| layout | title |
|---|---|
documentation |
DSC06 - ZWave |
{% include base.html %}
This describes the Z-Wave device DSC06, manufactured by AEON Labs with the thing type UID of aeon_dsc06_00_000.
The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.
The DSC06 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
The Aeon Labs Smart Energy Switch is a Z-Wave appliance switch which can report wattage energy usage or kWh energy usage to a Z-Wave gateway. It can also be controlled by other Z-Wave devices to turn on/off to save electricity when appropriate.
- Plug the Smart Energy Switch into an outlet
- Put the controller in inclusion mode
- Press the button located between the LED
If the Aeon Labs Smart Energy Switch was not successfully included into any Z-Wave network, the LED will be blinking. If the Aeon Labs Smart Energy Switch was successfully included to a Z-Wave network, the LED will either be on or off (depending on if the switch is on or off).
- Put the controller in exclusion mode
- Press the button located between the LED
If the Aeon Labs Smart Energy Switch was removed from the Z-Wave network, the LED will be blinking. If the Aeon Labs Smart Energy Switch was not successfully removed from the Z-Wave network, the LED will either be on or off (depending on if the switch is on or off).
The following table summarises the channels available for the DSC06 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Sensor (power) | sensor_power | sensor_power | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Indicates the energy consumption (kWh).
The sensor_power channel is of type sensor_power and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following table provides a summary of the 15 configuration parameters available in the DSC06. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Multilevel Sensor Report Content | |
| 80 | Automatic Notifications | Enable or disable automatic notifications |
| 90 | Enable/disable Parameter 91 and 92 | Enables/disables parameter 91 and 92 below |
| 91 | Minimum change in wattage | Minimum change in wattage to trigger event |
| 92 | Minimum change in wattage % | Minimum change in wattage % to trigger event |
| 100 | Set 101 to 103 to default values | |
| 101 | Group 1 report | |
| 102 | Group 2 report | |
| 103 | Group 3 report | |
| 110 | Set 111 to 113 to default values | |
| 111 | Interval Group 1 | The time interval (in seconds) for sending report to Group 1 |
| 112 | Interval Group 2 | The time interval (in seconds) for sending report to Group 2 |
| 113 | Interval Group 3 | The time interval (in seconds) for sending report to Group 3 |
| 254 | Device Tag | |
| 255 | Device Reset | |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Power |
| 1 | Voltage |
The manufacturer defined default value is 0 (Power).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Enable or disable automatic notifications Enables automatic notifications to associated devices whenever there is a state change (0=nothing, 1=hail CC, 2=basic CC report) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Nothing |
| 1 | Hail |
| 2 | Basic CC Report |
The manufacturer defined default value is 0 (Nothing).
This parameter has the configuration ID config_80_1 and is of type INTEGER.
Enables/disables parameter 91 and 92 below
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
The manufacturer defined default value is 0 (Disable).
This parameter has the configuration ID config_90_1 and is of type INTEGER.
Minimum change in wattage to trigger event The value here represents minimum change in wattage (in terms of wattage) for a REPORT to be sent. Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 50.
This parameter has the configuration ID config_91_2 and is of type INTEGER.
Minimum change in wattage % to trigger event The value here represents minimum change in wattage percent (in terms of percentage) for a REPORT to be sent. Values in the range 0 to 100 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_92_1 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No change |
| 1 | Reset |
The manufacturer defined default value is 0 (No change).
This parameter has the configuration ID config_100_1_wo and is of type INTEGER.
This is a write only parameter.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | None |
| 2 | Multisensor Report |
| 4 | Meter Report (Watts) |
| 8 | Meter Report (kWh) |
| 12 | Meter Report Watts and kWh |
The manufacturer defined default value is 8 (Meter Report (kWh)).
This parameter has the configuration ID config_101_4 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | None |
| 2 | Multisensor Report |
| 4 | Meter Report (Watts) |
| 8 | Meter Report (kWh) |
| 12 | Meter Report Watts and kWh |
The manufacturer defined default value is 0 (None).
This parameter has the configuration ID config_102_4 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | None |
| 2 | Multisensor Report |
| 4 | Meter Report (Watts) |
| 8 | Meter Report (kWh) |
| 12 | Meter Report Watts and kWh |
The manufacturer defined default value is 0 (None).
This parameter has the configuration ID config_103_4 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No change |
| 1 | Reset |
The manufacturer defined default value is 0 (No change).
This parameter has the configuration ID config_110_1_wo and is of type INTEGER.
This is a write only parameter.
The time interval (in seconds) for sending report to Group 1
Values in the range 1 to 65535 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_111_4 and is of type INTEGER.
The time interval (in seconds) for sending report to Group 2
Values in the range 1 to 65535 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_112_4 and is of type INTEGER.
The time interval (in seconds) for sending report to Group 3
Values in the range 1 to 65535 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_113_4 and is of type INTEGER.
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_254_2 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No change |
| 1 | Reset |
The manufacturer defined default value is 0 (No change).
This parameter has the configuration ID config_255_1_wo and is of type INTEGER.
This is a write only parameter.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The DSC06 supports 1 association group.
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V3 | |
| COMMAND_CLASS_METER_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.