| layout | title |
|---|---|
documentation |
ZMNKAD - ZWave |
{% include base.html %}
This describes the Z-Wave device ZMNKAD, manufactured by Goap with the thing type UID of qubino_luxyswitch_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The ZMNKAD supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
The Qubino LUXY Smart Switch is ideal for gentle illumination of any room, for visual and sound notifications, and for controlling various loads, using the built-in relay.
Manual inclusion is triggered by the following procedure:
- Full white needs to be active (c-button 2). The user can select it by quickly pressing the c-button2 once.
- When full white is enabled, press c-button3 and hold it for 5 seconds (while white is glowing, hold c-button3 for 5 seconds).
- After 5 seconds, the device starts flashing, with the following pattern: green 1 second on, 0.5 second off.
- Once the device receives a nodeId or after 10 seconds, it stops flashing and turns green.
Exclusion is triggered by the following procedure:
- Full white needs to be active (c-button 2).
- When full white is enabled, press c-button3 and hold it for 5 seconds (while white is glowing hold c-button3 for 5 seconds).
- After 5 seconds, the device starts flashing with the following pattern: red 1 second on, 0.5 second off.
- Once the device loses its nodeId or after 10 seconds, it stops flashing and turns red.
The following table summarises the channels available for the ZMNKAD -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Color Control | color_color | color_color | ColorLight | Color |
| Color Temperature | color_temperature | color_temperature | ColorLight | Dimmer |
| Alarm (power) | alarm_power | alarm_power | Energy | Switch |
| Alarm (SIREN) 0 | notification_siren | notification_siren | Switch | |
| Switch 1 | switch_binary1 | switch_binary | Switch | Switch |
| Dimmer 1 | switch_dimmer1 | switch_dimmer | DimmableLight | Dimmer |
| Electric meter (watts) 1 | meter_watts1 | meter_watts | Energy | Number |
| Electric meter (kWh) 1 | meter_kwh1 | meter_kwh | Energy | Number |
| Color Control 1 | color_color1 | color_color | ColorLight | Color |
| Color Temperature 1 | color_temperature1 | color_temperature | ColorLight | Dimmer |
| Alarm (SIREN) 1 | notification_siren1 | notification_siren | Switch | |
| Switch 2 | switch_binary2 | switch_binary | Switch | Switch |
| Electric meter (watts) 2 | meter_watts2 | meter_watts | Energy | Number |
| Electric meter (kWh) 2 | meter_kwh2 | meter_kwh | Energy | Number |
| Alarm (power) 2 | alarm_power2 | alarm_power | Energy | Switch |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The color channel allows to control the color of a light. It is also possible to dim values and switch the light on and off.
The color_color channel is of type color_color and supports the Color item and is in the ColorLight category.
The color temperature channel allows to set the color temperature of a light from 0 (cold) to 100 (warm).
The color_temperature channel is of type color_temperature and supports the Dimmer item and is in the ColorLight category.
Indicates if a power alarm is triggered.
The alarm_power channel is of type alarm_power and supports the Switch item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Indicates the siren notification has been triggered.
The notification_siren channel is of type notification_siren and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
Switch the power on and off.
The switch_binary1 channel is of type switch_binary and supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer1 channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Indicates the instantaneous power consumption.
The meter_watts1 channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh1 channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The color channel allows to control the color of a light. It is also possible to dim values and switch the light on and off.
The color_color1 channel is of type color_color and supports the Color item and is in the ColorLight category.
The color temperature channel allows to set the color temperature of a light from 0 (cold) to 100 (warm).
The color_temperature1 channel is of type color_temperature and supports the Dimmer item and is in the ColorLight category.
Indicates the siren notification has been triggered.
The notification_siren1 channel is of type notification_siren and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
Switch the power on and off.
The switch_binary2 channel is of type switch_binary and supports the Switch item and is in the Switch category.
Indicates the instantaneous power consumption.
The meter_watts2 channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh2 channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates if a power alarm is triggered.
The alarm_power2 channel is of type alarm_power and supports the Switch item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
The following table provides a summary of the 11 configuration parameters available in the ZMNKAD. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Relay contact type | Relay contact type |
| 3 | Turning off alarming | Turning off alarming |
| 10 | Auto On timer | Auto On timer |
| 11 | Auto Off timer | Auto Off timer |
| 12 | Auto On timer relay | Auto On timer relay |
| 13 | Auto Off timer relay | Auto Off timer relay |
| 30 | Restore state on power failure | Restore state on power failure |
| 31 | Restore relay state on power failure | Restore relay state on power failure |
| 40 | Power Consumption Reporting Threshold | Power Consumption Reporting Threshold |
| 42 | Power Consumption Threshold (time) | Power Consumption Threshold (time) |
| 70 | Overload safety switch | Overload safety switch |
Relay contact type
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | NO |
| 1 | NC |
The manufacturer defined default value is 0 (NO ).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Turning off alarming Default value 1
0 – only by z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, sound switch play tone, sound switch configuration, switch color set, switch color start/stop level change, notification report idle)
1 – capacitive input or z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, sound switch play tone, sound switch configuration, switch color set, switch color start/stop level change, notification report idle) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Only by Z-Wave |
| 1 | Capacitive input or by Z-wave |
The manufacturer defined default value is 1 (Capacitive input or by Z-wave).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Auto On timer Defines the time after which the device is turned to last known state.
