Skip to content

Latest commit

 

History

History
142 lines (106 loc) · 9.36 KB

README.md

File metadata and controls

142 lines (106 loc) · 9.36 KB
Raw

Scalable KVM Over IP (SKVMOIP)

This repository contains source code for SKVMOIP project for Windows and Linux platforms written in C++.

Buy Me A Coffee

SKVMOIP_Setup

Currently supported Operating Systems:

drawing

Support in-progress Operating Systems:

drawing

Currently supported GPU vendors:

drawing

Support in-progress GPU vendors:

drawing

drawing

If you're a corporate and willing to sponsor me, feel free to reach me out at [email protected]!

Introduction

There are many options available in the market for KVM over IP, however most of them are either made for a corporate or very expensive for individuals - and still not scalable enough. Many people have built cheap solutions such as PiKVM and TinyPilot - but I still find them expensive given that they can only support one machine and one would need to spend more money to replicate over multiple machines.

Therefore, I started this project to invent a Scalable KVM Over IP software suite which can be installed on cheap hardware modules and on a client computer. This KVMK Over IP is scalable to any size because it uses ethernet wiring to communicate with the computers/servers with only one Encoder Server; hence no need to replicate the "pricy" hardware for each machine to be managed.

image

Features of SKVMOIP

  1. GPU Accelerated Video Decoding and Presenting the images on the display.
  2. Keyboard Over IP, works even to boot systems into their BIOS and without any software installed on the target system.
  3. Mouse Over IP, works even in the BIOS of the systems and without any software installed on the target system.
  4. Video Over IP, works even before the system boots and without any software installed on the target system.
  5. Power/Reset/HDDLED/PowerLED Over IP, turn On or Off the systems remotely just like you do onsite by pressing the power button.
  6. Easy to use Client software for Windows and Linux platforms.

What's in the Software Suite

  1. Firmware Software for STM32401CCU6 and W5500 WizChip
  2. Client Software for a Client Computer, called "SKVMOIP Client".
  3. Server Software for HDMI stream Encoder Server.

Hardware Requirements

  1. STM32F401CCU6 Microcontroller
    image

  2. W5500 Wizchip Ethernet Module
    image

  3. ST Link Programmer
    image

  4. HDMI capture device
    image

  5. A Video Encoder server computer (usually a mini PC with enough processing power, more quantitative data will be added here in future).

  6. A client computer either running Windows or Linux.

GPU Vendor Software Support Requirements

  1. Nvidia Cuda Toolkit
  2. Vulkan SDK

How to setup the SKVMOIP?

Installing and setting up the software suite is easy to follow and requires no special technical knowledge. However, currently only Windows in msys2 environment is supported.

  • Install Msys2 development environment from here
  • Launch the MSYS2 MINGW64 from start menu
  • Install gcc using $pacman -S mingw-w64-x86_64-gcc
  • Install make using $pacman -S mingw-w64-x86_64-make
  • Install git using $pacman -S git
  • Install glslang using $pacman -S mingw-w64-x86_64-glslang, this is only required for Client Build
  • Install gtk3 using $pacman -S mingw-w64-x86_64-gtk3, this is only required for Client Build
  • Clone this repository using $git clone https://github.com/ravi688/SKVMOIP
  • Change directory to SKVMOIP using $cd SKVMOIP`
  • Setup dependencies using $git submodule update --init

Setting up the STM32F401CCU6 and W5500 via SPI interface

Connect GND and 3.3 Vcc pins of the W5500 to the GND and 3.3 Vcc pins of STM32 MCU. Now check if the W5500 and STM32 MCU both are powering on (the red lights should light up on both).

Connect the MOSI, MISO, and CLOCK pins of the W5500 to the SPI1 pins of the STM32 MCU.

Connect the RST pin of W5500 to the one of the GPIO pins of STM32 MCU to enable reset function trigger from the STM32 MCU.

Setting up the STM32F401CCU6 Firmware

Install STM32Cube IDE in any Windows Computer, and load the project under the directory SKVMOIP/Firmware/STM32F401CCU6

Press the key combination Windows Logo Key + B to build the project and make sure there are no build errors.

Now, plug the ST link programmer to one of the USB ports of the computer (on which STM32Cube IDE has been installed).
NOTE: Before plugging the ST link programmer, make appropriate connections to the microcontroller's pins from some online guides.

Click on the Run tab on the menu bar on the top, and select run to build and upload the executable on the Microcontroller.

Setting up server for Windows

It requires building the server executable first and then deploying it to the encoder server computer (a windows computer).

  • cd into the git repo directory (on the server computer) using $cd SKVMOIP
  • Make sure to run $make -s clean for previous builds if any
  • Run $make -s build BUILD=server OUT=server, this will start the server build process image
  • And outputs a server.exe executable file
  • Run the application using ./server.exe
  • Now, note down the IP address and Port number at which the server is listening for connections
  • Done! image

Setting up client For Windows

It requires buildilng the installer first and then deploying it to a Windows Client Computer.

  • cd into the git repo directory (on the client computer) using $cd SKVMOIP

  • Make sure to run $make -s clean for previous builds if any

  • Run $make -s build BUILD=client OUT=client, this will start the client build process image image

  • And outputs a client.exe executable file

  • Run the application using ./client.exe

  • Now click on Add button on the top right, you'll be shown a machine add wizard window

  • Fill in the Machine details, VIP is the Video Server IP address reported by the SKVMOIP server process and the KMIP is the Keyboard Mouse Server IP address which is set to 192.168.1.113:2000, and click Ok
    image

  • After that, select the newly added machine and click on Connect button to handshake with both the video and km servers.

  • Once, the connection has been established, you would need to click on Video button to start using Remote Desktop.

  • Done!

Setting up client For Linux

In-Progress

Keyboard Shortcuts while using the Client Software

  1. Ctrl + Alt + Enter -> toggle Fullscreen; by default, when a session starts the window opens in full screen mode. You can switch back to a Windowed mode by pressing Ctrl + Alt + Enter in order.
  2. Ctrl + Alt + K -> toggle focus and cursor lock; by default, when a session starts the cursor is locked and invisible so that you can easily work on the remote Computer. You can get out of that by pressing Ctrl + Alt + K in order.

TODO

  1. Add HDMI Routing over IP support to scale Video Over IP across local networks (as LANs are very fast, can handle the RAW HDMI data).'
  2. Add support for USB Mass Storage over IP to enable the host computer boot from a remote USB flash drive or Computer acting as a USB flash drive. However, PXE boot already exists.
  3. Add support for Audio Over IP

License

                             Apache License
                       Version 2.0, January 2004
                    http://www.apache.org/licenses/
                    (See: LICENSE file, for more info)