:0 Freescale#15 [ffffb80edbf37d18] __vunmap at ffffffff9b23bb8a mm/vmalloc.c:1537:0 Freescale#16 [ffffb80edbf37d40] vfree at ffffffff9b23bc85 mm/vmalloc.c:1612:0 Freescale#17 [ffffb80edbf37d58] megasas_free_host_crash_buffer [megaraid_sas] at ffffffffc020b7f2 drivers/scsi/megaraid/megaraid_sas_fusion.c:3932:0 Freescale#18 [ffffb80edbf37d80] fw_crash_state_store [megaraid_sas] at ffffffffc01f804d drivers/scsi/megaraid/megaraid_sas_base.c:3291:0 Freescale#19 [ffffb80edbf37dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 Freescale#20 [ffffb80edbf37dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 Freescale#21 [ffffb80edbf37de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 Freescale#22 [ffffb80edbf37e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 Freescale#23 [ffffb80edbf37ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 Freescale#24 [ffffb80edbf37ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 Freescale#25 [ffffb80edbf37ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 Freescale#26 [ffffb80edbf37f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 Freescale#27 [ffffb80edbf37f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 PID: 17355 TASK: ffff95c1090c3d80 CPU: 29 COMMAND: "mrdiagd" !# 0 [ffffb80f2d3c7d30] __read_once_size at ffffffff9b0f2ab0 include/linux/compiler.h:185:0 !# 1 [ffffb80f2d3c7d30] native_queued_spin_lock_slowpath at ffffffff9b0f2ab0 kernel/locking/qspinlock.c:368:0 # 2 [ffffb80f2d3c7d58] pv_queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/paravirt.h:674:0 # 3 [ffffb80f2d3c7d58] queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/qspinlock.h:53:0 # 4 [ffffb80f2d3c7d68] queued_spin_lock at ffffffff9b8961a6 include/asm-generic/qspinlock.h:90:0 # 5 [ffffb80f2d3c7d68] do_raw_spin_lock_flags at ffffffff9b8961a6 include/linux/spinlock.h:173:0 # 6 [ffffb80f2d3c7d68] __raw_spin_lock_irqsave at ffffffff9b8961a6 include/linux/spinlock_api_smp.h:122:0 # 7 [ffffb80f2d3c7d68] _raw_spin_lock_irqsave at ffffffff9b8961a6 kernel/locking/spinlock.c:160:0 # 8 [ffffb80f2d3c7d88] fw_crash_buffer_store [megaraid_sas] at ffffffffc01f8129 drivers/scsi/megaraid/megaraid_sas_base.c:3205:0 # 9 [ffffb80f2d3c7dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 Freescale#10 [ffffb80f2d3c7dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 Freescale#11 [ffffb80f2d3c7de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 Freescale#12 [ffffb80f2d3c7e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 Freescale#13 [ffffb80f2d3c7ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 Freescale#14 [ffffb80f2d3c7ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 Freescale#15 [ffffb80f2d3c7ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 Freescale#16 [ffffb80f2d3c7f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 Freescale#17 [ffffb80f2d3c7f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 The lock is used to synchronize different sysfs operations, it doesn't protect any resource that will be touched by an interrupt. Consequently it's not required to disable IRQs. Replace the spinlock with a mutex to fix the deadlock. Signed-off-by: Junxiao Bi <[email protected]> Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Mike Christie <[email protected]> Cc: [email protected] Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit c777b11 ] Inject fault while probing mdpy.ko, if kstrdup() of create_dir() fails in kobject_add_internal() in kobject_init_and_add() in mdev_type_add() in parent_create_sysfs_files(), it will return 0 and probe successfully. And when rmmod mdpy.ko, the mdpy_dev_exit() will call mdev_unregister_parent(), the mdev_type_remove() may traverse uninitialized parent->types[i] in parent_remove_sysfs_files(), and it will cause below null-ptr-deref. If mdev_type_add() fails, return the error code and kset_unregister() to fix the issue. general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [Freescale#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 2 PID: 10215 Comm: rmmod Tainted: G W N 6.6.0-rc2+ Freescale#20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:__kobject_del+0x62/0x1c0 Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 51 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 8b 6b 28 48 8d 7d 10 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 24 01 00 00 48 8b 75 10 48 89 df 48 8d 6b 3c e8 RSP: 0018:ffff88810695fd30 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: ffffffffa0270268 RCX: 0000000000000000 RDX: 0000000000000002 RSI: 0000000000000004 RDI: 0000000000000010 RBP: 0000000000000000 R08: 0000000000000001 R09: ffffed10233a4ef1 R10: ffff888119d2778b R11: 0000000063666572 R12: 0000000000000000 R13: fffffbfff404e2d4 R14: dffffc0000000000 R15: ffffffffa0271660 FS: 00007fbc81981540(0000) GS:ffff888119d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc14a142dc0 CR3: 0000000110a62003 CR4: 0000000000770ee0 DR0: ffffffff8fb0bce8 DR1: ffffffff8fb0bce9 DR2: ffffffff8fb0bcea DR3: ffffffff8fb0bceb DR6: 00000000fffe0ff0 DR7: 0000000000000600 PKRU: 55555554 Call Trace: <TASK> ? die_addr+0x3d/0xa0 ? exc_general_protection+0x144/0x220 ? asm_exc_general_protection+0x22/0x30 ? __kobject_del+0x62/0x1c0 kobject_del+0x32/0x50 parent_remove_sysfs_files+0xd6/0x170 [mdev] mdev_unregister_parent+0xfb/0x190 [mdev] ? mdev_register_parent+0x270/0x270 [mdev] ? find_module_all+0x9d/0xe0 mdpy_dev_exit+0x17/0x63 [mdpy] __do_sys_delete_module.constprop.0+0x2fa/0x4b0 ? module_flags+0x300/0x300 ? __fput+0x4e7/0xa00 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7fbc813221b7 Code: 73 01 c3 48 8b 0d d1 8c 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a1 8c 2c 00 f7 d8 64 89 01 48 RSP: 002b:00007ffe780e0648 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 RAX: ffffffffffffffda RBX: 00007ffe780e06a8 RCX: 00007fbc813221b7 RDX: 000000000000000a RSI: 0000000000000800 RDI: 000055e214df9b58 RBP: 000055e214df9af0 R08: 00007ffe780df5c1 R09: 0000000000000000 R10: 00007fbc8139ecc0 R11: 0000000000000206 R12: 00007ffe780e0870 R13: 00007ffe780e0ed0 R14: 000055e214df9260 R15: 000055e214df9af0 </TASK> Modules linked in: mdpy(-) mdev vfio_iommu_type1 vfio [last unloaded: mdpy] Dumping ftrace buffer: (ftrace buffer empty) ---[ end trace 0000000000000000 ]--- RIP: 0010:__kobject_del+0x62/0x1c0 Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 51 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 8b 6b 28 48 8d 7d 10 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 24 01 00 00 48 8b 75 10 48 89 df 48 8d 6b 3c e8 RSP: 0018:ffff88810695fd30 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: ffffffffa0270268 RCX: 0000000000000000 RDX: 0000000000000002 RSI: 0000000000000004 RDI: 0000000000000010 RBP: 0000000000000000 R08: 0000000000000001 R09: ffffed10233a4ef1 R10: ffff888119d2778b R11: 0000000063666572 R12: 0000000000000000 R13: fffffbfff404e2d4 R14: dffffc0000000000 R15: ffffffffa0271660 FS: 00007fbc81981540(0000) GS:ffff888119d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc14a142dc0 CR3: 0000000110a62003 CR4: 0000000000770ee0 DR0: ffffffff8fb0bce8 DR1: ffffffff8fb0bce9 DR2: ffffffff8fb0bcea DR3: ffffffff8fb0bceb DR6: 00000000fffe0ff0 DR7: 0000000000000600 PKRU: 55555554 Kernel panic - not syncing: Fatal exception Dumping ftrace buffer: (ftrace buffer empty) Kernel Offset: disabled Rebooting in 1 seconds.. Fixes: da44c34 ("vfio/mdev: simplify mdev_type handling") Signed-off-by: Jinjie Ruan <[email protected]> Reviewed-by: Eric Farman <[email protected]> Reviewed-by: Jason Gunthorpe <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Alex Williamson <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit a154f5f ] The following call trace shows a deadlock issue due to recursive locking of mutex "device_mutex". First lock acquire is in target_for_each_device() and second in target_free_device(). PID: 148266 TASK: ffff8be21ffb5d00 CPU: 10 COMMAND: "iscsi_ttx" #0 [ffffa2bfc9ec3b18] __schedule at ffffffffa8060e7f Freescale#1 [ffffa2bfc9ec3ba0] schedule at ffffffffa8061224 Freescale#2 [ffffa2bfc9ec3bb8] schedule_preempt_disabled at ffffffffa80615ee Freescale#3 [ffffa2bfc9ec3bc8] __mutex_lock at ffffffffa8062fd7 Freescale#4 [ffffa2bfc9ec3c40] __mutex_lock_slowpath at ffffffffa80631d3 Freescale#5 [ffffa2bfc9ec3c50] mutex_lock at ffffffffa806320c Freescale#6 [ffffa2bfc9ec3c68] target_free_device at ffffffffc0935998 [target_core_mod] Freescale#7 [ffffa2bfc9ec3c90] target_core_dev_release at ffffffffc092f975 [target_core_mod] Freescale#8 [ffffa2bfc9ec3ca0] config_item_put at ffffffffa79d250f Freescale#9 [ffffa2bfc9ec3cd0] config_item_put at ffffffffa79d2583 Freescale#10 [ffffa2bfc9ec3ce0] target_devices_idr_iter at ffffffffc0933f3a [target_core_mod] Freescale#11 [ffffa2bfc9ec3d00] idr_for_each at ffffffffa803f6fc Freescale#12 [ffffa2bfc9ec3d60] target_for_each_device at ffffffffc0935670 [target_core_mod] Freescale#13 [ffffa2bfc9ec3d98] transport_deregister_session at ffffffffc0946408 [target_core_mod] Freescale#14 [ffffa2bfc9ec3dc8] iscsit_close_session at ffffffffc09a44a6 [iscsi_target_mod] Freescale#15 [ffffa2bfc9ec3df0] iscsit_close_connection at ffffffffc09a4a88 [iscsi_target_mod] Freescale#16 [ffffa2bfc9ec3df8] finish_task_switch at ffffffffa76e5d07 Freescale#17 [ffffa2bfc9ec3e78] iscsit_take_action_for_connection_exit at ffffffffc0991c23 [iscsi_target_mod] Freescale#18 [ffffa2bfc9ec3ea0] iscsi_target_tx_thread at ffffffffc09a403b [iscsi_target_mod] Freescale#19 [ffffa2bfc9ec3f08] kthread at ffffffffa76d8080 Freescale#20 [ffffa2bfc9ec3f50] ret_from_fork at ffffffffa8200364 Fixes: 36d4cb4 ("scsi: target: Avoid that EXTENDED COPY commands trigger lock inversion") Signed-off-by: Junxiao Bi <[email protected]> Link: https://lore.kernel.org/r/[email protected] Reviewed-by: Mike Christie <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

According to SPF-55129 A2, the reset pin is #12 from pcal6524, and the WiFi regulator(M2_nDIS1) is #20 from pcal6524. Both indexes start from 0 here. Signed-off-by: Shenwei Wang <[email protected]> Reviewed-by: Frank Li <[email protected]>

