1.4.134-DEV

Full Changelog: 1.4.133-DEV...1.4.134-DEV

1.4.133-DEV

Full Changelog: 1.4.132-DEV...1.4.133-DEV

1.4.132-DEV

Full Changelog: 1.4.131-DEV...1.4.132-DEV

1.4.131-DEV

Full Changelog: 1.4.130-DEV...1.4.131-DEV

1.4.130-DEV

Full Changelog: 1.4.129-DEV...1.4.130-DEV

1.4.129-DEV

• STEAPP-837: Перенести модель в центр стола. - moved the model nozzle_offset to the center of the 3d module by @SokolovJek in #221
• STEAPP-728: ПГ не приезжает вперед для крепления ДАКа, при автокалибровке стола. - Added moving the printhead before calibrating module_3d to install the sensor by @SokolovJek in #218

Full Changelog: 1.4.128-DEV...1.4.129-DEV

1.4.128-DEV

• STEAPP-839: В менеджере "установки нулевой точки", перемещать ПГ ближе к пользователю. - Added moving the printhead after calibrating to remove the sensor by @SokolovJek in #222
• STEAPP-837: Перенести модель в центр стола. - moved the model nozzle_offset to the center of the 3d module by @SokolovJek in #221
• STEAPP-728: ПГ не приезжает вперед для крепления ДАКа, при автокалибровке стола. - Added moving the printhead before calibrating module_3d to install the sensor by @SokolovJek in #218

Full Changelog: 1.4.127-DEV...1.4.128-DEV

1.4.127-DEV

Full Changelog: 1.4.126-DEV...1.4.127-DEV

1.4.126-DEV

• STEAPP-831: Отсутствует код у ошибки - added error code for the error Heater extruder1 not heating at expected rate by @SokolovJek in #217
• STEAPP-809: ПГ врезается в деталь, при старте печати в режиме 3D, по алгоритму восстановления после отключения - Z-axis movements before printing have been removed. Because the printhead crashes into the model after the print is restored due to a power outage by @SokolovJek in #220
• STEAPP-829: Добавить проверку, на ввод больших значений в команду SET_ECENTRICCITY - added checking the params before calculate ECCENTRICITY by @SokolovJek in #219

Full Changelog: 1.4.125-DEV...1.4.126-DEV

1.4.125-DEV

• STEAPP-831: Отсутствует код у ошибки - added error code for the error Heater extruder1 not heating at expected rate by @SokolovJek in #217
• STEAPP-809: ПГ врезается в деталь, при старте печати в режиме 3D, по алгоритму восстановления после отключения - Z-axis movements before printing have been removed. Because the printhead crashes into the model after the print is restored due to a power outage by @SokolovJek in #220
• STEAPP-829: Добавить проверку, на ввод больших значений в команду SET_ECENTRICCITY - added checking the params before calculate ECCENTRICITY by @SokolovJek in #219

Full Changelog: 1.4.124-DEV...1.4.125-DEV