| layout | title |
|---|---|
documentation |
35931 - ZWave |
{% include base.html %}
This describes the Z-Wave device 35931, manufactured by Jasco Products with the thing type UID of ge_35931_00_000.
The device is in the category of Light Bulb, defining Devices that illuminate something, such as bulbs, etc..
The 35931 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Breathe new life into your home’s Z-Wave network when you upgrade to an Enbrighten Smart LED Bulb. This 60-watt equivalent bulb works with all standard light fixtures and lamps, allowing you to update to smart control without compromising the design of your home. No wiring is required — simply replace your existing E26 light bulb with the smart bulb (E26 base, A19 style) and begin enjoying the long life of your new light. This Enbrighten Dimmable LED Bulb has full-range dimmability, saving you energy costs year-round. From the convenience of your smartphone or tablet, turn the lights on and off, dim or brighten your room and set lights according to your schedule. At 750 lumens, this LED bulb consumes only 9 watts of power while burning brightly for up to 25,000 hours. Experience the bright side of life with the Enbrighten Smart LED Bulb.
Once the controller is ready to include your LED Smart Bulb, turn on power to the socket. The Enbrighten LED Smart Bulb will be automatically included into your network within 30 seconds, and the smart bulb will flash 2 times to signify successful inclusion into your network.
Once the controller is ready to exclude your LED Smart Bulb, turn on power to the socket. Tthe smart bulb will flash 2 times to signify successful exclusion from your network.
The following table summarises the channels available for the 35931 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The following table provides a summary of the 3 configuration parameters available in the 35931. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Dim level when light is turned ON | Dim level when light is turned ON |
| 9 | Dimming/Brightening Step Level | Dimming/Brightening Step Level |
| 10 | Dimming/Brightening Step Timing | Dimming/Brightening Step Timing |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Dim level when light is turned ON
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Full brightness |
| 1 | Last brightness setting |
The manufacturer defined default value is 0 (Full brightness).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Dimming/Brightening Step Level You may change the dimming step level when you adjust the brightness by your controller/gateway.
When the value is low, dimming/brightening is gradual.
When the value is high, dimming/brightening is rapid. Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Dimming/Brightening Step Timing You may change the dimming speed quicker or slower.
When the value is low, the step timing is quick.
When the value is high, the step timing is slow. Values in the range 1 to 10 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The 35931 supports 1 association group.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.