| layout | title |
|---|---|
documentation |
PAT02-B - ZWave |
{% include base.html %}
This describes the Z-Wave device PAT02-B, manufactured by Philio Technology Corp with the thing type UID of philio_pat02b_00_000.
The device is in the category of Sensor, defining Device used to measure something.
The PAT02-B supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The PAT02-B does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
The flood multisensor PAT02 has flood, temperature and humidity, 3 sensors function in one, based on Z-WaveTM technology
Pressing the tamper key three times within 1.5 seconds to enter the inclusion mode.
Pressing tamper key three times within 1.5 seconds to enter the exclusion mode
The PAT02-B does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
Press the tamper key once. The device will wake-up 10 seconds.
The following table summarises the channels available for the PAT02-B -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Binary Sensor | sensor_binary | sensor_binary | Switch | |
| Sensor (temperature) | sensor_temperature | sensor_temperature | Temperature | Number:Temperature |
| Sensor (relative humidity) | sensor_relhumidity | sensor_relhumidity | Humidity | Number |
| Alarm (burglar) | alarm_burglar | alarm_burglar | Door | Switch |
| Battery Level | battery-level | system.battery_level | Battery | Number |
Indicates if a sensor has triggered.
The sensor_binary channel is of type sensor_binary and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Triggered |
| OFF | Untriggered |
Indicates the current temperature.
The sensor_temperature channel is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Indicates the current relative humidity.
The sensor_relhumidity channel is of type sensor_relhumidity and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
Indicates if the burglar alarm is triggered.
The alarm_burglar channel is of type alarm_burglar and supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The system.battery-level channel is of type system.battery-level and supports the Number item and is in the Battery category.
This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%.
The following table provides a summary of the 8 configuration parameters available in the PAT02-B. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 5 | Operation Mode | set Operation Mode using bit to control |
| 7 | Customer Function | Customer Function switch using bit control |
| 10 | Auto Report Battery Time | The interval time for auto reporting the battery level. |
| 13 | Auto Report Temperature Time | The interval time for auto reporting the temperature state. |
| 14 | Auto Report Humidity Time | The interval time for auto reporting the humidity state. |
| 20 | Auto Report Tick Interval | The interval time for auto report each tick. |
| 21 | Temperature Differential Report | The temperature differential to report. |
| 23 | Humidity Differential Report | The humidity differential to report. |
| Wakeup Interval | Sets the interval at which the device will accept commands from the controller | |
| Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |
set Operation Mode using bit to control set Operation Mode using bit to control
- Bit 0: Reserve
- Bit 1: Reserve
- Bit 2: Reserve
- Bit 3: Setting temperature scale
- 0: Fahrenheit
- 1: Celsius
- Bit 4: Reserve
- Bit 5: Reserve
- Bit 6: Reserve
- Bit 7: Reserve Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Customer Function switch using bit control Customer Function switch using bit control
- Bit 0: Reserve
- Bit 1: Reserve
- Bit 2: Reserve
- Bit 3: not applicable for this device variant, set to 0
- Bit 4: Notification Type
- 0: Using Notification Report
- 1: Using Sensor Binary Report
- Bit 5: Disable Multi CC in auto report
- 0: Enable
- 1: Disable
- Bit 6: not applicable for this device variant, set to 0
- Bit 7: Reserve Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
The interval time for auto reporting the battery level. The interval time for auto reporting the battery level.
- 0 = Turn off auto report battery.
- 1-127 = Number of ticks. The default value is 12. The tick time can be set by configuration No. 20. Values in the range 1 to 127 may be set.
The manufacturer defined default value is 12.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
The interval time for auto reporting the temperature state. The interval time for auto reporting the temperature state.
- 0 = Turn off auto report temperature.
- 1-127 = Number of ticks. The default value is 12. The tick time can be set by configuration No. 20. Values in the range 1 to 127 may be set.
The manufacturer defined default value is 12.
This parameter has the configuration ID config_13_1 and is of type INTEGER.
The interval time for auto reporting the humidity state. The interval time for auto reporting the humidity state.
- 0 = Turn off auto report.
- 1-127 = Number of ticks. The default value is 12. The tick time can be set by configuration No. 20. Values in the range 0 to 127 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_14_1 and is of type INTEGER.
The interval time for auto report each tick. The interval time for auto report each tick. Units of one minute. Setting configuration will affect configuration no. 10, 13, 14 and 15.
- Caution1: Setting to 0 means turn off all auto report function.
- Caution2: The value is unsigned byte. Values in the range 0 to 255 may be set.
The manufacturer defined default value is 30.
This parameter has the configuration ID config_20_1 and is of type INTEGER.
The temperature differential to report. The temperature differential to report.
- The unit is Fahrenheit.
- Enable this function the device will detect every 10 seconds. Values in the range 0 to 127 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_21_1 and is of type INTEGER.
The humidity differential to report. The humidity differential to report.
- The unit is percentage.
- Enable this function the device will detect every 10 seconds. Values in the range 0 to 60 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_23_1 and is of type INTEGER.
The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.
This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.
Note that this setting does not affect the devices ability to send sensor data, or notification events.
This parameter has the configuration ID wakeup_interval and is of type INTEGER.
When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.
This parameter has the configuration ID wakeup_node and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The PAT02-B supports 2 association groups.
Association group 1 supports 7 nodes.
Association group 2 supports 7 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V2 | Linked to BASIC |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V4 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_WAKE_UP_V2 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CMD_V1 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.