[ Upstream commit e3e82fc ] When creating ceq_0 during probing irdma, cqp.sc_cqp will be sent as a cqp_request to cqp->sc_cqp.sq_ring. If the request is pending when removing the irdma driver or unplugging its aux device, cqp.sc_cqp will be dereferenced as wrong struct in irdma_free_pending_cqp_request(). PID: 3669 TASK: ffff88aef892c000 CPU: 28 COMMAND: "kworker/28:0" #0 [fffffe0000549e38] crash_nmi_callback at ffffffff810e3a34 Freescale#1 [fffffe0000549e40] nmi_handle at ffffffff810788b2 Freescale#2 [fffffe0000549ea0] default_do_nmi at ffffffff8107938f Freescale#3 [fffffe0000549eb8] do_nmi at ffffffff81079582 Freescale#4 [fffffe0000549ef0] end_repeat_nmi at ffffffff82e016b4 [exception RIP: native_queued_spin_lock_slowpath+1291] RIP: ffffffff8127e72b RSP: ffff88aa841ef778 RFLAGS: 00000046 RAX: 0000000000000000 RBX: ffff88b01f849700 RCX: ffffffff8127e47e RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff83857ec0 RBP: ffff88afe3e4efc8 R8: ffffed15fc7c9dfa R9: ffffed15fc7c9dfa R10: 0000000000000001 R11: ffffed15fc7c9df9 R12: 0000000000740000 R13: ffff88b01f849708 R14: 0000000000000003 R15: ffffed1603f092e1 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000 -- <NMI exception stack> -- Freescale#5 [ffff88aa841ef778] native_queued_spin_lock_slowpath at ffffffff8127e72b Freescale#6 [ffff88aa841ef7b0] _raw_spin_lock_irqsave at ffffffff82c22aa4 Freescale#7 [ffff88aa841ef7c8] __wake_up_common_lock at ffffffff81257363 Freescale#8 [ffff88aa841ef888] irdma_free_pending_cqp_request at ffffffffa0ba12cc [irdma] Freescale#9 [ffff88aa841ef958] irdma_cleanup_pending_cqp_op at ffffffffa0ba1469 [irdma] Freescale#10 [ffff88aa841ef9c0] irdma_ctrl_deinit_hw at ffffffffa0b2989f [irdma] Freescale#11 [ffff88aa841efa28] irdma_remove at ffffffffa0b252df [irdma] Freescale#12 [ffff88aa841efae8] auxiliary_bus_remove at ffffffff8219afdb Freescale#13 [ffff88aa841efb00] device_release_driver_internal at ffffffff821882e6 Freescale#14 [ffff88aa841efb38] bus_remove_device at ffffffff82184278 Freescale#15 [ffff88aa841efb88] device_del at ffffffff82179d23 Freescale#16 [ffff88aa841efc48] ice_unplug_aux_dev at ffffffffa0eb1c14 [ice] Freescale#17 [ffff88aa841efc68] ice_service_task at ffffffffa0d88201 [ice] Freescale#18 [ffff88aa841efde8] process_one_work at ffffffff811c589a Freescale#19 [ffff88aa841efe60] worker_thread at ffffffff811c71ff Freescale#20 [ffff88aa841eff10] kthread at ffffffff811d87a0 Freescale#21 [ffff88aa841eff50] ret_from_fork at ffffffff82e0022f Fixes: 44d9e52 ("RDMA/irdma: Implement device initialization definitions") Link: https://lore.kernel.org/r/[email protected] Suggested-by: "Ismail, Mustafa" <[email protected]> Signed-off-by: Shifeng Li <[email protected]> Reviewed-by: Shiraz Saleem <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 00d6a28 ] Commit a5a9230 (fbdev: fbcon: Properly revert changes when vc_resize() failed) started restoring old font data upon failure (of vc_resize()). But it performs so only for user fonts. It means that the "system"/internal fonts are not restored at all. So in result, the very first call to fbcon_do_set_font() performs no restore at all upon failing vc_resize(). This can be reproduced by Syzkaller to crash the system on the next invocation of font_get(). It's rather hard to hit the allocation failure in vc_resize() on the first font_set(), but not impossible. Esp. if fault injection is used to aid the execution/failure. It was demonstrated by Sirius: BUG: unable to handle page fault for address: fffffffffffffff8 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD cb7b067 P4D cb7b067 PUD cb7d067 PMD 0 Oops: 0000 [Freescale#1] PREEMPT SMP KASAN CPU: 1 PID: 8007 Comm: poc Not tainted 6.7.0-g9d1694dc91ce Freescale#20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:fbcon_get_font+0x229/0x800 drivers/video/fbdev/core/fbcon.c:2286 Call Trace: <TASK> con_font_get drivers/tty/vt/vt.c:4558 [inline] con_font_op+0x1fc/0xf20 drivers/tty/vt/vt.c:4673 vt_k_ioctl drivers/tty/vt/vt_ioctl.c:474 [inline] vt_ioctl+0x632/0x2ec0 drivers/tty/vt/vt_ioctl.c:752 tty_ioctl+0x6f8/0x1570 drivers/tty/tty_io.c:2803 vfs_ioctl fs/ioctl.c:51 [inline] ... So restore the font data in any case, not only for user fonts. Note the later 'if' is now protected by 'old_userfont' and not 'old_data' as the latter is always set now. (And it is supposed to be non-NULL. Otherwise we would see the bug above again.) Signed-off-by: Jiri Slaby (SUSE) <[email protected]> Fixes: a5a9230 ("fbdev: fbcon: Properly revert changes when vc_resize() failed") Reported-and-tested-by: Ubisectech Sirius <[email protected]> Cc: Ubisectech Sirius <[email protected]> Cc: Daniel Vetter <[email protected]> Cc: Helge Deller <[email protected]> Cc: [email protected] Cc: [email protected] Signed-off-by: Daniel Vetter <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Signed-off-by: Sasha Levin <[email protected]>

