| layout | title |
|---|---|
documentation |
ZSE40 v2 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZSE40 v2, manufactured by Zooz with the thing type UID of zooz_zse40v2242_24_002.
This version of the device is limited to firmware version 24.2
The device is in the category of Sensor, defining Device used to measure something.
The ZSE40 v2 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The ZSE40 v2 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
- 4 smart sensors in 1 compact device
- 7 levels of motion sensitivity to choose from
- 3 modes for motion / temp led indicator notifications
- Built-in tamper protection
- Low battery alerts
- Z-Wave Plus with improved 500 chip for faster and safer wireless communication
- Security enabled Z-Wave device with AES signal encryption
Factory Reset
If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, remove the back cover to trigger tamper switch. Press and release the Z-Wave button 10 TIMES quickly (within 10 seconds).
NOTE: All previously recorded activity and custom settings will be erased from the device’s memory.
- Install the batteries and bring the 4-in-1 sensor as close to your Z-Wave gateway controller as possible
- Put your Z-Wave controller in inclusion mode
- Press and release the Z-Wave button TWICE quickly. The sensor will enter secure inclusion mode.
- A new 4-in-1 sensor should appear on your controller’s device list
Q: I have not been able to add the device to my network after several attempts, what do I do now?
A: If you are unable to include the Z-Wave sensor to your controller, please try one of the following:
- Bring the 4-in-1 sensor closer to your Z-Wave controller
- Press and release the Z-Wave button quickly several times once you put the controller in the inclusion mode to ensure the command has gone through
- Put your controller in the EXCLUSION mode and press and release the Z-Wave button, then try adding it to your network again
Initialization/Inclusion Issues
If the unit does not initialize on initial inclusion (i.e., appears to be an unknown device), ask openHAB 2 to reinitialize the device (e.g., in PaperUI, via Configuration > Things > [Name] > Edit) and immediately press the Z-Wave button on the unit (e.g., right after saving your changes in PaperUI).
- Bring the 4-in-1 sensor as close to your Z-Wave gateway controller as possible
- Put your Z-Wave controller in exclusion mode
- Press and release the Z-Wave button TWICE quickly
- The device should disappear from your controller’s device list.
The led indicator will flash 3 times when you take the batteries out and put them back in to indicate the device has been successfully excluded. Please repeat the process following all steps carefully if the led indicator blinks only once when you re-insert the batteries
The ZSE40 v2 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
Use the Wake Up command to set wake-up interval for the sensor (from 10 minutes to 1 week) to report back to the controller. You can also press and release the Z-Wave button once to wake the device up manually.
The following table summarises the channels available for the ZSE40 v2 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Sensor (relative humidity) | sensor_relhumidity | sensor_relhumidity | Humidity | Number |
| Sensor (luminance) | sensor_luminance | sensor_luminance | Number | |
| Sensor (temperature) | sensor_temperature | sensor_temperature | Temperature | Number:Temperature |
| Alarm (motion) | alarm_motion | alarm_motion | Motion | Switch |
| Alarm (tamper) | alarm_tamper | alarm_tamper | Switch | |
| Alarm (burglar) | alarm_burglar | alarm_burglar | Door | Switch |
| Battery Level | battery-level | system.battery_level | Battery | Number |
Indicates the current relative humidity.
The sensor_relhumidity channel is of type sensor_relhumidity and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
Indicates the current light reading.
The sensor_luminance channel is of type sensor_luminance and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Indicates the current temperature.
The sensor_temperature channel is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Indicates if a motion alarm is triggered.
The alarm_motion channel is of type alarm_motion and supports the Switch item and is in the Motion category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Indicates if the tamper alarm is triggered.
The alarm_tamper channel is of type alarm_tamper and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Indicates if the burglar alarm is triggered.
The alarm_burglar channel is of type alarm_burglar and supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The system.battery-level channel is of type system.battery-level and supports the Number item and is in the Battery category.
This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%.
The following table provides a summary of the 7 configuration parameters available in the ZSE40 v2. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Temperature Scale | Set the temperature scale |
| 2 | Temperature Sensitivity | Amount the temperature must change before a report is sent |
| 3 | Humidity | Configure Relative Humidity |
| 4 | Light Sensor | Configure Light Sensor |
| 5 | Trigger Interval | Set the trigger interval for motion sensor re-activation. |
| 6 | Motion Sensor Sensitivity | Adjust sensitivity of the motion sensor. |
| 7 | LED indicator mode | Select the LED indicator mode |
| Wakeup Interval | Sets the interval at which the device will accept commands from the controller | |
| Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |
Set the temperature scale
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Celsius |
| 1 | Fahrenheit |
The manufacturer defined default value is 0 (Celsius).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Amount the temperature must change before a report is sent Use this setting to set a range for how much the temperature needs to change for it to be reported by the sensor
Values: 1 - 50. Values are in 1/10 of a degree C, so 1 is 0.1 degree and 50 is 5 degrees.
Default: 10 (1 degree). The sensor will report the new temperature value to the controller whenever the temperature goes up or down by 1 degree. Values in the range 1 to 50 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Configure Relative Humidity Use it to set humidity percentage change to be reported by the sensor. Values: 1 - 50 where 1 stands for 1% and 50 stands for 50%. Default set to 10%. Values in the range 1 to 50 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Configure Light Sensor Reports light level in percentage (1-100). Use it to choose light percentage change to be reported by the sensor. Values: 5 - 50 where 5 stands for 5% and 50 stands for 50%. Default set to 10%. Values in the range 1 to 50 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Set the trigger interval for motion sensor re-activation. Use it to set trigger interval - the time when motion is reported again after initial trigger. Values: 15 - 255 where 1 stands for 1 second and 255 stands for 255 seconds. Default set to 15 seconds. NOTE: Small interval will increase activity and decrease battery life. Values in the range 15 to 255 may be set.
The manufacturer defined default value is 15.
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Adjust sensitivity of the motion sensor.
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | highest |
| 2 | higher |
| 3 | high |
| 4 | normal |
| 5 | low |
| 6 | lower |
| 7 | lowest |
The manufacturer defined default value is 3 (high).
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Select the LED indicator mode LED indicator will flash every 3 minutes or whenever you press the Z-Wave button to indicate temperature level.
Green = under 60°F
Blue = 60°-75°F
Yellow = 75°-83°F
Purple = 83°-97°F
Red = over 97°F / motion detected / tamper switch triggered
NOTE: Mode 2 will increase activity and decrease battery life The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | Off |
| 2 | Pulsing Temperature, Flashing Motion |
| 3 | Flashing Temperature and Motion |
| 4 | No Temperature, Flashing Motion |
The manufacturer defined default value is 4 (No Temperature, Flashing Motion).
This parameter has the configuration ID config_7_1 and is of type INTEGER.
The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.
This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.
Note that this setting does not affect the devices ability to send sensor data, or notification events.
This parameter has the configuration ID wakeup_interval and is of type INTEGER.
When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.
This parameter has the configuration ID wakeup_node and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZSE40 v2 supports 1 association group.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Receive sensor updates
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V7 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V4 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_WAKE_UP_V2 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.