| layout | title |
|---|---|
documentation |
MH-DT311 - ZWave |
{% include base.html %}
This describes the Z-Wave device MH-DT311, manufactured by McoHome Technology Co., Ltd with the thing type UID of mcohome_mhdt311_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The MH-DT311 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Dimmer Switch is a wall panel built-in with Z-Wave Plus module. With its stylish design and stable performance, the panel can be used to control the light level. It supports basic command class， multi channel command class and multi channel association command class, also works as a repeater in a Z-Wave network. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturers.
Set controller into Add/Remove mode, and press 3 clicks on "+" or "-" button to add/remove. If succeed, green LED flicks 4 times.
Set controller into Add/Remove mode, and press 3 clicks on "+" or "-" button to add/remove. If succeed, green LED flicks 4 times.
The following table summarises the channels available for the MH-DT311 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Binary | switch_binary | switch_binary | Switch | Switch |
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | scene_number | Number | |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Electric meter (volts) | meter_voltage | meter_voltage | Energy | Number |
| Electric meter (amps) | meter_current | meter_current | Energy | Number |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
| Alarm (power) | alarm_power | alarm_power | Energy | Switch |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous voltage.
The meter_voltage channel is of type meter_voltage and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous current consumption.
The meter_current channel is of type meter_current and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates if a power alarm is triggered.
The alarm_power channel is of type alarm_power and supports the Switch item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
The following table provides a summary of the 19 configuration parameters available in the MH-DT311. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Dimmer state saved or not when power down | Dimmer state saved or not when power down |
| 2 | Dimming mode | Dimming mode |
| 3 | Auto detection of dimming mode when powered on | Auto detection of dimming mode when powered on |
| 4 | LED Backlit brightness level | LED Backlit brightness level |
| 5 | Minimum brightness level | |
| 6 | Maximum brightness level | |
| 7 | Single dimming step time (Manual) | Single dimming step time (Manual) |
| 8 | Single dimming step size (Manual) | Single dimming step size (Manual) |
| 9 | Single dimming step time (Auto) | Single dimming step time (Auto) |
| 10 | Single dimming step size (Auto) | Single dimming step size (Auto) |
| 11 | The dimming percentage single touch | The dimming percentage single touch |
| 12 | Reporting interval for dimming level | Reporting interval for dimming level |
| 13 | External switch type | External switch type |
| 14 | External switch input | External switch input |
| 15 | Energy meter reporting | Energy meter reporting |
| 16 | Energy meter reporting interval | Energy meter reporting interval |
| 17 | Beep | Beep |
| 32 | Ampere alarm threshold | Ampere alarm threshold |
| 33 | Voltage alarm threshold | Voltage alarm threshold |
Dimmer state saved or not when power down 0 - Dimmer will be off when powered again
1 - Dimmer will keep the same state when powered again Values in the range 0 to 1 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Dimming mode 0 - leading edge
1 - trailing edge
2 - On/off only Values in the range 0 to 2 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Auto detection of dimming mode when powered on 0 - Auto detection disabled
1 - Auto detection enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
LED Backlit brightness level 0 - LED disabled
1-10 Min level-Max level Values in the range 0 to 10 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Values in the range 1 to 98 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Values in the range 2 to 99 may be set.
The manufacturer defined default value is 63.
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Single dimming step time (Manual)
Values in the range 0 to 2550 may be set.
The manufacturer defined default value is 30.
This parameter has the configuration ID config_7_2 and is of type INTEGER.
Single dimming step size (Manual)
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Single dimming step time (Auto)
Values in the range 0 to 2550 may be set.
The manufacturer defined default value is 30.
This parameter has the configuration ID config_9_2 and is of type INTEGER.
Single dimming step size (Auto)
Values in the range 0 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
The dimming percentage single touch
Values in the range 0 to 99 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Reporting interval for dimming level
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
External switch type
Values in the range 0 to 1 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_13_1 and is of type INTEGER.
External switch input
Values in the range 0 to 4 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_14_1 and is of type INTEGER.
Energy meter reporting
Values in the range 0 to 15 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_15_1 and is of type INTEGER.
Energy meter reporting interval
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 16.
This parameter has the configuration ID config_16_1 and is of type INTEGER.
Beep
Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_17_1 and is of type INTEGER.
Ampere alarm threshold
Values in the range 0 to 20480 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_32_2 and is of type INTEGER.
Voltage alarm threshold
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_33_2 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The MH-DT311 supports 4 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 1 node.
Association group 2 supports 5 nodes.
Association group 5 supports 5 nodes.
Association group 8 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V4 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.