commit a5b862c upstream. l2cap_le_flowctl_init() can cause both div-by-zero and an integer overflow since hdev->le_mtu may not fall in the valid range. Move MTU from hci_dev to hci_conn to validate MTU and stop the connection process earlier if MTU is invalid. Also, add a missing validation in read_buffer_size() and make it return an error value if the validation fails. Now hci_conn_add() returns ERR_PTR() as it can fail due to the both a kzalloc failure and invalid MTU value. divide error: 0000 [#1] PREEMPT SMP KASAN NOPTI CPU: 0 PID: 67 Comm: kworker/u5:0 Tainted: G W 6.9.0-rc5+ #20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Workqueue: hci0 hci_rx_work RIP: 0010:l2cap_le_flowctl_init+0x19e/0x3f0 net/bluetooth/l2cap_core.c:547 Code: e8 17 17 0c 00 66 41 89 9f 84 00 00 00 bf 01 00 00 00 41 b8 02 00 00 00 4c 89 fe 4c 89 e2 89 d9 e8 27 17 0c 00 44 89 f0 31 d2 <66> f7 f3 89 c3 ff c3 4d 8d b7 88 00 00 00 4c 89 f0 48 c1 e8 03 42 RSP: 0018:ffff88810bc0f858 EFLAGS: 00010246 RAX: 00000000000002a0 RBX: 0000000000000000 RCX: dffffc0000000000 RDX: 0000000000000000 RSI: ffff88810bc0f7c0 RDI: ffffc90002dcb66f RBP: ffff88810bc0f880 R08: aa69db2dda70ff01 R09: 0000ffaaaaaaaaaa R10: 0084000000ffaaaa R11: 0000000000000000 R12: ffff88810d65a084 R13: dffffc0000000000 R14: 00000000000002a0 R15: ffff88810d65a000 FS: 0000000000000000(0000) GS:ffff88811ac00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000100 CR3: 0000000103268003 CR4: 0000000000770ef0 PKRU: 55555554 Call Trace: <TASK> l2cap_le_connect_req net/bluetooth/l2cap_core.c:4902 [inline] l2cap_le_sig_cmd net/bluetooth/l2cap_core.c:5420 [inline] l2cap_le_sig_channel net/bluetooth/l2cap_core.c:5486 [inline] l2cap_recv_frame+0xe59d/0x11710 net/bluetooth/l2cap_core.c:6809 l2cap_recv_acldata+0x544/0x10a0 net/bluetooth/l2cap_core.c:7506 hci_acldata_packet net/bluetooth/hci_core.c:3939 [inline] hci_rx_work+0x5e5/0xb20 net/bluetooth/hci_core.c:4176 process_one_work kernel/workqueue.c:3254 [inline] process_scheduled_works+0x90f/0x1530 kernel/workqueue.c:3335 worker_thread+0x926/0xe70 kernel/workqueue.c:3416 kthread+0x2e3/0x380 kernel/kthread.c:388 ret_from_fork+0x5c/0x90 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- Fixes: 6ed58ec ("Bluetooth: Use LE buffers for LE traffic") Suggested-by: Luiz Augusto von Dentz <[email protected]> Signed-off-by: Sungwoo Kim <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 769e6a1 ] ui_browser__show() is capturing the input title that is stack allocated memory in hist_browser__run(). Avoid a use after return by strdup-ing the string. Committer notes: Further explanation from Ian Rogers: My command line using tui is: $ sudo bash -c 'rm /tmp/asan.log*; export ASAN_OPTIONS="log_path=/tmp/asan.log"; /tmp/perf/perf mem record -a sleep 1; /tmp/perf/perf mem report' I then go to the perf annotate view and quit. This triggers the asan error (from the log file): ``` ==1254591==ERROR: AddressSanitizer: stack-use-after-return on address 0x7f2813331920 at pc 0x7f28180 65991 bp 0x7fff0a21c750 sp 0x7fff0a21bf10 READ of size 80 at 0x7f2813331920 thread T0 #0 0x7f2818065990 in __interceptor_strlen ../../../../src/libsanitizer/sanitizer_common/sanitizer_common_interceptors.inc:461 #1 0x7f2817698251 in SLsmg_write_wrapped_string (/lib/x86_64-linux-gnu/libslang.so.2+0x98251) #2 0x7f28176984b9 in SLsmg_write_nstring (/lib/x86_64-linux-gnu/libslang.so.2+0x984b9) #3 0x55c94045b365 in ui_browser__write_nstring ui/browser.c:60 #4 0x55c94045c558 in __ui_browser__show_title ui/browser.c:266 #5 0x55c94045c776 in ui_browser__show ui/browser.c:288 #6 0x55c94045c06d in ui_browser__handle_resize ui/browser.c:206 #7 0x55c94047979b in do_annotate ui/browsers/hists.c:2458 #8 0x55c94047fb17 in evsel__hists_browse ui/browsers/hists.c:3412 #9 0x55c940480a0c in perf_evsel_menu__run ui/browsers/hists.c:3527 #10 0x55c940481108 in __evlist__tui_browse_hists ui/browsers/hists.c:3613 #11 0x55c9404813f7 in evlist__tui_browse_hists ui/browsers/hists.c:3661 #12 0x55c93ffa253f in report__browse_hists tools/perf/builtin-report.c:671 #13 0x55c93ffa58ca in __cmd_report tools/perf/builtin-report.c:1141 #14 0x55c93ffaf159 in cmd_report tools/perf/builtin-report.c:1805 #15 0x55c94000c05c in report_events tools/perf/builtin-mem.c:374 #16 0x55c94000d96d in cmd_mem tools/perf/builtin-mem.c:516 #17 0x55c9400e44ee in run_builtin tools/perf/perf.c:350 #18 0x55c9400e4a5a in handle_internal_command tools/perf/perf.c:403 #19 0x55c9400e4e22 in run_argv tools/perf/perf.c:447 #20 0x55c9400e53ad in main tools/perf/perf.c:561 #21 0x7f28170456c9 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 #22 0x7f2817045784 in __libc_start_main_impl ../csu/libc-start.c:360 #23 0x55c93ff544c0 in _start (/tmp/perf/perf+0x19a4c0) (BuildId: 84899b0e8c7d3a3eaa67b2eb35e3d8b2f8cd4c93) Address 0x7f2813331920 is located in stack of thread T0 at offset 32 in frame #0 0x55c94046e85e in hist_browser__run ui/browsers/hists.c:746 This frame has 1 object(s): [32, 192) 'title' (line 747) <== Memory access at offset 32 is inside this variable HINT: this may be a false positive if your program uses some custom stack unwind mechanism, swapcontext or vfork ``` hist_browser__run isn't on the stack so the asan error looks legit. There's no clean init/exit on struct ui_browser so I may be trading a use-after-return for a memory leak, but that seems look a good trade anyway. Fixes: 05e8b08 ("perf ui browser: Stop using 'self'") Signed-off-by: Ian Rogers <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Athira Rajeev <[email protected]> Cc: Ben Gainey <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: James Clark <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kajol Jain <[email protected]> Cc: Kan Liang <[email protected]> Cc: K Prateek Nayak <[email protected]> Cc: Li Dong <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Oliver Upton <[email protected]> Cc: Paran Lee <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Ravi Bangoria <[email protected]> Cc: Sun Haiyong <[email protected]> Cc: Tim Chen <[email protected]> Cc: Yanteng Si <[email protected]> Cc: Yicong Yang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 Freescale#1 __crash_kexec at ffffffff8c1338fa Freescale#2 panic at ffffffff8c1d69b9 Freescale#3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] Freescale#4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] Freescale#5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] Freescale#6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] Freescale#7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] Freescale#8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] Freescale#9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] Freescale#10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] Freescale#11 dio_complete at ffffffff8c2b9fa7 Freescale#12 do_blockdev_direct_IO at ffffffff8c2bc09f Freescale#13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] Freescale#14 generic_file_direct_write at ffffffff8c1dcf14 Freescale#15 __generic_file_write_iter at ffffffff8c1dd07b Freescale#16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] Freescale#17 aio_write at ffffffff8c2cc72e Freescale#18 kmem_cache_alloc at ffffffff8c248dde Freescale#19 do_io_submit at ffffffff8c2ccada Freescale#20 do_syscall_64 at ffffffff8c004984 Freescale#21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit bab4923 upstream. In the TRACE_EVENT(qdisc_reset) NULL dereference occurred from qdisc->dev_queue->dev <NULL> ->name This situation simulated from bunch of veths and Bluetooth disconnection and reconnection. During qdisc initialization, qdisc was being set to noop_queue. In veth_init_queue, the initial tx_num was reduced back to one, causing the qdisc reset to be called with noop, which led to the kernel panic. I've attached the GitHub gist link that C converted syz-execprogram source code and 3 log of reproduced vmcore-dmesg. https://gist.github.com/yskelg/cc64562873ce249cdd0d5a358b77d740 Yeoreum and I use two fuzzing tool simultaneously. One process with syz-executor : https://github.com/google/syzkaller $ ./syz-execprog -executor=./syz-executor -repeat=1 -sandbox=setuid \ -enable=none -collide=false log1 The other process with perf fuzzer: https://github.com/deater/perf_event_tests/tree/master/fuzzer $ perf_event_tests/fuzzer/perf_fuzzer I think this will happen on the kernel version. Linux kernel version +v6.7.10, +v6.8, +v6.9 and it could happen in v6.10. This occurred from 51270d5. I think this patch is absolutely necessary. Previously, It was showing not intended string value of name. I've reproduced 3 time from my fedora 40 Debug Kernel with any other module or patched. version: 6.10.0-0.rc2.20240608gitdc772f8237f9.29.fc41.aarch64+debug [ 5287.164555] veth0_vlan: left promiscuous mode [ 5287.164929] veth1_macvtap: left promiscuous mode [ 5287.164950] veth0_macvtap: left promiscuous mode [ 5287.164983] veth1_vlan: left promiscuous mode [ 5287.165008] veth0_vlan: left promiscuous mode [ 5287.165450] veth1_macvtap: left promiscuous mode [ 5287.165472] veth0_macvtap: left promiscuous mode [ 5287.165502] veth1_vlan: left promiscuous mode … [ 5297.598240] bridge0: port 2(bridge_slave_1) entered blocking state [ 5297.598262] bridge0: port 2(bridge_slave_1) entered forwarding state [ 5297.598296] bridge0: port 1(bridge_slave_0) entered blocking state [ 5297.598313] bridge0: port 1(bridge_slave_0) entered forwarding state [ 5297.616090] 8021q: adding VLAN 0 to HW filter on device bond0 [ 5297.620405] bridge0: port 1(bridge_slave_0) entered disabled state [ 5297.620730] bridge0: port 2(bridge_slave_1) entered disabled state [ 5297.627247] 8021q: adding VLAN 0 to HW filter on device team0 [ 5297.629636] bridge0: port 1(bridge_slave_0) entered blocking state … [ 5298.002798] bridge_slave_0: left promiscuous mode [ 5298.002869] bridge0: port 1(bridge_slave_0) entered disabled state [ 5298.309444] bond0 (unregistering): (slave bond_slave_0): Releasing backup interface [ 5298.315206] bond0 (unregistering): (slave bond_slave_1): Releasing backup interface [ 5298.320207] bond0 (unregistering): Released all slaves [ 5298.354296] hsr_slave_0: left promiscuous mode [ 5298.360750] hsr_slave_1: left promiscuous mode [ 5298.374889] veth1_macvtap: left promiscuous mode [ 5298.374931] veth0_macvtap: left promiscuous mode [ 5298.374988] veth1_vlan: left promiscuous mode [ 5298.375024] veth0_vlan: left promiscuous mode [ 5299.109741] team0 (unregistering): Port device team_slave_1 removed [ 5299.185870] team0 (unregistering): Port device team_slave_0 removed … [ 5300.155443] Bluetooth: hci3: unexpected cc 0x0c03 length: 249 > 1 [ 5300.155724] Bluetooth: hci3: unexpected cc 0x1003 length: 249 > 9 [ 5300.155988] Bluetooth: hci3: unexpected cc 0x1001 length: 249 > 9 …. [ 5301.075531] team0: Port device team_slave_1 added [ 5301.085515] bridge0: port 1(bridge_slave_0) entered blocking state [ 5301.085531] bridge0: port 1(bridge_slave_0) entered disabled state [ 5301.085588] bridge_slave_0: entered allmulticast mode [ 5301.085800] bridge_slave_0: entered promiscuous mode [ 5301.095617] bridge0: port 1(bridge_slave_0) entered blocking state [ 5301.095633] bridge0: port 1(bridge_slave_0) entered disabled state … [ 5301.149734] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.173234] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.180517] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link [ 5301.193481] hsr_slave_0: entered promiscuous mode [ 5301.204425] hsr_slave_1: entered promiscuous mode [ 5301.210172] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.210185] Cannot create hsr debugfs directory [ 5301.224061] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link [ 5301.246901] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.255934] team0: Port device team_slave_0 added [ 5301.256480] team0: Port device team_slave_1 added [ 5301.256948] team0: Port device team_slave_0 added … [ 5301.435928] hsr_slave_0: entered promiscuous mode [ 5301.446029] hsr_slave_1: entered promiscuous mode [ 5301.455872] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.455884] Cannot create hsr debugfs directory [ 5301.502664] hsr_slave_0: entered promiscuous mode [ 5301.513675] hsr_slave_1: entered promiscuous mode [ 5301.526155] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.526164] Cannot create hsr debugfs directory [ 5301.563662] hsr_slave_0: entered promiscuous mode [ 5301.576129] hsr_slave_1: entered promiscuous mode [ 5301.580259] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.580270] Cannot create hsr debugfs directory [ 5301.590269] 8021q: adding VLAN 