Add files via upload

altitude_control/MS5607_FH_Example.ino

@@ -0,0 +1,151 @@
+#include <Wire.h>
+#include <math.h>
+
+
+//#define ADDRESS 0x76 // Address of Parallax - Pressure Sensor MS5607 REV A
+#define ADDRESS 0x77 // Address of Far Horizons - Pressure Sensor MS5607 REV B
+
+uint32_t D1 = 0;
+uint32_t D2 = 0;
+float dT = 0;
+int32_t TEMP = 0;
+float OFF = 0; 
+float SENS = 0; 
+float P = 0;
+float T2  = 0;
+float OFF2  = 0;
+float SENS2 = 0;
+uint16_t C[7];
+//int count = 0;
+
+float Temperature;
+float Pressure;
+
+
+
+
+void setup() {
+
+
+
+// Disable internal pullups, 10Kohms are on the breakout
+ PORTC |= (1 << 4);
+ PORTC |= (1 << 5);
+
+  Wire.begin();
+  Serial.begin(57600); //9600 changed 'cos of timing?
+  delay(1000); //Give the open log a second to get in gear. 
+  initial(ADDRESS);
+}
+
+void loop()
+{
+//count = count + 1;
+
+/*******************************************************************************/
+/**************                PRESSURE                   **********************/
+/*******************************************************************************/
+
+  D1 = getVal(ADDRESS, 0x48); // Pressure raw
+  D2 = getVal(ADDRESS, 0x58);// Temperature raw
+
+  dT   = (float)D2 - ((uint32_t)C[5] * 256);
+  OFF  = ((float)C[2] * 131072) + ((dT * C[4]) / 64);
+  SENS = ((float)C[1] * 65536) + (dT * C[3] / 128);
+
+  TEMP = (int64_t)dT * (int64_t)C[6] / 8388608 + 2000;
+
+ if(TEMP < 2000) // if temperature lower than 20 Celsius 
+  {
+
+    T2=pow(dT,2)/2147483648;
+    OFF2=61*pow((TEMP-2000),2)/16;
+    SENS2=2*pow((TEMP-2000),2);
+
+   if(TEMP < -1500) // if temperature lower than -15 Celsius 
+    {
+     OFF2=OFF2+15*pow((TEMP+1500),2);
+     SENS2=SENS2+8*pow((TEMP+1500),2);
+    }
+
+    TEMP = TEMP - T2;
+    OFF = OFF - OFF2; 
+    SENS = SENS - SENS2;   
+  }
+
+  Temperature = (float)TEMP / 100;  
+  P  = (D1 * SENS / 2097152 - OFF) / 32768;
+  Pressure = (float)P / 100;
+
+//  Serial.print("$FHDAT");
+//  Serial.print(",");
+//  Serial.print(count);
+  Serial.print("\t");
+  Serial.print(Temperature);
+  Serial.print("\t");
+  Serial.println(Pressure);
+
+  /* RESET THE CORECTION FACTORS */
+
+    T2 = 0;
+    OFF2 = 0;
+    SENS2 = 0;
+
+  delay(100);
+} /* END OF ARDUINO LOOP */
+
+long getVal(int address, byte code)
+{
+  unsigned long ret = 0;
+  Wire.beginTransmission(address);
+  Wire.write(code);
+  Wire.endTransmission();
+  delay(10);
+  // start read sequence
+  Wire.beginTransmission(address);
+  Wire.write((byte) 0x00);
+  Wire.endTransmission();
+  Wire.beginTransmission(address);
+  Wire.requestFrom(address, (int)3);
+  if (Wire.available() >= 3)
+  {
+    ret = Wire.read() * (unsigned long)65536 + Wire.read() * (unsigned long)256 + Wire.read();
+  }
+  else {
+    ret = -1;
+  }
+  Wire.endTransmission();
+  return ret;
+}
+
+void initial(uint8_t address)
+{
+  //Serial.println();
+  //Serial.println("PRESSURE SENSOR PROM COEFFICIENTS");
+
+  Wire.beginTransmission(address);
+  Wire.write(0x1E); // reset
+  Wire.endTransmission();
+  delay(10);
+
+
+  for (int i=0; i<6  ; i++) {
+
+    Wire.beginTransmission(address);
+    Wire.write(0xA2 + (i * 2));
+    Wire.endTransmission();
+
+    Wire.beginTransmission(address);
+    Wire.requestFrom(address, (uint8_t) 6);
+    delay(1);
+    if(Wire.available())
+    {
+       C[i+1] = Wire.read() << 8 | Wire.read();
+    }
+    else {
+      Serial.println("Error reading PROM 1"); // error reading the PROM or communicating with the device
+    }
+    //Serial.println(C[i+1]);   // Prints out the coefficients.
+  }
+  //Serial.println();
+}

