| layout | title |
|---|---|
documentation |
GE 46202 - ZWave |
{% include base.html %}
This describes the Z-Wave device GE 46202, manufactured by Jasco Products with the thing type UID of ge_46202_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The GE 46202 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Home automation is even smarter with the GE Enbrighten Z-Wave Plus In-Wall Smart Switch with QuickFit™ and SimpleWire™. When paired with a compatible hub, the hardwired smart switch operates wall, ceiling and accent lighting through individual commands and programmed settings. Wirelessly control and schedule indoor or outdoor fixtures for effortless management of your home. Your automation possibilities are seemingly infinite when connected to hubs from Ring, Wink, SmartThings, HomeSeer, Vera, Nexia and more.
- Once the controller is ready to include your device, press up and release on the toggle to include it in the network.
- Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize performance.
Once the controller is ready to exclude your device, press up and release on the toggle to exclude it from the network.
The following table summarises the channels available for the GE 46202 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
This channel provides the scene, and the event as a decimal value in the form <scene>.<event>. The scene number is set by the device, and the event is as follows -:
| Event ID | Event Description |
|---|---|
| 0 | Single key press |
| 1 | Key released |
| 2 | Key held down |
| 3 | Double keypress |
| 4 | Tripple keypress |
| 5 | 4 x keypress |
| 6 | 5 x keypress |
The following table provides a summary of the 3 configuration parameters available in the GE 46202. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | LED Mode | LED Indication Configuration |
| 4 | Invert Switch | Invert Switch |
| 19 | Alternate Exclusion | Set Alternate Exclusion Mode |
LED Indication Configuration Sets mode for LED inside toggle switch The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED ON when switch is OFF |
| 1 | LED ON when switch is ON |
| 2 | LED always OFF |
| 3 | LED Always ON |
The manufacturer defined default value is 2 (LED always OFF).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Invert Switch If the switch is accidentally installed upside down with “On” at the bottom and “Off” at the top, the default On/Off rocker settings can be reversed by changing parameter 4’s value to “1”. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Normal Switch Install |
| 1 | Inverted Switch Install |
The manufacturer defined default value is 0 (Normal Switch Install).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Set Alternate Exclusion Mode
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Press any button on the switch |
| 1 | Alternate Exclusion |
The manufacturer defined default value is 0 (Press any button on the switch).
This parameter has the configuration ID config_19_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The GE 46202 supports 3 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Lifeline
Association group 1 supports 5 nodes.
Basic Set single click
Association group 2 supports 5 nodes.
Association group 3 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_APPLICATION_STATUS_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_CENTRAL_SCENE_V3 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.