0 to HW filter on device bond0 [ 5301.595872] KASAN: null-ptr-deref in range [0x0000000000000130-0x0000000000000137] [ 5301.595877] Mem abort info: [ 5301.595881] ESR = 0x0000000096000006 [ 5301.595885] EC = 0x25: DABT (current EL), IL = 32 bits [ 5301.595889] SET = 0, FnV = 0 [ 5301.595893] EA = 0, S1PTW = 0 [ 5301.595896] FSC = 0x06: level 2 translation fault [ 5301.595900] Data abort info: [ 5301.595903] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000 [ 5301.595907] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 5301.595911] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 5301.595915] [dfff800000000026] address between user and kernel address ranges [ 5301.595971] Internal error: Oops: 0000000096000006 [Freescale#1] SMP … [ 5301.596076] CPU: 2 PID: 102769 Comm: syz-executor.3 Kdump: loaded Tainted: G W ------- --- 6.10.0-0.rc2.20240608gitdc772f8237f9.29.fc41.aarch64+debug Freescale#1 [ 5301.596080] Hardware name: VMware, Inc. VMware20,1/VBSA, BIOS VMW201.00V.21805430.BA64.2305221830 05/22/2023 [ 5301.596082] pstate: 01400005 (nzcv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 5301.596085] pc : strnlen+0x40/0x88 [ 5301.596114] lr : trace_event_get_offsets_qdisc_reset+0x6c/0x2b0 [ 5301.596124] sp : ffff8000beef6b40 [ 5301.596126] x29: ffff8000beef6b40 x28: dfff800000000000 x27: 0000000000000001 [ 5301.596131] x26: 6de1800082c62bd0 x25: 1ffff000110aa9e0 x24: ffff800088554f00 [ 5301.596136] x23: ffff800088554ec0 x22: 0000000000000130 x21: 0000000000000140 [ 5301.596140] x20: dfff800000000000 x19: ffff8000beef6c60 x18: ffff7000115106d8 [ 5301.596143] x17: ffff800121bad000 x16: ffff800080020000 x15: 0000000000000006 [ 5301.596147] x14: 0000000000000002 x13: ffff0001f3ed8d14 x12: ffff700017ddeda5 [ 5301.596151] x11: 1ffff00017ddeda4 x10: ffff700017ddeda4 x9 : ffff800082cc5eec [ 5301.596155] x8 : 0000000000000004 x7 : 00000000f1f1f1f1 x6 : 00000000f2f2f200 [ 5301.596158] x5 : 00000000f3f3f3f3 x4 : ffff700017dded80 x3 : 00000000f204f1f1 [ 5301.596162] x2 : 0000000000000026 x1 : 0000000000000000 x0 : 0000000000000130 [ 5301.596166] Call trace: [ 5301.596175] strnlen+0x40/0x88 [ 5301.596179] trace_event_get_offsets_qdisc_reset+0x6c/0x2b0 [ 5301.596182] perf_trace_qdisc_reset+0xb0/0x538 [ 5301.596184] __traceiter_qdisc_reset+0x68/0xc0 [ 5301.596188] qdisc_reset+0x43c/0x5e8 [ 5301.596190] netif_set_real_num_tx_queues+0x288/0x770 [ 5301.596194] veth_init_queues+0xfc/0x130 [veth] [ 5301.596198] veth_newlink+0x45c/0x850 [veth] [ 5301.596202] rtnl_newlink_create+0x2c8/0x798 [ 5301.596205] __rtnl_newlink+0x92c/0xb60 [ 5301.596208] rtnl_newlink+0xd8/0x130 [ 5301.596211] rtnetlink_rcv_msg+0x2e0/0x890 [ 5301.596214] netlink_rcv_skb+0x1c4/0x380 [ 5301.596225] rtnetlink_rcv+0x20/0x38 [ 5301.596227] netlink_unicast+0x3c8/0x640 [ 5301.596231] netlink_sendmsg+0x658/0xa60 [ 5301.596234] __sock_sendmsg+0xd0/0x180 [ 5301.596243] __sys_sendto+0x1c0/0x280 [ 5301.596246] __arm64_sys_sendto+0xc8/0x150 [ 5301.596249] invoke_syscall+0xdc/0x268 [ 5301.596256] el0_svc_common.constprop.0+0x16c/0x240 [ 5301.596259] do_el0_svc+0x48/0x68 [ 5301.596261] el0_svc+0x50/0x188 [ 5301.596265] el0t_64_sync_handler+0x120/0x130 [ 5301.596268] el0t_64_sync+0x194/0x198 [ 5301.596272] Code: eb15001f 54000120 d343fc02 12000801 (38f46842) [ 5301.596285] SMP: stopping secondary CPUs [ 5301.597053] Starting crashdump kernel... [ 5301.597057] Bye! After applying our patch, I didn't find any kernel panic errors. We've found a simple reproducer # echo 1 > /sys/kernel/debug/tracing/events/qdisc/qdisc_reset/enable # ip link add veth0 type veth peer name veth1 Error: Unknown device type. However, without our patch applied, I tested upstream 6.10.0-rc3 kernel using the qdisc_reset event and the ip command on my qemu virtual machine. This 2 commands makes always kernel panic. Linux version: 6.10.0-rc3 [ 0.000000] Linux version 6.10.0-rc3-00164-g44ef20baed8e-dirty (paran@fedora) (gcc (GCC) 14.1.1 20240522 (Red Hat 14.1.1-4), GNU ld version 2.41-34.fc40) Freescale#20 SMP PREEMPT Sat Jun 15 16:51:25 KST 2024 Kernel panic message: [ 615.236484] Internal error: Oops: 0000000096000005 [Freescale#1] PREEMPT SMP [ 615.237250] Dumping ftrace buffer: [ 615.237679] (ftrace buffer empty) [ 615.238097] Modules linked in: veth crct10dif_ce virtio_gpu virtio_dma_buf drm_shmem_helper drm_kms_helper zynqmp_fpga xilinx_can xilinx_spi xilinx_selectmap xilinx_core xilinx_pr_decoupler versal_fpga uvcvideo uvc videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videodev videobuf2_common mc usbnet deflate zstd ubifs ubi rcar_canfd rcar_can omap_mailbox ntb_msi_test ntb_hw_epf lattice_sysconfig_spi lattice_sysconfig ice40_spi gpio_xilinx dwmac_altr_socfpga mdio_regmap stmmac_platform stmmac pcs_xpcs dfl_fme_region dfl_fme_mgr dfl_fme_br dfl_afu dfl fpga_region fpga_bridge can can_dev br_netfilter bridge stp llc atl1c ath11k_pci mhi ath11k_ahb ath11k qmi_helpers ath10k_sdio ath10k_pci ath10k_core ath mac80211 libarc4 cfg80211 drm fuse backlight ipv6 Jun 22 02:36:5[3 6k152.62-4sm98k4-0k]v kCePUr:n e1l :P IUDn:a b4le6 8t oC ohmma: nidpl eN oketr nteali nptaedg i6n.g1 0re.0q-urecs3t- 0at0 1v6i4r-tgu4a4le fa2d0dbraeeds0se-dir tyd f#f2f08 615.252376] Hardware name: linux,dummy-virt (DT) [ 615.253220] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 615.254433] pc : strnlen+0x6c/0xe0 [ 615.255096] lr : trace_event_get_offsets_qdisc_reset+0x94/0x3d0 [ 615.256088] sp : ffff800080b269a0 [ 615.256615] x29: ffff800080b269a0 x28: ffffc070f3f98500 x27: 0000000000000001 [ 615.257831] x26: 0000000000000010 x25: ffffc070f3f98540 x24: ffffc070f619cf60 [ 615.259020] x23: 0000000000000128 x22: 0000000000000138 x21: dfff800000000000 [ 615.260241] x20: ffffc070f631ad00 x19: 0000000000000128 x18: ffffc070f448b800 [ 615.261454] x17: 0000000000000000 x16: 0000000000000001 x15: ffffc070f4ba2a90 [ 615.262635] x14: ffff700010164d73 x13: 1ffff80e1e8d5eb3 x12: 1ffff00010164d72 [ 615.263877] x11: ffff700010164d72 x10: dfff800000000000 x9 : ffffc070e85d6184 [ 615.265047] x8 : ffffc070e4402070 x7 : 000000000000f1f1 x6 : 000000001504a6d3 [ 615.266336] x5 : ffff28ca21122140 x4 : ffffc070f5043ea8 x3 : 0000000000000000 [ 615.267528] x2 : 0000000000000025 x1 : 0000000000000000 x0 : 0000000000000000 [ 615.268747] Call trace: [ 615.269180] strnlen+0x6c/0xe0 [ 615.269767] trace_event_get_offsets_qdisc_reset+0x94/0x3d0 [ 615.270716] trace_event_raw_event_qdisc_reset+0xe8/0x4e8 [ 615.271667] __traceiter_qdisc_reset+0xa0/0x140 [ 615.272499] qdisc_reset+0x554/0x848 [ 615.273134] netif_set_real_num_tx_queues+0x360/0x9a8 [ 615.274050] veth_init_queues+0x110/0x220 [veth] [ 615.275110] veth_newlink+0x538/0xa50 [veth] [ 615.276172] __rtnl_newlink+0x11e4/0x1bc8 [ 615.276944] rtnl_newlink+0xac/0x120 [ 615.277657] rtnetlink_rcv_msg+0x4e4/0x1370 [ 615.278409] netlink_rcv_skb+0x25c/0x4f0 [ 615.279122] rtnetlink_rcv+0x48/0x70 [ 615.279769] netlink_unicast+0x5a8/0x7b8 [ 615.280462] netlink_sendmsg+0xa70/0x1190 Yeoreum and I don't know if the patch we wrote will fix the underlying cause, but we think that priority is to prevent kernel panic happening. So, we're sending this patch. Fixes: 51270d5 ("tracing/net_sched: Fix tracepoints that save qdisc_dev() as a string") Link: https://lore.kernel.org/lkml/[email protected]/t/ Cc: [email protected] Tested-by: Yunseong Kim <[email protected]> Signed-off-by: Yunseong Kim <[email protected]> Signed-off-by: Yeoreum Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit db19d3a ] There is a race condition in the CMT interrupt handler. In the interrupt handler the driver sets a driver private flag, FLAG_IRQCONTEXT. This flag is used to indicate any call to set_next_event() should not be directly propagated to the device, but instead cached. This is done as the interrupt handler itself reprograms the device when needed before it completes and this avoids this operation to take place twice. It is unclear why this design was chosen, my suspicion is to allow the struct clock_event_device.event_handler callback, which is called while the FLAG_IRQCONTEXT is set, can update the next event without having to write to the device twice. Unfortunately there is a race between when the FLAG_IRQCONTEXT flag is set and later cleared where the interrupt handler have already started to write the next event to the device. If set_next_event() is called in this window the value is only cached in the driver but not written. This leads to the board to misbehave, or worse lockup and produce a splat. rcu: INFO: rcu_preempt detected stalls on CPUs/tasks: rcu: 0-...!: (0 ticks this GP) idle=f5e0/0/0x0 softirq=519/519 fqs=0 (false positive?) rcu: (detected by 1, t=6502 jiffies, g=-595, q=77 ncpus=2) Sending NMI from CPU 1 to CPUs 0: NMI backtrace for cpu 0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.10.0-rc5-arm64-renesas-00019-g74a6f86eaf1c-dirty Freescale#20 Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tick_check_broadcast_expired+0xc/0x40 lr : cpu_idle_poll.isra.0+0x8c/0x168 sp : ffff800081c63d70 x29: ffff800081c63d70 x28: 00000000580000c8 x27: 00000000bfee5610 x26: 0000000000000027 x25: 0000000000000000 x24: 0000000000000000 x23: ffff00007fbb9100 x22: ffff8000818f1008 x21: ffff8000800ef07c x20: ffff800081c79ec0 x19: ffff800081c70c28 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffc2c717d8 x14: 0000000000000000 x13: ffff000009c18080 x12: ffff8000825f7fc0 x11: 0000000000000000 x10: ffff8000818f3cd4 x9 : 0000000000000028 x8 : ffff800081c79ec0 x7 : ffff800081c73000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : ffff7ffffe286000 x3 : 0000000000000000 x2 : ffff7ffffe286000 x1 : ffff800082972900 x0 : ffff8000818f1008 Call trace: tick_check_broadcast_expired+0xc/0x40 do_idle+0x9c/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x11c do_one_initcall+0x0/0x260 __primary_switched+0x80/0x88 rcu: rcu_preempt kthread timer wakeup didn't happen for 6501 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 rcu: Possible timer handling issue on cpu=0 timer-softirq=262 rcu: rcu_preempt kthread starved for 6502 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0 rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior. rcu: RCU grace-period kthread stack dump: task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 flags:0x00000008 Call trace: __switch_to+0xbc/0x100 __schedule+0x358/0xbe0 schedule+0x48/0x148 schedule_timeout+0xc4/0x138 rcu_gp_fqs_loop+0x12c/0x764 rcu_gp_kthread+0x208/0x298 kthread+0x10c/0x110 ret_from_fork+0x10/0x20 The design have been part of the driver since it was first merged in early 2009. It becomes increasingly harder to trigger the issue the older kernel version one tries. It only takes a few boots on v6.10-rc5, while hundreds of boots are needed to trigger it on v5.10. Close the race condition by using the CMT channel lock for the two competing sections. The channel lock was added to the driver after its initial design. Signed-off-by: Niklas Söderlund <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Daniel Lezcano <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 Freescale#1 __crash_kexec at ffffffff8c1338fa Freescale#2 panic at ffffffff8c1d69b9 Freescale#3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] Freescale#4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] Freescale#5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] Freescale#6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] Freescale#7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] Freescale#8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] Freescale#9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] Freescale#10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] Freescale#11 dio_complete at ffffffff8c2b9fa7 Freescale#12 do_blockdev_direct_IO at ffffffff8c2bc09f Freescale#13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] Freescale#14 generic_file_direct_write at ffffffff8c1dcf14 Freescale#15 __generic_file_write_iter at ffffffff8c1dd07b Freescale#16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] Freescale#17 aio_write at ffffffff8c2cc72e Freescale#18 kmem_cache_alloc at ffffffff8c248dde Freescale#19 do_io_submit at ffffffff8c2ccada Freescale#20 do_syscall_64 at ffffffff8c004984 Freescale#21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit bab4923 upstream. In the TRACE_EVENT(qdisc_reset) NULL dereference occurred from qdisc->dev_queue->dev <NULL> ->name This situation simulated from bunch of veths and Bluetooth disconnection and reconnection. During qdisc initialization, qdisc was being set to noop_queue. In veth_init_queue, the initial tx_num was reduced back to one, causing the qdisc reset