altitude_control/SD_Card_Read_Write.ino

@@ -0,0 +1,123 @@
+/*
+  SD card read/write
+ This example shows how to read and write data to and from an SD card file   
+ The circuit:
+ */
+
+#include <SD.h>
+#include <SPI.h>
+
+String dataString =""; // holds the data to be written to the SD card
+float sensorReading1 = 1.00; // value read from your first sensor
+float sensorReading2 = 0.00; // value read from your second sensor
+float sensorReading3 = 0.00; // value read from your third sensor
+float sensorReading4 = 0.00; // value read from your third sensor
+
+File sensorData;
+
+File myFile;
+const int chipSelect= 15;
+
+//const int chipSelect = BUILTIN_SDCARD; //for Teensy3.5
+
+
+void setup(){
+  Serial.begin(115200);
+  sd_setup();
+
+}
+
+
+
+
+void loop()
+{
+  prepare_data();
+  saveData(); // save to SD card
+}
+
+
+
+
+//////////////////////////////////////////////////////////////////////////////////////////////
+//                              Functions                                                  ///
+//////////////////////////////////////////////////////////////////////////////////////////////
+
+////////////////////////////////////////////////////
+//SD Initialize and creates a file               ///
+////////////////////////////////////////////////////
+void sd_setup()
+{
+
+  Serial.print("Initializing SD card...");
+  // IF FAILURE OCCURS: 
+    if (!SD.begin(chipSelect)) {
+      Serial.println("initialization failed!");
+      return;
+    }
+
+  Serial.println("initialization done.");
+  sensorData = SD.open("data.csv", FILE_WRITE);
+  sensorData.close();
+  //read_SD_Directory(); 
+}
+
+////////////////////////////////////////////////////
+//Prepares the Data                              ///
+////////////////////////////////////////////////////
+void prepare_data(){
+    // build the data string
+  dataString = String(sensorReading1) + "," + String(sensorReading2) + "," + String(sensorReading3) +  "," + String(sensorReading4) +  "," ;
+  Serial.println(dataString); //Only to show on the Serial Monitor.
+
+}
+
+////////////////////////////////////////////////////
+//Saves the Data                                 ///
+////////////////////////////////////////////////////
+void saveData(){
+    if(SD.exists("data.csv")){ // check the card is still there
+      // now append new data file
+      Serial.println("data.csv exists");
+      sensorData = SD.open("data.csv", FILE_WRITE);
+      if (sensorData){
+      sensorData.println(dataString);
+      sensorData.close(); // close the file
+    }
+  }
+  else{
+    Serial.println("Error writing to file !");
+  }
+}
+
+////////////////////////////////////////////////////
+//Reads the SD Directory                         ///
+////////////////////////////////////////////////////
+//void read_SD_Directory(){
+//    // Read the contents of the SD card
+//    File root = SD.open("/");
+//    root.rewindDirectory();
+//    listFiles(root);
+//    root.close();
+//  
+//}
+
+//////////////////////////////////////////////////////////
+//Reads the files and prints onto Serial Monitors        ///
+//////////////////////////////////////////////////////////
+//String listFiles(File dir) 
+//{
+//  while(true) {
+//     File entry = dir.openNextFile();
+//     if (! entry) {
+//      Serial.println("NO MORE FILES!");
+//       // no more files
+//       break;
+//     }
+//     // convert to string to make it easier to work with...
+//     String entryName = (String)entry.name();
+//     Serial.println("FOUND: " + entryName);
+//     entry.close();
+//     Serial.println("closed: ");
+//   }
+//}