| layout | title |
|---|---|
documentation |
46201 - ZWave |
{% include base.html %}
This describes the Z-Wave device 46201, manufactured by Jasco Products with the thing type UID of ge_46201_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The 46201 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Getting to know your new Z-Wave device
- Turn ON/OFF manually or remotely via the Z-Wave controller
- Can be added in multiple groups and scenes
- May be used in single pole installation or with up to four GE-branded Add-on Switches in 3-way or 4-way wiring configurations
- Compatible with all incandescent and CFL/LED bulbs
- Auto line/load detection
- Interchangeable paddle switch — white & light almond paddle in package
- Uses a standard, decorative-size wallplate for single-gang installations (wallplate not included)
- Blue LED indicates switch location in a dark room
- Z-Wave certified for simple pairing and integrated home automation
- Screw terminal installation — requires wiring connections for line (hot), load, neutral and ground. Traveler wire required for 3-way or 4-way installation
- This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class.
Press and release the top or bottom of the wireless smart switch (rocker).
Press and release the top or bottom of the wireless smart switch (rocker).
The following table summarises the channels available for the 46201 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
This channel provides the scene, and the event as a decimal value in the form <scene>.<event>. The scene number is set by the device, and the event is as follows -:
| Event ID | Event Description |
|---|---|
| 0 | Single key press |
| 1 | Key released |
| 2 | Key held down |
| 3 | Double keypress |
| 4 | Tripple keypress |
| 5 | 4 x keypress |
| 6 | 5 x keypress |
The following table provides a summary of the 1 configuration parameters available in the 46201. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | Blue LED Night Light | Blue LED Night Light |
Blue LED Night Light This configuration parameter defines the behavior of the blue LED "night light". The default behavior is "ON_WHEN_OFF" - the LED is on when the switch is set to off. The other two options are "ON_WHEN_ON" - the LED is on when the switch is set to on, and "ALWAYS_OFF" - the LED is always off. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED ON when switch is OFF |
| 1 | LED ON when switch is ON |
| 2 | LED always OFF |
The manufacturer defined default value is 0 (LED ON when switch is OFF).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The 46201 supports 3 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
Association group 2 supports 5 nodes.
Association group 3 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_APPLICATION_STATUS_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_CENTRAL_SCENE_V3 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.