Default value 0
0 – disabled
30 – 32535 = 30 – 32535 seconds after which the device turns on Values in the range 0 to 32535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_10_2 and is of type INTEGER.
Auto Off timer Defines the time after which the device is turned off.
Default value 0
0 – disabled
30 – 32535 = 30 – 32535 seconds after which the device turns off Values in the range 0 to 32535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_11_2 and is of type INTEGER.
Auto On timer relay Defines the time after which the device's relay is turned to last known state.
Default value 0
0 – disabled
30 – 32535 = 30 – 32535 seconds after which the device turns on Values in the range 0 to 32535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_12_2 and is of type INTEGER.
Auto Off timer relay Defines the time after which the device's relay is turned off.
Default value 0
0 – disabled
30 – 32535 = 30 – 32535 seconds after which the device turns off Values in the range 0 to 32535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_13_2 and is of type INTEGER.
Restore state on power failure Default value 1
1 – enabled (the device will restore state on power failure)
0 – dissabled (the device will not restore state on power failure and will remain off) Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_30_1 and is of type INTEGER.
Restore relay state on power failure Default value 1
1 – enabled (the device will restore state on power failure)
0 – disabled (the device will not restore state on power failure and will remain off) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 1 (Enabled).
This parameter has the configuration ID config_31_1 and is of type INTEGER.
Power Consumption Reporting Threshold Choose by how much power consumption needs to increase or decrease to be reported. Values correspond to percentages so if 10 is set (by default), the device will report any power consumption changes of 10% or more compared to the last reading.
Values (size is 1 byte dec):
default value 10
0 - Power consumption reporting disabled
1 - 100 = 1% - 100% Power consumption reporting enabled. New value is reported only when Wattage in real time changes by more than the percentage value set in this parameter compared to the previous Wattage reading, starting at 1% (the lowest value possible).
NOTE: Power consumption needs to increase or decrease by at least 1 Watt to be reported, REGARDLESS of percentage set in this parameter. Values in the range 0 to 100 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_40_1 and is of type INTEGER.
Power Consumption Threshold (time) Set value refers to the time interval with which power consumption in Watts is reported (0 – 32535 seconds). If 300 is entered (by default), energy consumption reports will be sent to the gateway (hub) every 300 seconds (or 5 minutes).
default value 0
0 - Power consumption reporting disabled
30 - 32535 = 30 - 32535 seconds. Power consumption reporting enabled. Report is sent according to time interval (value) set here. Values in the range 0 to 32535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_42_2 and is of type INTEGER.
Overload safety switch The function allows for turning off the controlled device in case of exceeding the defined power for more than 5s. Controlled device can be turned back on by input I1 or sending a control frame.
Values (size is 2 byte dec):
default value 2300
1 – 2300 = 1 W – 2300W
0 = function not active
ⓘ NOTE: This functionality is not an overload safety protection, please check the technical specifications chapter for more details.
In case of overload the following message will be send towards the controller:
COMMAND_CLASS_NOTIFICATION_V5
The Alarm V1 type field set to 0x00
Notification Type 0x08 and 0x08 (Overload detected) Values in the range 0 to 2300 may be set.
The manufacturer defined default value is 2300.
This parameter has the configuration ID config_70_2 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZMNKAD supports 5 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Root endpoint Command Class/Command
COMMAND_CLASS_DEVICE_RESET_LOCALLY, DEVICE_RESET_LOCALLY_NOTIFICATION, COMMAND_CLASS_SWITCH_MULTILEVEL_V4, SWITCH_MULTILEVEL_REPORT_V4, COMMAND_CLASS_SWITCH_COLOR_V3, SWITCH_COLOR_REPORT_V3, COMMAND_CLASS_NOTIFICATION_V8, NOTIFICATION_REPORT_V8, COMMAND_CLASS_SWITCH_BINARY, SWITCH_BINARY_REPORT, COMMAND_CLASS_METER, METER_REPORT
Association group 1 supports 1 node.
Root endpoint Command Class/Command
COMMAND_CLASS_BASIC_V2, BASIC_SET_V2
Association group 2 supports 5 nodes.
Root endpoint Command Class/Command
COMMAND_CLASS_SWITCH_MULTILEVEL_V4, SWITCH_MULTILEVEL_SET_V4
Association group 3 supports 5 nodes.
Root endpoint Command Class/Command
COMMAND_CLASS_SWITCH_COLOR_V3, SWITCH_COLOR_SET_V3
Association group 4 supports 5 nodes.
Root endpoint Command Class/Command
COMMAND_CLASS_SWITCH_MULTILEVEL_V4, SWITCH_MULTILEVEL_SET_V4
Association group 5 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | Linked to BASIC |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_SWITCH_COLOR_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V8 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_SECURITY_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | Linked to BASIC |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_SWITCH_COLOR_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ALARM_V8 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_SECURITY_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ALARM_V8 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.