gridfinity_basic_cup.scad

// Gridfinity extended basic cup
// version 2024-02-17
//
// Source
// https://www.printables.com/model/630057-gridfinity-extended-openscad
//
// Documentation
// https://docs.ostat.com/docs/openscad/gridfinity-extended/basic-cup.html

include <modules/gridfinity_constants.scad>
use <modules/module_gridfinity_cup.scad>
use <modules/module_gridfinity.scad>

/*<!!start gridfinity_basic_cup!!>*/
/* [General Cup] */
// X dimension. grid units (multiples of 42mm) or mm.
width = [2, 0]; //0.1
// Y dimension. grid units (multiples of 42mm) or mm.
depth = [1, 0]; //0.1
// Z dimension excluding. grid units (multiples of 7mm) or mm.
height = [3, 0]; //0.1
// Fill in solid block (overrides all following options)
filled_in = "disabled"; //[disabled, enabled, enabledfilllip:"Fill cup and lip"]
// