| layout | title |
|---|---|
documentation |
509519 - ZWave |
{% include base.html %}
This describes the Z-Wave device 509519, manufactured by Merten with the thing type UID of merten_509519_00_000.
The device is in the category of Motion Detector, defining Motion sensors/detectors.
The 509519 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Movement/presence detectors switch on as soon as they detect a moving heat source. This can be a person, but also animals, trees, cars or differences in temperature in windows. In order to avoid false alarms, the chosen installation site should be such that undesired heat sources cannot be detected (see section „Selecting the installation site“).
Turn the controller A on the ARGUS to position B: The learning mode is activated.
Turn the controller A on the ARGUS to position B: The learning mode is activated.
The following table summarises the channels available for the 509519 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Switch 1 | switch_binary1 | switch_binary | Switch | Switch |
| Switch 2 | switch_binary2 | switch_binary | Switch | Switch |
| Binary Sensor 3 | sensor_binary3 | sensor_binary | Switch | |
| Sensor (general) 3 | sensor_general3 | sensor_general | Number | |
| Binary Sensor 4 | sensor_binary4 | sensor_binary | Switch | |
| Sensor (luminance) 4 | sensor_luminance4 | sensor_luminance | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary1 channel is of type switch_binary and supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary2 channel is of type switch_binary and supports the Switch item and is in the Switch category.
Indicates if a sensor has triggered.
The sensor_binary3 channel is of type sensor_binary and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Triggered |
| OFF | Untriggered |
The sensor_general3 channel is of type sensor_general and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Indicates if a sensor has triggered.
The sensor_binary4 channel is of type sensor_binary and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Triggered |
| OFF | Untriggered |
Indicates the current light reading.
The sensor_luminance4 channel is of type sensor_luminance and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
The device has no configuration parameters defined.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The 509519 supports 2 association groups.
Master
Association group 1 supports 4 nodes.
Report
Association group 2 supports 4 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_PROTECTION_V2 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_PROTECTION_V2 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_VERSION_V1 | |
| COMMAND_CLASS_SENSOR_CONFIGURATION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_VERSION_V1 | |
| COMMAND_CLASS_SENSOR_CONFIGURATION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.