to be called with noop, which led to the kernel panic. I've attached the GitHub gist link that C converted syz-execprogram source code and 3 log of reproduced vmcore-dmesg. https://gist.github.com/yskelg/cc64562873ce249cdd0d5a358b77d740 Yeoreum and I use two fuzzing tool simultaneously. One process with syz-executor : https://github.com/google/syzkaller $ ./syz-execprog -executor=./syz-executor -repeat=1 -sandbox=setuid \ -enable=none -collide=false log1 The other process with perf fuzzer: https://github.com/deater/perf_event_tests/tree/master/fuzzer $ perf_event_tests/fuzzer/perf_fuzzer I think this will happen on the kernel version. Linux kernel version +v6.7.10, +v6.8, +v6.9 and it could happen in v6.10. This occurred from 51270d5. I think this patch is absolutely necessary. Previously, It was showing not intended string value of name. I've reproduced 3 time from my fedora 40 Debug Kernel with any other module or patched. version: 6.10.0-0.rc2.20240608gitdc772f8237f9.29.fc41.aarch64+debug [ 5287.164555] veth0_vlan: left promiscuous mode [ 5287.164929] veth1_macvtap: left promiscuous mode [ 5287.164950] veth0_macvtap: left promiscuous mode [ 5287.164983] veth1_vlan: left promiscuous mode [ 5287.165008] veth0_vlan: left promiscuous mode [ 5287.165450] veth1_macvtap: left promiscuous mode [ 5287.165472] veth0_macvtap: left promiscuous mode [ 5287.165502] veth1_vlan: left promiscuous mode … [ 5297.598240] bridge0: port 2(bridge_slave_1) entered blocking state [ 5297.598262] bridge0: port 2(bridge_slave_1) entered forwarding state [ 5297.598296] bridge0: port 1(bridge_slave_0) entered blocking state [ 5297.598313] bridge0: port 1(bridge_slave_0) entered forwarding state [ 5297.616090] 8021q: adding VLAN 0 to HW filter on device bond0 [ 5297.620405] bridge0: port 1(bridge_slave_0) entered disabled state [ 5297.620730] bridge0: port 2(bridge_slave_1) entered disabled state [ 5297.627247] 8021q: adding VLAN 0 to HW filter on device team0 [ 5297.629636] bridge0: port 1(bridge_slave_0) entered blocking state … [ 5298.002798] bridge_slave_0: left promiscuous mode [ 5298.002869] bridge0: port 1(bridge_slave_0) entered disabled state [ 5298.309444] bond0 (unregistering): (slave bond_slave_0): Releasing backup interface [ 5298.315206] bond0 (unregistering): (slave bond_slave_1): Releasing backup interface [ 5298.320207] bond0 (unregistering): Released all slaves [ 5298.354296] hsr_slave_0: left promiscuous mode [ 5298.360750] hsr_slave_1: left promiscuous mode [ 5298.374889] veth1_macvtap: left promiscuous mode [ 5298.374931] veth0_macvtap: left promiscuous mode [ 5298.374988] veth1_vlan: left promiscuous mode [ 5298.375024] veth0_vlan: left promiscuous mode [ 5299.109741] team0 (unregistering): Port device team_slave_1 removed [ 5299.185870] team0 (unregistering): Port device team_slave_0 removed … [ 5300.155443] Bluetooth: hci3: unexpected cc 0x0c03 length: 249 > 1 [ 5300.155724] Bluetooth: hci3: unexpected cc 0x1003 length: 249 > 9 [ 5300.155988] Bluetooth: hci3: unexpected cc 0x1001 length: 249 > 9 …. [ 5301.075531] team0: Port device team_slave_1 added [ 5301.085515] bridge0: port 1(bridge_slave_0) entered blocking state [ 5301.085531] bridge0: port 1(bridge_slave_0) entered disabled state [ 5301.085588] bridge_slave_0: entered allmulticast mode [ 5301.085800] bridge_slave_0: entered promiscuous mode [ 5301.095617] bridge0: port 1(bridge_slave_0) entered blocking state [ 5301.095633] bridge0: port 1(bridge_slave_0) entered disabled state … [ 5301.149734] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.173234] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.180517] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link [ 5301.193481] hsr_slave_0: entered promiscuous mode [ 5301.204425] hsr_slave_1: entered promiscuous mode [ 5301.210172] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.210185] Cannot create hsr debugfs directory [ 5301.224061] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link [ 5301.246901] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.255934] team0: Port device team_slave_0 added [ 5301.256480] team0: Port device team_slave_1 added [ 5301.256948] team0: Port device team_slave_0 added … [ 5301.435928] hsr_slave_0: entered promiscuous mode [ 5301.446029] hsr_slave_1: entered promiscuous mode [ 5301.455872] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.455884] Cannot create hsr debugfs directory [ 5301.502664] hsr_slave_0: entered promiscuous mode [ 5301.513675] hsr_slave_1: entered promiscuous mode [ 5301.526155] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.526164] Cannot create hsr debugfs directory [ 5301.563662] hsr_slave_0: entered promiscuous mode [ 5301.576129] hsr_slave_1: entered promiscuous mode [ 5301.580259] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.580270] Cannot create hsr debugfs directory [ 5301.590269] 8021q: adding VLAN 0 to HW filter on device bond0 [ 5301.595872] KASAN: null-ptr-deref in range [0x0000000000000130-0x0000000000000137] [ 5301.595877] Mem abort info: [ 5301.595881] ESR = 0x0000000096000006 [ 5301.595885] EC = 0x25: DABT (current EL), IL = 32 bits [ 5301.595889] SET = 0, FnV = 0 [ 5301.595893] EA = 0, S1PTW = 0 [ 5301.595896] FSC = 0x06: level 2 translation fault [ 5301.595900] Data abort info: [ 5301.595903] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000 [ 5301.595907] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 5301.595911] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 5301.595915] [dfff800000000026] address between user and kernel address ranges [ 5301.595971] Internal error: Oops: 0000000096000006 [Freescale#1] SMP … [ 5301.596076] CPU: 2 PID: 102769 Comm: syz-executor.3 Kdump: loaded Tainted: G W ------- --- 6.10.0-0.rc2.20240608gitdc772f8237f9.29.fc41.aarch64+debug Freescale#1 [ 5301.596080] Hardware name: VMware, Inc. VMware20,1/VBSA, BIOS VMW201.00V.21805430.BA64.2305221830 05/22/2023 [ 5301.596082] pstate: 01400005 (nzcv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 5301.596085] pc : strnlen+0x40/0x88 [ 5301.596114] lr : trace_event_get_offsets_qdisc_reset+0x6c/0x2b0 [ 5301.596124] sp : ffff8000beef6b40 [ 5301.596126] x29: ffff8000beef6b40 x28: dfff800000000000 x27: 0000000000000001 [ 5301.596131] x26: 6de1800082c62bd0 x25: 1ffff000110aa9e0 x24: ffff800088554f00 [ 5301.596136] x23: ffff800088554ec0 x22: 0000000000000130 x21: 0000000000000140 [ 5301.596140] x20: dfff800000000000 x19: ffff8000beef6c60 x18: ffff7000115106d8 [ 5301.596143] x17: ffff800121bad000 x16: ffff800080020000 x15: 0000000000000006 [ 5301.596147] x14: 0000000000000002 x13: ffff0001f3ed8d14 x12: ffff700017ddeda5 [ 5301.596151] x11: 1ffff00017ddeda4 x10: ffff700017ddeda4 x9 : ffff800082cc5eec [ 5301.596155] x8 : 0000000000000004 x7 : 00000000f1f1f1f1 x6 : 00000000f2f2f200 [ 5301.596158] x5 : 00000000f3f3f3f3 x4 : ffff700017dded80 x3 : 00000000f204f1f1 [ 5301.596162] x2 : 0000000000000026 x1 : 0000000000000000 x0 : 0000000000000130 [ 5301.596166] Call trace: [ 5301.596175] strnlen+0x40/0x88 [ 5301.596179] trace_event_get_offsets_qdisc_reset+0x6c/0x2b0 [ 5301.596182] perf_trace_qdisc_reset+0xb0/0x538 [ 5301.596184] __traceiter_qdisc_reset+0x68/0xc0 [ 5301.596188] qdisc_reset+0x43c/0x5e8 [ 5301.596190] netif_set_real_num_tx_queues+0x288/0x770 [ 5301.596194] veth_init_queues+0xfc/0x130 [veth] [ 5301.596198] veth_newlink+0x45c/0x850 [veth] [ 5301.596202] rtnl_newlink_create+0x2c8/0x798 [ 5301.596205] __rtnl_newlink+0x92c/0xb60 [ 5301.596208] rtnl_newlink+0xd8/0x130 [ 5301.596211] rtnetlink_rcv_msg+0x2e0/0x890 [ 5301.596214] netlink_rcv_skb+0x1c4/0x380 [ 5301.596225] rtnetlink_rcv+0x20/0x38 [ 5301.596227] netlink_unicast+0x3c8/0x640 [ 5301.596231] netlink_sendmsg+0x658/0xa60 [ 5301.596234] __sock_sendmsg+0xd0/0x180 [ 5301.596243] __sys_sendto+0x1c0/0x280 [ 5301.596246] __arm64_sys_sendto+0xc8/0x150 [ 5301.596249] invoke_syscall+0xdc/0x268 [ 5301.596256] el0_svc_common.constprop.0+0x16c/0x240 [ 5301.596259] do_el0_svc+0x48/0x68 [ 5301.596261] el0_svc+0x50/0x188 [ 5301.596265] el0t_64_sync_handler+0x120/0x130 [ 5301.596268] el0t_64_sync+0x194/0x198 [ 5301.596272] Code: eb15001f 54000120 d343fc02 12000801 (38f46842) [ 5301.596285] SMP: stopping secondary CPUs [ 5301.597053] Starting crashdump kernel... [ 5301.597057] Bye! After applying our patch, I didn't find any kernel panic errors. We've found a simple reproducer # echo 1 > /sys/kernel/debug/tracing/events/qdisc/qdisc_reset/enable # ip link add veth0 type veth peer name veth1 Error: Unknown device type. However, without our patch applied, I tested upstream 6.10.0-rc3 kernel using the qdisc_reset event and the ip command on my qemu virtual machine. This 2 commands makes always kernel panic. Linux version: 6.10.0-rc3 [ 0.000000] Linux version 6.10.0-rc3-00164-g44ef20baed8e-dirty (paran@fedora) (gcc (GCC) 14.1.1 20240522 (Red Hat 14.1.1-4), GNU ld version 2.41-34.fc40) Freescale#20 SMP PREEMPT Sat Jun 15 16:51:25 KST 2024 Kernel panic message: [ 615.236484] Internal error: Oops: 0000000096000005 [Freescale#1] PREEMPT SMP [ 615.237250] Dumping ftrace buffer: [ 615.237679] (ftrace buffer empty) [ 615.238097] Modules linked in: veth crct10dif_ce virtio_gpu virtio_dma_buf drm_shmem_helper drm_kms_helper zynqmp_fpga xilinx_can xilinx_spi xilinx_selectmap xilinx_core xilinx_pr_decoupler versal_fpga uvcvideo uvc videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videodev videobuf2_common mc usbnet deflate zstd ubifs ubi rcar_canfd rcar_can omap_mailbox ntb_msi_test ntb_hw_epf lattice_sysconfig_spi lattice_sysconfig ice40_spi gpio_xilinx dwmac_altr_socfpga mdio_regmap stmmac_platform stmmac pcs_xpcs dfl_fme_region dfl_fme_mgr dfl_fme_br dfl_afu dfl fpga_region fpga_bridge can can_dev br_netfilter bridge stp llc atl1c ath11k_pci mhi ath11k_ahb ath11k qmi_helpers ath10k_sdio ath10k_pci ath10k_core ath mac80211 libarc4 cfg80211 drm fuse backlight ipv6 Jun 22 02:36:5[3 6k152.62-4sm98k4-0k]v kCePUr:n e1l :P IUDn:a b4le6 8t oC ohmma: nidpl eN oketr nteali nptaedg i6n.g1 0re.0q-urecs3t- 0at0 1v6i4r-tgu4a4le fa2d0dbraeeds0se-dir tyd f#f2f08 615.252376] Hardware name: linux,dummy-virt (DT) [ 615.253220] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 615.254433] pc : strnlen+0x6c/0xe0 [ 615.255096] lr : trace_event_get_offsets_qdisc_reset+0x94/0x3d0 [ 615.256088] sp : ffff800080b269a0 [ 615.256615] x29: ffff800080b269a0 x28: ffffc070f3f98500 x27: 0000000000000001 [ 615.257831] x26: 0000000000000010 x25: ffffc070f3f98540 x24: ffffc070f619cf60 [ 615.259020] x23: 0000000000000128 x22: 0000000000000138 x21: dfff800000000000 [ 615.260241] x20: ffffc070f631ad00 x19: 0000000000000128 x18: ffffc070f448b800 [ 615.261454] x17: 0000000000000000 x16: 0000000000000001 x15: ffffc070f4ba2a90 [ 615.262635] x14: ffff700010164d73 x13: 1ffff80e1e8d5eb3 x12: 1ffff00010164d72 [ 615.263877] x11: ffff700010164d72 x10: dfff800000000000 x9 : ffffc070e85d6184 [ 615.265047] x8 : ffffc070e4402070 x7 : 000000000000f1f1 x6 : 000000001504a6d3 [ 615.266336] x5 : ffff28ca21122140 x4 : ffffc070f5043ea8 x3 : 0000000000000000 [ 615.267528] x2 : 0000000000000025 x1 : 0000000000000000 x0 : 0000000000000000 [ 615.268747] Call trace: [ 615.269180] strnlen+0x6c/0xe0 [ 615.269767] trace_event_get_offsets_qdisc_reset+0x94/0x3d0 [ 615.270716] trace_event_raw_event_qdisc_reset+0xe8/0x4e8 [ 615.271667] __traceiter_qdisc_reset+0xa0/0x140 [ 615.272499] qdisc_reset+0x554/0x848 [ 615.273134] netif_set_real_num_tx_queues+0x360/0x9a8 [ 615.274050] veth_init_queues+0x110/0x220 [veth] [ 615.275110] veth_newlink+0x538/0xa50 [veth] [ 615.276172] __rtnl_newlink+0x11e4/0x1bc8 [ 615.276944] rtnl_newlink+0xac/0x120 [ 615.277657] rtnetlink_rcv_msg+0x4e4/0x1370 [ 615.278409] netlink_rcv_skb+0x25c/0x4f0 [ 615.279122] rtnetlink_rcv+0x48/0x70 [ 615.279769] netlink_unicast+0x5a8/0x7b8 [ 615.280462] netlink_sendmsg+0xa70/0x1190 Yeoreum and I don't know if the patch we wrote will fix the underlying cause, but we think that priority is to prevent kernel panic happening. So, we're sending this patch. Fixes: 51270d5 ("tracing/net_sched: Fix tracepoints that save qdisc_dev() as a string") Link: https://lore.kernel.org/lkml/[email protected]/t/ Cc: [email protected] Tested-by: Yunseong Kim <[email protected]> Signed-off-by: Yunseong Kim <[email protected]> Signed-off-by: Yeoreum Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit db19d3a ] There is a race condition in the CMT interrupt handler. In the interrupt handler the driver sets a driver private flag, FLAG_IRQCONTEXT. This flag is used to indicate any call to set_next_event() should not be directly propagated to the device, but instead cached. This is