| layout | title |
|---|---|
documentation |
ZW15SM - ZWave |
{% include base.html %}
This describes the Z-Wave device ZW15SM, manufactured by Wenzhou MTLC Electric Appliances Co.,Ltd. with the thing type UID of enerwave_zw15sm_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The ZW15SM supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
The on/off switch replaces your current light switch, uses your existing wiring, and provides in-wall control of overhead lighting and remote access.
The process of "Inclusion/ Exclusion" is to Add or Remove the device from the Hub. All Z-Wave devices must be "Included" on the Controller (Hub) before it can be controlled from a smart device. The Hub should be brought physically closer to the device just for the "Inclusion" process (recommended within 10ft). When finished, the Hub and device can be moved back to final installation location.
- Go to the "Add Device" page.
- Select "Include Device".
- When prompted, press the "ON" or "OFF" Button on the switch
- From the Control Panel, go the the device Exclusion page.
- Select "Exclude Device".
- When prompted, press the "ON" or "OFF" Button on the switch.
The following table summarises the channels available for the ZW15SM -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following table provides a summary of the 7 configuration parameters available in the ZW15SM. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | LED Toggle | Synchronization of load power and LED indicator |
| 2 | Button Toggle | Configure button toggle |
| 8 | METER_REPORT Instant Energy Interval | METER_REPORT Instant Energy Interval |
| 9 | Instant Energy Autosend Interval | Instant Energy Autosend Interval (SENSOR_MULTILEVEL_REPORT) |
| 10 | Accumulated Energy Autosend Interval report | Accumulated Energy Autosend Interval report (METER_REPORT) |
| 11 | Power change notification | Enable automatic notifications whenever there is a wattage change |
| 12 | Power change notification threshold | Minimum change in wattage report |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Synchronization of load power and LED indicator
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Power on, LED off |
| 1 | Power on, LED on |
The manufacturer defined default value is 0 (Power on, LED off).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Configure button toggle
Values in the range 0 to 1 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
METER_REPORT Instant Energy Interval Send METER_REPORT at this interval
0 means to not send Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Instant Energy Autosend Interval (SENSOR_MULTILEVEL_REPORT) Send SENSOR_MULTILEVEL_REPORT at this interval
0 means to not send Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Accumulated Energy Autosend Interval report (METER_REPORT) Send accumulated METER_REPORT at this interval
0 means to not send Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Enable automatic notifications whenever there is a wattage change Enable automatic notifications to associated device whenever there is a wattage change
0: No report
1: Send METER_REPORT
2: Send SENSOR_MULTILEVEL_REPORT
3: Send both METER_REPORT and SENSOR_MULTILEVEL_REPORT
Values in the range 0 to 3 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Minimum change in wattage report When the power changes by this many watts, send an automatic power level notification
0: 0.0W
....
255: 25.5W
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZW15SM supports 4 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Send device reset locally notification
Association group 1 supports 1 node.
Send basic report
Association group 2 supports 5 nodes.
Send meter power report
Association group 3 supports 5 nodes.
Send Basic set command
Association group 4 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.