| layout | title |
|---|---|
documentation |
NAS-WR01ZE - ZWave |
{% include base.html %}
This describes the Z-Wave device NAS-WR01ZE, manufactured by Shenzhen Neo Electronics Co., Ltd with the thing type UID of shenzhen_coolcampwrplug_00_000.
The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.
The NAS-WR01ZE supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
This Plug provides line voltage, current load, power consumption and energy consumption measuring.
- Voltage – The Supply Power Voltage For Plug.
- Current – The Current for the Electric Device Connect to Plug Consumption.
- Power – Power Consumed by an Electric Device in an instant, unit: Watt (W).
- Energy – Energy Consumed by an Electric Device through a Time Period. Most commonly measured in Kilowatt-hours (kWh). One kilowatt-hour is Equal to One Kilowatt of Power Consumed over a Period of One Hour, 1kWh = 1000Wh.0Wh.
- Make sure the sensor is powered.
- Set Z‐Wave controller or Z‐Wave gateway into inclusion mode (Refer to the controller or gateway operating manual)
- Press the button three times within 1.5 second, the device will enter inclusion mode. And the LED will flash on and off with green alternately five times within 2 seconds.
- Make sure the sensor is powered.
- Set Z‐Wave controller or Z‐Wave gateway into exclusion mode (Refer to the controller or gateway operating manual)
- Press the button three times within 1.5 second, the device will enter exclusion mode. And the LED will flash on and off with yellow alternately five times within 2 seconds.
The following table summarises the channels available for the NAS-WR01ZE -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
| Electric meter (amps) | meter_current | meter_current | Energy | Number |
| Electric meter (volts) | meter_voltage | meter_voltage | Energy | Number |
| Clear Accumulated Energy | meter_reset | meter_reset | Energy | Switch |
| Alarm (power) | alarm_power | alarm_power | Energy | Switch |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous current consumption.
The meter_current channel is of type meter_current and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous voltage.
The meter_voltage channel is of type meter_voltage and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Reset the meter.
The meter_reset channel is of type meter_reset and supports the Switch item and is in the Energy category.
Indicates if a power alarm is triggered.
The alarm_power channel is of type alarm_power and supports the Switch item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
The following table provides a summary of the 11 configuration parameters available in the NAS-WR01ZE. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Relay On/Off State Saved Disable | Relay On/Off State Saved Disable |
| 2 | Button Switch Function Disable | Button Switch Function Disable |
| 3 | LED indication Disable | LED indication Disable |
| 4 | Timer Enable | Timer Enable |
| 5 | Timing Length Setting | Timing Length Setting |
| 6 | Meter reporting function | Meter reporting function |
| 7 | Interval of meter reporting setting | Interval of meter reporting setting |
| 8 | Maximum output current setting | Maximum output current setting |
| 9 | Current Differential Setting | Current Differential Setting |
| 10 | Current Alarm Value | Current Alarm Value |
| 11 | Clear Accumulated Energy | Clear accumulated energy |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Relay On/Off State Saved Disable
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Do not save Relay State |
| 1 | Save Relay State |
The manufacturer defined default value is 1 (Save Relay State).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Button Switch Function Disable
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Button disabled |
| 1 | Button enabled |
The manufacturer defined default value is 1 (Button enabled).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
LED indication Disable
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable LED |
| 1 | Enable LED |
The manufacturer defined default value is 1 (Enable LED).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Timer Enable
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Timer Disable |
| 1 | Timer Enable |
The manufacturer defined default value is 0 (Timer Disable).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Timing Length Setting
Values in the range 0 to 32767 may be set.
The manufacturer defined default value is 120.
This parameter has the configuration ID config_5_2 and is of type INTEGER.
Meter reporting function
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable Meter Report |
| 1 | Enable Meter Report |
The manufacturer defined default value is 1 (Enable Meter Report).
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Interval of meter reporting setting
Values in the range 30 to 32767 may be set.
The manufacturer defined default value is 300.
This parameter has the configuration ID config_7_2 and is of type INTEGER.
Maximum output current setting The Value must be greather than the alarm value defined in Parameter 10 Values in the range 1 to 16 may be set.
The manufacturer defined default value is 16.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Current Differential Setting
Values in the range 1 to 1600 may be set.
The manufacturer defined default value is 50.
This parameter has the configuration ID config_9_2 and is of type INTEGER.
Current Alarm Value The Value must be less than the max. output value defined in Parameter 8 Values in the range 1 to 15 may be set.
The manufacturer defined default value is 13.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Clear accumulated energy
If this parameter is set to '0' or default, the accumulated energy saved in the plug will be cleared by '0'.
Other values will not change current accumulated energy value.
This parameter value cannot be saved in NVR mounted in the plug. The accumulated energy consumed will not be changed when the plug is added or removed from the Z-Wave network, but this value will be cleared after resetting the plug to factory default settings.
Note: Users can also send METER_RESET (Meter Command Class) command to clear accumulated energy. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Save accumulated energy |
| 1 | Clear Accumulated Energy |
The manufacturer defined default value is 0 (Save accumulated energy).
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The NAS-WR01ZE supports 3 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Assigned to Plugs status - On/Off. Allows for receiving control command from trigger devices whenever the Plug is turned On or Off.
- NOTIFICATION_REPORT_V4
- METER_REPORT_V4
- SWITCH_BINARY_REPORT
- DEVICE_RESET_LOCALLY_NOTIFICATION
Association group 1 supports 1 node.
Sending control commands to associated devices. If current load is over the max current defined in parameter #3, the Plug will send a BASIC_SET (0xFF) to associated devices. When current load is normal, plug will send a BASIC_SET (0x00). BASIC_SET
Association group 2 supports 5 nodes.
Send Notification to associated devices. NOTIFICATION_REPORT_V4
Association group 3 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V8 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.