| layout | title |
|---|---|
documentation |
FGD211 - ZWave |
{% include base.html %}
This describes the Z-Wave device FGD211, manufactured by Fibargroup with the thing type UID of fibaro_fgd211_00_000.
This version of the device is limited to firmware versions below 1.8
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The FGD211 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Remotely controlled Dimmer designed to operate with or without neutral lead. It may be used as a switch in systems without neutral lead.
As a Dimmer it operates under the following loads:
- conventional incandescent
- Halogen 230V
- low voltage halogen 12V (with electronic transformers)
- dimmable LED
- when used with FGB001 it may operate with any dimmable load up to 500W
The Dimmer enters the mode of inclusion after a quick pressing three times the push-button connected to S1 terminal or push-button B located inside the housing. For bi-stable switch perform 3 position changes.
The Dimmer enters the mode of exclusion after a quick pressing three times the push-button connected to S1 terminal or push-button B located inside the housing. For bi-stable switch perform 3 position changes
The following table summarises the channels available for the FGD211 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The following table provides a summary of the 18 configuration parameters available in the FGD211. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Enable/Disable ALL ON/OFF | Activate/Deactive ALL ON/OFF |
| 6 | Separation of association sending (key 1) | Activate/Deactivate association sending for group 1 - Also see param #16 |
| 7 | Control key #2 behaviour | Key no. 2 is not represented by any physical device |
| 8 | Dimming step at automatic control | |
| 9 | Time of MANUALLY moving between values | Options for changing parameter 1-255 (10ms - 2,5s) |
| 10 | Time of AUTOMATIC moving between values | Time of autom. moving the dimmer between min/max |
| 11 | Dimming step at manual control | Options for changing parameter 1-99 |
| 12 | Maximum dimmer level control | Options for changing parameter 2-99 |
| 13 | Minimum dimmer level control | Options for changing parameter 1-98 |
| 14 | Inputs Button/Switch configuration | Binary inputs type configuration |
| 15 | Parm 15 | Double-click set lighting at 100% |
| 16 | Saving state before power failure | Saving state before power failure |
| 17 | 3-way switch | Function of 3-way switch |
| 18 | Synchronizing light level for associated devices | The dimmer communicate the level to the associated devices. (default value 0) |
| 19 | Change [On-Off] bi-stable keys | Allow user to change [On-Off] bi-stable keys |
| 20 | Control impulse length | Change of control impulse length. |
| 30 | Relay 1: Response to General Alarm | |
| 39 | ALARM FLASHING alarm time | Amount of time (ms) the device keeps on flashing after receipt of Alarm Frame |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Activate/Deactive ALL ON/OFF
The following option values may be configured -:
| Value | Description |
|---|---|
| -1 | ALL ON active / ALL OFF active |
| 0 | ALL ON disabled / ALL OFF disabled |
| 1 | ALL ON disabled / ALL OFF active |
| 2 | ALL ON active / ALL OFF disabled |
The manufacturer defined default value is 255.
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Activate/Deactivate association sending for group 1 - Also see param #16
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Map status to all devices in group 1 |
| 1 | Map OFF status to all devices in group 1 |
| 2 | Map OFF status to all devices in group 1 |
The manufacturer defined default value is 0 (Map status to all devices in group 1).
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Key no. 2 is not represented by any physical device Info: Key no. 2 is not represented by any physical device expect of devices on association list. This functionality prevents of lack of reaction on pressing key no. 2 through polling devices from association list one by one and checking their actual states The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Device status is not checked |
| 1 | Device status is checked |
The manufacturer defined default value is 1 (Device status is checked).
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Options for changing parameter 1-255 (10ms - 2,5s) Time of MANUALLY moving between the extreme dimming values Values in the range 1 to 255 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Time of autom. moving the dimmer between min/max Options for changing parameter 1-255 (10ms - 2,5s) - 0: this value disables the smooth change in light intensity. NOTE: value 0 is required for inductive and capacitive devices unsuitable for dimming (e.g. fluorescent lamps, motors, etc...) Values in the range 0 to 255 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Options for changing parameter 1-99
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Options for changing parameter 2-99
Values in the range 2 to 99 may be set.
The manufacturer defined default value is 2.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Options for changing parameter 1-98
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_13_1 and is of type INTEGER.
Binary inputs type configuration
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Mono-stable input (button) |
| 1 | Bi-stable input (switch) |
The manufacturer defined default value is 0 (Mono-stable input (button)).
This parameter has the configuration ID config_14_1 and is of type INTEGER.
Double-click set lighting at 100%
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable double click |
| 1 | Enable double click |
The manufacturer defined default value is 0 (Disable double click).
This parameter has the configuration ID config_15_1 and is of type INTEGER.
Saving state before power failure
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | State NOT saved at power failure |
| 1 | State saved at power failure |
The manufacturer defined default value is 1 (State saved at power failure).
This parameter has the configuration ID config_16_1 and is of type INTEGER.
Function of 3-way switch The function of 3-way switch provides the option to double key no. 1. The dimmer may control two bi-stable push-buttons or an infinite number of mono-stable push-buttons. (default value 0) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
The manufacturer defined default value is 0 (Disable).
This parameter has the configuration ID config_17_1 and is of type INTEGER.
The dimmer communicate the level to the associated devices. (default value 0)
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
The manufacturer defined default value is 0 (Disable).
This parameter has the configuration ID config_18_1 and is of type INTEGER.
Allow user to change [On-Off] bi-stable keys This function allow user to change [On-Off] bi-stable keys (parameter no. 14) (default value 0) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Device changes status on key status change |
| 1 | Device status depends on key status |
The manufacturer defined default value is 0 (Device changes status on key status change).
This parameter has the configuration ID config_19_1 and is of type INTEGER.
Change of control impulse length. This function will enable decreasing the minimum level of the Dimmer by extending the control impulse.[100 - 170].
By changing the minimem level, the user may completely dim LED bulbs. Not all LED bulbs available on the market have the dimming capabilty. Values in the range 100 to 170 may be set.
The manufacturer defined default value is 110.
This parameter has the configuration ID config_20_1 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | DEACTIVATION - no response to alarm frames |
| 1 | Alarm relay ON |
| 2 | Alarm relay OFF |
| 3 | ALARM FLASHING |
The manufacturer defined default value is 3 (ALARM FLASHING).
This parameter has the configuration ID config_30_1 and is of type INTEGER.
Amount of time (ms) the device keeps on flashing after receipt of Alarm Frame
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_39_2 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The FGD211 supports 3 association groups.
Association group 1 supports 5 nodes.
Association group 2 supports 5 nodes.
Association group 3 supports 1 node.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.