done as the interrupt handler itself reprograms the device when needed before it completes and this avoids this operation to take place twice. It is unclear why this design was chosen, my suspicion is to allow the struct clock_event_device.event_handler callback, which is called while the FLAG_IRQCONTEXT is set, can update the next event without having to write to the device twice. Unfortunately there is a race between when the FLAG_IRQCONTEXT flag is set and later cleared where the interrupt handler have already started to write the next event to the device. If set_next_event() is called in this window the value is only cached in the driver but not written. This leads to the board to misbehave, or worse lockup and produce a splat. rcu: INFO: rcu_preempt detected stalls on CPUs/tasks: rcu: 0-...!: (0 ticks this GP) idle=f5e0/0/0x0 softirq=519/519 fqs=0 (false positive?) rcu: (detected by 1, t=6502 jiffies, g=-595, q=77 ncpus=2) Sending NMI from CPU 1 to CPUs 0: NMI backtrace for cpu 0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.10.0-rc5-arm64-renesas-00019-g74a6f86eaf1c-dirty Freescale#20 Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tick_check_broadcast_expired+0xc/0x40 lr : cpu_idle_poll.isra.0+0x8c/0x168 sp : ffff800081c63d70 x29: ffff800081c63d70 x28: 00000000580000c8 x27: 00000000bfee5610 x26: 0000000000000027 x25: 0000000000000000 x24: 0000000000000000 x23: ffff00007fbb9100 x22: ffff8000818f1008 x21: ffff8000800ef07c x20: ffff800081c79ec0 x19: ffff800081c70c28 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffc2c717d8 x14: 0000000000000000 x13: ffff000009c18080 x12: ffff8000825f7fc0 x11: 0000000000000000 x10: ffff8000818f3cd4 x9 : 0000000000000028 x8 : ffff800081c79ec0 x7 : ffff800081c73000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : ffff7ffffe286000 x3 : 0000000000000000 x2 : ffff7ffffe286000 x1 : ffff800082972900 x0 : ffff8000818f1008 Call trace: tick_check_broadcast_expired+0xc/0x40 do_idle+0x9c/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x11c do_one_initcall+0x0/0x260 __primary_switched+0x80/0x88 rcu: rcu_preempt kthread timer wakeup didn't happen for 6501 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 rcu: Possible timer handling issue on cpu=0 timer-softirq=262 rcu: rcu_preempt kthread starved for 6502 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0 rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior. rcu: RCU grace-period kthread stack dump: task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 flags:0x00000008 Call trace: __switch_to+0xbc/0x100 __schedule+0x358/0xbe0 schedule+0x48/0x148 schedule_timeout+0xc4/0x138 rcu_gp_fqs_loop+0x12c/0x764 rcu_gp_kthread+0x208/0x298 kthread+0x10c/0x110 ret_from_fork+0x10/0x20 The design have been part of the driver since it was first merged in early 2009. It becomes increasingly harder to trigger the issue the older kernel version one tries. It only takes a few boots on v6.10-rc5, while hundreds of boots are needed to trigger it on v5.10. Close the race condition by using the CMT channel lock for the two competing sections. The channel lock was added to the driver after its initial design. Signed-off-by: Niklas Söderlund <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Daniel Lezcano <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 Freescale#1 __crash_kexec at ffffffff8c1338fa Freescale#2 panic at ffffffff8c1d69b9 Freescale#3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] Freescale#4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] Freescale#5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] Freescale#6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] Freescale#7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] Freescale#8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] Freescale#9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] Freescale#10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] Freescale#11 dio_complete at ffffffff8c2b9fa7 Freescale#12 do_blockdev_direct_IO at ffffffff8c2bc09f Freescale#13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] Freescale#14 generic_file_direct_write at ffffffff8c1dcf14 Freescale#15 __generic_file_write_iter at ffffffff8c1dd07b Freescale#16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] Freescale#17 aio_write at ffffffff8c2cc72e Freescale#18 kmem_cache_alloc at ffffffff8c248dde Freescale#19 do_io_submit at ffffffff8c2ccada Freescale#20 do_syscall_64 at ffffffff8c004984 Freescale#21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit bab4923 upstream. In the TRACE_EVENT(qdisc_reset) NULL dereference occurred from qdisc->dev_queue->dev <NULL> ->name This situation simulated from bunch of veths and Bluetooth disconnection and reconnection. During qdisc initialization, qdisc was being set to noop_queue. In veth_init_queue, the initial tx_num was reduced back to one, causing the qdisc reset to be called with noop, which led to the kernel panic. I've attached the GitHub gist link that C converted syz-execprogram source code and 3 log of reproduced vmcore-dmesg. https://gist.github.com/yskelg/cc64562873ce249cdd0d5a358b77d740 Yeoreum and I use two fuzzing tool simultaneously. One process with syz-executor : https://github.com/google/syzkaller $ ./syz-execprog -executor=./syz-executor -repeat=1 -sandbox=setuid \ -enable=none -collide=false log1 The other process with perf fuzzer: https://github.com/deater/perf_event_tests/tree/master/fuzzer $ perf_event_tests/fuzzer/perf_fuzzer I think this will happen on the kernel version. Linux kernel version +v6.7.10, +v6.8, +v6.9 and it could happen in v6.10. This occurred from 51270d5. I think this patch is absolutely necessary. Previously, It was showing not intended string value of name. I've reproduced 3 time from my fedora 40 Debug Kernel with any other module or patched. version: 6.10.0-0.rc2.20240608gitdc772f8237f9.29.fc41.aarch64+debug [ 5287.164555] veth0_vlan: left promiscuous mode [ 5287.164929] veth1_macvtap: left promiscuous mode [ 5287.164950] veth0_macvtap: left promiscuous mode [ 5287.164983] veth1_vlan: left promiscuous mode [ 5287.165008] veth0_vlan: left promiscuous mode [ 5287.165450] veth1_macvtap: left promiscuous mode [ 5287.165472] veth0_macvtap: left promiscuous mode [ 5287.165502] veth1_vlan: left promiscuous mode … [ 5297.598240] bridge0: port 2(bridge_slave_1) entered blocking state [ 5297.598262] bridge0: port 2(bridge_slave_1) entered forwarding state [ 5297.598296] bridge0: port 1(bridge_slave_0) entered blocking state [ 5297.598313] bridge0: port 1(bridge_slave_0) entered forwarding state [ 5297.616090] 8021q: adding VLAN 0 to HW filter on device bond0 [ 5297.620405] bridge0: port 1(bridge_slave_0) entered disabled state [ 5297.620730] bridge0: port 2(bridge_slave_1) entered disabled state [ 5297.627247] 8021q: adding VLAN 0 to HW filter on device team0 [ 5297.629636] bridge0: port 1(bridge_slave_0) entered blocking state … [ 5298.002798] bridge_slave_0: left promiscuous mode [ 5298.002869] bridge0: port 1(bridge_slave_0) entered disabled state [ 5298.309444] bond0 (unregistering): (slave bond_slave_0): Releasing backup interface [ 5298.315206] bond0 (unregistering): (slave bond_slave_1): Releasing backup interface [ 5298.320207] bond0 (unregistering): Released all slaves [ 5298.354296] hsr_slave_0: left promiscuous mode [ 5298.360750] hsr_slave_1: left promiscuous mode [ 5298.374889] veth1_macvtap: left promiscuous mode [ 5298.374931] veth0_macvtap: left promiscuous mode [ 5298.374988] veth1_vlan: left promiscuous mode [ 5298.375024] veth0_vlan: left promiscuous mode [ 5299.109741] team0 (unregistering): Port device team_slave_1 removed [ 5299.185870] team0 (unregistering): Port device team_slave_0 removed … [ 5300.155443] Bluetooth: hci3: unexpected cc 0x0c03 length: 249 > 1 [ 5300.155724] Bluetooth: hci3: unexpected cc 0x1003 length: 249 > 9 [ 5300.155988] Bluetooth: hci3: unexpected cc 0x1001 length: 249 > 9 …. [ 5301.075531] team0: Port device team_slave_1 added [ 5301.085515] bridge0: port 1(bridge_slave_0) entered blocking state [ 5301.085531] bridge0: port 1(bridge_slave_0) entered disabled state [ 5301.085588] bridge_slave_0: entered allmulticast mode [ 5301.085800] bridge_slave_0: entered promiscuous mode [ 5301.095617] bridge0: port 1(bridge_slave_0) entered blocking state [ 5301.095633] bridge0: port 1(bridge_slave_0) entered disabled state … [ 5301.149734] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.173234] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.180517] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link [ 5301.193481] hsr_slave_0: entered promiscuous mode [ 5301.204425] hsr_slave_1: entered promiscuous mode [ 5301.210172] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.210185] Cannot create hsr debugfs directory [ 5301.224061] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link [ 5301.246901] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link [ 5301.255934] team0: Port device team_slave_0 added [ 5301.256480] team0: Port device team_slave_1 added [ 5301.256948] team0: Port device team_slave_0 added … [ 5301.435928] hsr_slave_0: entered promiscuous mode [ 5301.446029] hsr_slave_1: entered promiscuous mode [ 5301.455872] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.455884] Cannot create hsr debugfs directory [ 5301.502664] hsr_slave_0: entered promiscuous mode [ 5301.513675] hsr_slave_1: entered promiscuous mode [ 5301.526155] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.526164] Cannot create hsr debugfs directory [ 5301.563662] hsr_slave_0: entered promiscuous mode [ 5301.576129] hsr_slave_1: entered promiscuous mode [ 5301.580259] debugfs: Directory 'hsr0' with parent 'hsr' already present! [ 5301.580270] Cannot create hsr debugfs directory [ 5301.590269] 8021q: adding VLAN 0 to HW filter on device bond0 [ 5301.595872] KASAN: null-ptr-deref in range [0x0000000000000130-0x0000000000000137] [ 5301.595877] Mem abort info: [ 5301.595881] ESR = 0x0000000096000006 [ 5301.595885] EC = 0x25: DABT (current EL), IL = 32 bits [ 5301.595889] SET = 0, FnV = 0 [ 5301.595893] EA = 0, S1PTW = 0 [ 5301.595896] FSC = 0x06: level 2 translation fault [ 5301.595900] Data abort info: [ 5301.595903] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000 [ 5301.595907] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 5301.595911] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 5301.595915] [dfff800000000026] address between user and kernel address ranges [ 5301.595971] Internal error: Oops: 0000000096000006 [Freescale#1] SMP … [ 5301.596076] CPU: 2 PID: 102769 Comm: syz-executor.3 Kdump: loaded Tainted: G W ------- --- 6.10.0-0.rc2.20240608gitdc772f8237f9.29.fc41.aarch64+debug Freescale#1 [ 5301.596080] Hardware name: VMware, Inc. VMware20,1/VBSA, BIOS VMW201.00V.21805430.BA64.2305221830 05/22/2023 [ 5301.596082] pstate: 01400005 (nzcv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 5301.596085] pc : strnlen+0x40/0x88 [ 5301.596114] lr : trace_event_get_offsets_qdisc_reset+0x6c/0x2b0 [ 5301.596124] sp : ffff8000beef6b40 [ 5301.596126] x29: ffff8000beef6b40 x28: dfff800000000000 x27: 0000000000000001 [ 5301.596131] x26: 6de1800082c62bd0 x25: 1ffff000110aa9e0 x24: ffff800088554f00 [ 5301.596136] x23: ffff800088554ec0 x22: 0000000000000130 x21: 0000000000000140 [ 5301.596140] x20: dfff800000000000 x19: ffff8000beef6c60 x18: ffff7000115106d8 [ 5301.596143] x17: ffff800121bad000 x16: ffff800080020000 x15: 0000000000000006 [ 5301.596147] x14: 0000000000000002 x13: ffff0001f3ed8d14 x12: ffff700017ddeda5 [ 5301.596151] x11: 1ffff00017ddeda4 x10: ffff700017ddeda4 x9 : ffff800082cc5eec [ 5301.596155] x8 : 0000000000000004 x7 : 00000000f1f1f1f1 x6 : 00000000f2f2f200 [ 5301.596158] x5 : 00000000f3f3f3f3 x4 : ffff700017dded80 x3 : 00000000f204f1f1 [ 5301.596162] x2 : 0000000000000026 x1 : 0000000000000000 x0 : 0000000000000130 [ 5301.596166] Call trace: [ 5301.596175] strnlen+0x40/0x88 [ 5301.596179] trace_event_get_offsets_qdisc_reset+0x6c/0x2b0 [ 5301.596182] perf_trace_qdisc_reset+0xb0/0x538 [ 5301.596184] __traceiter_qdisc_reset+0x68/0xc0 [ 5301.596188] qdisc_reset+0x43c/0x5e8 [ 5301.596190] netif_set_real_num_tx_queues+0x288/0x770 [ 5301.596194] veth_init_queues+0xfc/0x130 [veth] [ 5301.596198] veth_newlink+0x45c/0x850 [veth] [ 5301.596202] rtnl_newlink_create+0x2c8/0x798 [ 5301.596205] __rtnl_newlink+0x92c/0xb60 [ 5301.596208] rtnl_newlink+0xd8/0x130 [ 5301.596211] rtnetlink_rcv_msg+0x2e0/0x890 [ 5301.596214] netlink_rcv_skb+0x1c4/0x380 [ 5301.596225] rtnetlink_rcv+0x20/0x38 [ 5301.596227] netlink_unicast+0x3c8/0x640 [ 5301.596231] netlink_sendmsg+0x658/0xa60 [ 5301.596234] __sock_sendmsg+0xd0/0x180 [ 5301.596243] __sys_sendto+0x1c0/0x280 [ 5301.596246] __arm64_sys_sendto+0xc8/0x150 [ 5301.596249] invoke_syscall+0xdc/0x268 [ 5301.596256] el0_svc_common.constprop.0+0x16c/0x240 [ 5301.596259] do_el0_svc+0x48/0x68 [ 5301.596261] el0_svc+0x50/0x188 [ 5301.596265] el0t_64_sync_handler+0x120/0x130 [ 5301.596268] el0t_64_sync+0x194/0x198 [ 5301.596272] Code: eb15001f 54000120 d343fc02 12000801 (38f46842) [ 5301.596285] SMP: stopping secondary CPUs [ 5301.597053] Starting crashdump kernel... [ 5301.597057] Bye! After applying our patch, I didn't find any kernel panic errors. We've found a simple reproducer # echo 1 > /sys/kernel/debug/tracing/events/qdisc/qdisc_reset/enable # ip link add veth0 type veth peer name veth1 Error: Unknown device type. However, without our patch applied, I tested upstream 6.10.0-rc3 kernel using the qdisc_reset event and the ip command on my qemu virtual machine. This 2 commands makes always kernel panic. Linux version: 6.10.0-rc3 [ 0.000000] Linux version 6.10.0-rc3-00164-g44ef20baed8e-dirty (paran@fedora) (gcc (GCC) 14.1.1 20240522 (Red Hat 14.1.1-4), GNU ld version 2.41-34.fc40) Freescale#20 SMP PREEMPT Sat Jun 15 16:51:25 KST 2024 Kernel panic message: [ 615.236484] Internal error: Oops: 0000000096000005 [Freescale#1] PREEMPT SMP [ 615.237250] Dumping ftrace buffer: [ 615.237679] (ftrace buffer empty) [ 615.238097] Modules linked in: veth crct10dif_ce virtio_gpu virtio_dma_buf drm_shmem_helper drm_kms_helper zynqmp_fpga xilinx_can xilinx_spi xilinx_selectmap xilinx_core xilinx_pr_decoupler versal_fpga uvcvideo uvc videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videodev videobuf2_common mc usbnet deflate zstd ubifs ubi rcar_canfd rcar_can omap_mailbox ntb_msi_test ntb_hw_epf lattice_sysconfig_spi lattice_sysconfig ice40_spi gpio_xilinx dwmac_altr_socfpga mdio_regmap stmmac_platform stmmac pcs_xpcs dfl_fme_region dfl_fme_mgr dfl_fme_br dfl_afu dfl fpga_region fpga_bridge can can_dev br_netfilter bridge stp llc atl1c ath11k_pci mhi ath11k_ahb ath11k qmi_helpers ath10k_sdio ath10k_pci ath10k_core ath mac80211 libarc4 cfg80211 drm fuse backlight ipv6 Jun 22 02:36:5[3 6k152.62-4sm98k4-0k]v kCePUr:n e1l :P IUDn:a b4le6 8t oC ohmma: nidpl eN oketr nteali nptaedg i6n.g1 0re.0q-urecs3t- 0at0 1v6i4r-tgu4a4le fa2d0dbraeeds0se-dir tyd f#f2f08 615.252376] Hardware name: linux,dummy-virt (DT) [ 615.253220] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 615.254433] pc : strnlen+0x6c/0xe0 [ 615.255096] lr : trace_event_get_offsets_qdisc_reset+0x94/0x3d0 [ 615.256088] sp : ffff800080b269a0 [ 615.256615] x29: ffff800080b269a0 x28: ffffc070f3f98500 x27: 0000000000000001 [ 615.257831] x26: 0000000000000010 x25: ffffc070f3f98540 x24: ffffc070f619cf60 [ 615.259020] x23: 0000000000000128 x22: 0000000000000138 x21: dfff800000000000 [ 615.260241] x20: ffffc070f631ad00 x19: 0000000000000128 x18: ffffc070f448b800 [ 615.261454] x17: 0000000000000000 x16: 0000000000000001 x15: ffffc070f4ba2a90 [ 615.262635] x14: ffff700010164d73 x13: 1ffff80e1e8d5eb3 x12: 1ffff00010164d72 [ 615.263877] x11: ffff700010164d72 x10: dfff800000000000 x9 : ffffc070e85d6184 [ 615.265047] x8 : ffffc070e4402070 x7 : 000000000000f1f1 x6 : 000000001504a6d3 [ 615.266336] x5 : ffff28ca21122140 x4 : ffffc070f5043ea8 x3 : 0000000000000000 [ 615.267528] x2 : 0000000000000025 x1 : 0000000000000000 x0 : 0000000000000000 [ 615.268747] Call trace: [ 615.269180] strnlen+0x6c/0xe0 [ 615.269767] trace_event_get_offsets_qdisc_reset+0x94/0x3d0 [ 615.270716] trace_event_raw_event_qdisc_reset+0xe8/0x4e8 [ 615.271667] __traceiter_qdisc_reset+0xa0/0x140 [ 615.272499] qdisc_reset+0x554/0x848 [ 615.273134] netif_set_real_num_tx_queues+0x360/0x9a8 [ 615.274050] veth_init_queues+0x110/0x220 [veth] [ 615.275110] veth_newlink+0x538/0xa50 [veth] [ 615.276172] __rtnl_newlink+0x11e4/0x1bc8 [ 615.276944] rtnl_newlink+0xac/0x120 [ 615.277657] rtnetlink_rcv_msg+0x4e4/0x1370 [ 615.278409] netlink_rcv_skb+0x25c/0x4f0 [ 615.279122] rtnetlink_rcv+0x48/0x70 [ 615.279769] netlink_unicast+0x5a8/0x7b8 [ 615.280462] netlink_sendmsg+0xa70/0x1190 Yeoreum and I don't know if the patch we wrote will fix the underlying cause, but we think that priority is to prevent kernel panic happening. So, we're sending this patch. Fixes: 51270d5 ("tracing/net_sched: Fix tracepoints that save qdisc_dev() as a string") Link: https://lore.kernel.org/lkml/[email protected]/t/ Cc: [email protected] Tested-by: Yunseong Kim <[email protected]> Signed-off-by: Yunseong Kim <[email protected]> Signed-off-by: Yeoreum Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 3b65644 ] The RISC-V kernel already has checks to ensure that memory which would lie outside of the linear mapping is not used. However those checks use memory_limit, which is used to implement the mem= kernel command line option (to limit the total amount of memory, not its address range). When memory is made up of two or more non-contiguous memory banks this check is incorrect. Two changes are made here: - add a call in setup_bootmem() to memblock_cap_memory_range() which will cause any memory which falls outside the linear mapping to be removed from the memory regions. - remove the check in create_linear_mapping_page_table() which was intended to remove memory which is outside the liner mapping based on memory_limit, as it is no longer needed. Note a check for mapping more memory than memory_limit (to implement mem=) is unnecessary because of the existing call to memblock_enforce_memory_limit(). This issue was seen when booting on a SV39 platform with two memory banks: 0x00,80000000 1GiB 0x20,00000000 32GiB This memory range is 158GiB from top to bottom, but the linear mapping is limited to 128GiB, so the lower block of RAM will be mapped at PAGE_OFFSET, and the upper block straddles the top of the linear mapping. This causes the following Oops: [ 0.000000] Linux version 6.10.0-rc2-gd3b8dd5b51dd-dirty ([email protected]) (riscv64-codasip-linux-gcc (GCC) 13.2.0, GNU ld (GNU Binutils) 2.41.0.20231213) Freescale#20 SMP Sat Jun 22 11:34:22 BST 2024 [ 0.000000] memblock_add: [0x0000000080000000-0x00000000bfffffff] early_init_dt_add_memory_arch+0x4a/0x52 [ 0.000000] memblock_add: [0x0000002000000000-0x00000027ffffffff] early_init_dt_add_memory_arch+0x4a/0x52 ... [ 0.000000] memblock_alloc_try_nid: 23724 bytes align=0x8 nid=-1 from=0x0000000000000000 max_addr=0x0000000000000000 early_init_dt_alloc_memory_arch+0x1e/0x48 [ 0.000000] memblock_reserve: [0x00000027ffff5350-0x00000027ffffaffb] memblock_alloc_range_nid+0xb8/0x132 [ 0.000000] Unable to handle kernel paging request at virtual address fffffffe7fff5350 [ 0.000000] Oops [Freescale#1] [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.10.0-rc2-gd3b8dd5b51dd-dirty Freescale#20 [ 0.000000] Hardware name: codasip,a70x (DT) [ 0.000000] epc : __memset+0x8c/0x104 [ 0.000000] ra : memblock_alloc_try_nid+0x74/0x84 [ 0.000000] epc : ffffffff805e88c8 ra : ffffffff806148f6 sp : ffffffff80e03d50 [ 0.000000] gp : ffffffff80ec4158 tp : ffffffff80e0bec0 t0 : fffffffe7fff52f8 [ 0.000000] t1 : 00000027ffffb000 t2 : 5f6b636f6c626d65 s0 : ffffffff80e03d90 [ 0.000000] s1 : 0000000000005cac a0 : fffffffe7fff5350 a1 : 0000000000000000 [ 0.000000] a2 : 0000000000005cac a3 : fffffffe7fffaff8 a4 : 000000000000002c [ 0.000000] a5 : ffffffff805e88c8 a6 : 0000000000005cac a7 : 0000000000000030 [ 0.000000] s2 : fffffffe7fff5350 s3 : ffffffffffffffff s4 : 0000000000000000 [ 0.000000] s5 : ffffffff8062347e s6 : 0000000000000000 s7 : 0000000000000001 [ 0.000000] s8 : 0000000000002000 s9 : 00000000800226d0 s10: 0000000000000000 [ 0.000000] s11: 0000000000000000 t3 : ffffffff8080a928 t4 : ffffffff8080a928 [ 0.000000] t5 : ffffffff8080a928 t6 : ffffffff8080a940 [ 0.000000] status: 0000000200000100 badaddr: fffffffe7fff5350 cause: 000000000000000f [ 0.000000] [<ffffffff805e88c8>] __memset+0x8c/0x104 [ 0.000000] [<ffffffff8062349c>] early_init_dt_alloc_memory_arch+0x1e/0x48 [ 0.000000] [<ffffffff8043e892>] __unflatten_device_tree+0x52/0x114 [ 0.000000] [<ffffffff8062441e>] unflatten_device_tree+0x9e/0xb8 [ 0.000000] [<ffffffff806046fe>] setup_arch+0xd4/0x5bc [ 0.000000] [<ffffffff806007aa>] start_kernel+0x76/0x81a [ 0.000000] Code: b823 02b2 bc23 02b2 b023 04b2 b423 04b2 b823 04b2 (bc23) 04b2 [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] Kernel panic - not syncing: Attempted to kill the idle task! [ 0.000000] ---[ end Kernel panic - not syncing: Attempted to kill the idle task! ]--- The problem is that memblock (unaware that some physical memory cannot be used) has allocated memory from the top of memory but which is outside the linear mapping region. Signed-off-by: Stuart Menefy <[email protected]> Fixes: c99127c ("riscv: Make sure the linear mapping does not use the kernel mapping") Reviewed-by: David McKay <[email protected]> Reviewed-by: Alexandre Ghiti <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Palmer Dabbelt <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit db19d3a ] There is a race condition in the CMT interrupt handler. In the interrupt handler the driver sets a driver private flag, FLAG_IRQCONTEXT. This flag is used to indicate any call to set_next_event() should not be directly propagated to the device, but instead cached. This is done as the interrupt handler itself reprograms the device when needed before it completes and this avoids this operation to take place twice. It is unclear why this design was chosen, my suspicion is to allow the struct clock_event_device.event_handler callback, which is called while the FLAG_IRQCONTEXT is set, can update the next event without having to write to the device twice. Unfortunately there is a race between when the FLAG_IRQCONTEXT flag is set and later cleared where the interrupt handler have already started to write the next event to the device. If set_next_event() is called in this window the value is only cached in the driver but not written. This leads to the board to misbehave, or worse lockup and produce a splat. rcu: INFO: rcu_preempt detected stalls on CPUs/tasks: rcu: 0-...!: (0 ticks this GP) idle=f5e0/0/0x0 softirq=519/519 fqs=0 (false positive?) rcu: (detected by 1, t=6502 jiffies, g=-595, q=77 ncpus=2) Sending NMI from CPU 1 to CPUs 0: NMI backtrace for cpu 0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.10.0-rc5-arm64-renesas-00019-g74a6f86eaf1c-dirty Freescale#20 Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tick_check_broadcast_expired+0xc/0x40 lr : cpu_idle_poll.isra.0+0x8c/0x168 sp : ffff800081c63d70 x29: ffff800081c63d70 x28: 00000000580000c8 x27: 00000000bfee5610 x26: 0000000000000027 x25: 0000000000000000 x24: 0000000000000000 x23: ffff00007fbb9100 x22: ffff8000818f1008 x21: ffff8000800ef07c x20: ffff800081c79ec0 x19: ffff800081c70c28 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffc2c717d8 x14: 0000000000000000 x13: ffff000009c18080 x12: ffff8000825f7fc0 x11: 0000000000000000 x10: ffff8000818f3cd4 x9 : 0000000000000028 x8 : ffff800081c79ec0 x7 : ffff800081c73000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : ffff7ffffe286000 x3 : 0000000000000000 x2 : ffff7ffffe286000 x1 : ffff800082972900 x0 : ffff8000818f1008 Call trace: tick_check_broadcast_expired+0xc/0x40 do_idle+0x9c/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x11c do_one_initcall+0x0/0x260 __primary_switched+0x80/0x88 rcu: rcu_preempt kthread timer wakeup didn't happen for 6501 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 rcu: Possible timer handling issue on cpu=0 timer-softirq=262 rcu: rcu_preempt kthread starved for 6502 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0 rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior. rcu: RCU grace-period kthread stack dump: task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 flags:0x00000008 Call trace: __switch_to+0xbc/0x100 __schedule+0x358/0xbe0 schedule+0x48/0x148 schedule_timeout+0xc4/0x138 rcu_gp_fqs_loop+0x12c/0x764 rcu_gp_kthread+0x208/0x298 kthread+0x10c/0x110 ret_from_fork+0x10/0x20 The design have been part of the driver since it was first merged in early 2009. It becomes increasingly harder to trigger the issue the older kernel version one tries. It only takes a few boots on v6.10-rc5, while hundreds of boots are needed to trigger it on v5.10. Close the race condition by using the CMT channel lock for the two competing sections. The channel lock was added to the driver after its initial design. Signed-off-by: Niklas Söderlund <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Daniel Lezcano <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

