| layout | title |
|---|---|
documentation |
ITEMP - ZWave |
{% include base.html %}
This describes the Z-Wave device ITEMP, manufactured by Wintop with the thing type UID of wintop_itemp_00_000.
The device is in the category of Sensor, defining Device used to measure something.
The ITEMP supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The ITEMP does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
Binary & Temperature sensor
Remove the cover and press the tamper switch for 3 seconds until the red LED blinks.
Remove the cover and press the tamper switch for 3 seconds until the red LED blinks.
The ITEMP does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
Remove the cover and press the tamper switch for 3 seconds until the red LED blinks.
The following table summarises the channels available for the ITEMP -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Binary Sensor | sensor_binary | sensor_binary | Switch | |
| Sensor (temperature) | sensor_temperature | sensor_temperature | Temperature | Number:Temperature |
| Alarm (CO2) | alarm_co2 | alarm_co2 | CarbonDioxide | Switch |
| Battery Level | battery-level | system.battery_level | Battery | Number |
Indicates if a sensor has triggered.
The sensor_binary channel is of type sensor_binary and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Triggered |
| OFF | Untriggered |
Indicates the current temperature.
The sensor_temperature channel is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Indicates if the carbon dioxide alarm is triggered.
The alarm_co2 channel is of type alarm_co2 and supports the Switch item and is in the CarbonDioxide category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The system.battery-level channel is of type system.battery-level and supports the Number item and is in the Battery category.
This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%.
The following table provides a summary of the 4 configuration parameters available in the ITEMP. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Reset to factory default | Delete configuration but keeps inclusion |
| 2 | Command sent on external dry contact | Configure what te external contact sends when trigger |
| 5 | Operating Mode | Operating Mode |
| 6 | Temperature Offset | Temperature Offset |
| Wakeup Interval | Sets the interval at which the device will accept commands from the controller | |
| Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |
Delete configuration but keeps inclusion
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No (default) |
| 1 | Execute reset |
The manufacturer defined default value is 0 (No (default)).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Configure what te external contact sends when trigger
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Alarm Resport Type 2 (default) |
| 1 | Basic On or Basic Off |
The manufacturer defined default value is 0 (Alarm Resport Type 2 (default)).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Operating Mode Defines if the sensor is in normal wakeup mode or always on (drains battery fast) The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | Normal Wakeup (default) |
| 3 | Always awake |
The manufacturer defined default value is 1 (Normal Wakeup (default)).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Temperature Offset Can be used to calibrate the temperature sensors function. Calibrated as factory default. Values in the range 0 to 15300 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_6_2 and is of type INTEGER.
The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.
This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.
Note that this setting does not affect the devices ability to send sensor data, or notification events.
This parameter has the configuration ID wakeup_interval and is of type INTEGER.
When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.
This parameter has the configuration ID wakeup_node and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ITEMP supports 2 association groups.
Association group 1 supports 5 nodes.
Association group 2 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_WAKE_UP_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.