printer.cfg

#################################################
#                     By                        #
#             Ethereal Project 3D               #
#          www.etherealproject3d.com            #
#     www.youtube.com/c/etherealproject3d       #
#################################################

############################################################################################################################################
#                                                                                                                                          #
#                                                                    NOTE:                                                                 #
#   I used the printer.cfg created by "freakydude" from the Klipper gethub page as a starting point and edited it for this application.    #
#                                                          You can find the origional here;                                                #
#                     https://github.com/Klipper3d/klipper/blob/master/config/printer-artillery-sidewinder-x2-2022.cfg                     #
############################################################################################################################################ 

# This file contains pin mappings for the Artillery Sidewinder X2 (2022) with a Artillery_Ruby-v1.2 board.
# To use this config, during "make menuconfig"

#                         Klipper Firmware Configuration
#[*] Enable extra low-level configuration options
#    Micro-controller Architecture (STMicroelectronics STM32)  --->
#    Processor model (STM32F401)  --->
#    Bootloader offset (No bootloader)  --->
#    Clock Reference (8 MHz crystal)  --->
#    Communication interface (USB (on PA11/PA12))  --->
#    USB ids  --->
#()  GPIO pins to set at micro-controller startup

       
[include mainsail.cfg]
[include start.cfg]
[include end.cfg]
[include macros.cfg]
#[include adxl.cfg]
[pause_resume]
[display_status]
[virtual_sdcard]
path: ~/printer_data/gcodes
on_error_gcode: CANCEL_PRINT

[mcu]
serial: /dev/serial/by-id/usb-Klipper_stm32f401xc_170043000351383532393932-if00

[printer]
kinematics: cartesian
max_velocity: 250
max_accel: 6500
max_z_velocity: 50
max_z_accel: 400
square_corner_velocity: 5.0

[input_shaper]
shaper_freq_x: 59.2
shaper_type_x: mzv
shaper_freq_y: 76
shaper_type_y: 2hump_ei

[stepper_x]
step_pin: !PB14
dir_pin: PB13
enable_pin: !PB15
microsteps: 16
rotation_distance: 39.94
endstop_pin: !PA2
position_endstop: 0
position_max: 220
homing_speed: 100
second_homing_speed: 125

[stepper_y]
step_pin: PB10
dir_pin: PB2
enable_pin: !PB12
microsteps: 16
rotation_distance: 39.94
endstop_pin: !PA1
position_endstop: 0
position_max: 220
homing_speed: 125
second_homing_speed: 10

[stepper_z]
step_pin: PB0
dir_pin: !PC5
enable_pin: !PB1
microsteps: 16
rotation_distance: 7.96
endstop_pin: probe:z_virtual_endstop
position_max: 250
position_min: -5
homing_speed: 25
second_homing_speed: 10

[safe_z_home]
home_xy_position:110,110
speed: 200
z_hop: 10
z_hop_speed: 10

[extruder]
step_pin: PA7
dir_pin: PA6
enable_pin: !PC4
microsteps: 16
rotation_distance: 21.8667
gear_ratio: 66:22
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC9
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC0
#control: pid
#pid_kp: 23.509
#pid_ki: 1.438
#pid_kd: 96.092
min_temp: 0
max_temp: 300
max_extrude_only_distance: 1000
#pressure_advance: 0.068

[heater_bed]
heater_pin: PA8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC1
#control: pid
#pid_kp: 42.365
#pid_ki: 0.545
#pid_kd: 822.940
min_temp: 0
max_temp: 130

[fan]
pin: PC8
off_below: 0.1

[heater_fan extruder]
pin: PC7
off_below: 0.2

[controller_fan case]
pin: PC6
off_below: 0.3
idle_speed: 0.0

[temperature_sensor mainboard]
sensor_type: temperature_mcu
min_temp: 10
max_temp: 60

[bltouch]
sensor_pin: PC2
control_pin: PC3
x_offset: 27.25
y_offset: -12.8
#z_offset: 2.0
speed: 10
samples: 2
sample_retract_dist: 8
samples_tolerance: 0.050
samples_tolerance_retries: 3

[bed_mesh]
speed: 150
horizontal_move_z: 10
mesh_min: 30, 15
mesh_max: 210,190
probe_count: 5
fade_start: 1
fade_end: 10
fade_target: 0
mesh_pps: 2
algorithm: bicubic

[bed_screws]
screw1: 45,45
screw1_name: front left
screw2: 185,45
screw2_name: front right
screw3: 185,185
screw3_name: back right
screw4: 45,185
screw4_name: back left
speed: 100.0

[screws_tilt_adjust]
screw1: 45,45
screw1_name: front left
screw2: 185,45
screw2_name: front right
screw3: 185,185
screw3_name: back left
screw4: 45,185
screw4_name: back right
speed: 100.0
screw_thread: CW-M5	

[neopixel extruder]
pin: PB7
initial_RED: 1.0
initial_GREEN: 0
initial_BLUE: 0

[delayed_gcode Welcome_0]
initial_duration: 0
gcode:
  SET_LED LED=extruder RED=1 GREEN=0 BLUE=0

[delayed_gcode Welcome_1]
initial_duration: 0.5
gcode:
  SET_LED LED=extruder RED=0 GREEN=1 BLUE=0

[delayed_gcode Welcome_2]
initial_duration: 1
gcode:
  SET_LED LED=extruder RED=0 GREEN=0 BLUE=1

[delayed_gcode Welcome_3]
initial_duration: 1.5
gcode:
  SET_LED LED=extruder RED=1 GREEN=1 BLUE=1

[delayed_gcode Welcome_4]
initial_duration: 8
gcode:
  SET_LED LED=extruder RED=0.078 GREEN=0.568 BLUE=1

[filament_switch_sensor my_sensor]
#Move filament runout sensor from TFT to X+ endstop pin. Uncomment all but this line if you want to use this

pause_on_runout: True

runout_gcode: PAUSE

insert_gcode: RESUME

switch_pin: PA0


#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bltouch]
#*# z_offset = 2.596
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 20.701
#*# pid_ki = 1.211
#*# pid_kd = 88.497
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 47.557
#*# pid_ki = 1.215
#*# pid_kd = 465.467
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  0.059700, 0.014925, 0.058456, 0.070894, 0.059700
#*# 	  0.135569, 0.042288, 0.070894, 0.049750, 0.048506
#*# 	  0.161688, 0.059700, 0.043531, 0.021144, 0.021144
#*# 	  0.177856, 0.073381, 0.067163, 0.063431, 0.052238
#*# 	  0.094525, 0.042288, 0.060944, 0.029850, 0.043531
#*# x_count = 5
#*# y_count = 5
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 30.0
#*# max_x = 210.0
#*# min_y = 15.0
#*# max_y = 190.0