| layout | title |
|---|---|
documentation |
ZW4106 / GE39342 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZW4106 / GE39342, manufactured by Honeywell with the thing type UID of honeywell_39342_00_000.
The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.
The ZW4106 / GE39342 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
- 2 Simultaneously Controlled Outlets
- Only Blocks One Outlet / Cords Exit Sideways
- Indoor
- Wall Plug
- 120 VAC, 60 Hz
- 908.42/916 MHz
- Max Incandescent Load 600W (5A)
- Max Resistive Load 1800W (15A)
- Max Motor 1/2 HP
- Max Range 45 m
- Operating Temperature Range 0°C to 40°C
- UL Listed
- FCC ID U2ZZW4104
- IC 6924A-ZW4104
Press and release the manual/program button. (Tested to work with Network Wide Inclusion.)
Press and release the manual/program button.
Appears to be the same device as the GE 14282 / Jasco ZW4106.
The following table summarises the channels available for the ZW4106 / GE39342 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
The following table provides a summary of the 1 configuration parameters available in the ZW4106 / GE39342. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | LED Light Control | Controls LED light state |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Controls LED light state
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED Light on when switch turned OFF (Default) |
| 1 | LED Light on when switch turned On |
| 2 | LED Light Always Off |
The manufacturer defined default value is 0 (LED Light on when switch turned OFF (Default)).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZW4106 / GE39342 supports 3 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
Basic Set controlled with local load
Association group 2 supports 5 nodes.
Basic Set controlled by double pressing button
Association group 3 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.