MaxKrummenacher and others added 9 commits December 13, 2017 09:20

video: mxsfb: add compile dependencies

94a22d9

mxsfb seems to have dependencies into mxcfb (it requires mxc_dispdrv_gethandle), hence compile mxc_dispdrv.c unconditionally. Signed-off-by: Stefan Agner <[email protected]> Acked-by: Max Krummenacher <[email protected]>

video: mxsfb: simplify parsing

65be28e

Use the timing count from the parsed struct display_timings instead of looping through the device tree again. Signed-off-by: Stefan Agner <[email protected]> Acked-by: Max Krummenacher <[email protected]>

ARM: dts: imx6ull: include all needed definitions

479e0ba

The file uses linux,keycode = <KEY_POWER>;, so include the header which defines KEY_POWER. Signed-off-by: Max Krummenacher <[email protected]> Signed-off-by: Stefan Agner <[email protected]>

otavio merged commit f7c79b9 into Freescale:4.9-1.0.x-imx Dec 13, 2017

agners pushed a commit to agners/linux-fslc that referenced this pull request Jan 24, 2018

Merge pull request Freescale#20 from falstaff84/4.9-1.0.x-imx-fixes

effee16

4.9-1.0.x-imx fixes from Toradex branch

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

4.9-1.0.x-imx fixes from Toradex branch #20

4.9-1.0.x-imx fixes from Toradex branch #20

agners commented Dec 13, 2017

4.9-1.0.x-imx fixes from Toradex branch #20

4.9-1.0.x-imx fixes from Toradex branch #20

Conversation

agners commented Dec 13, 2017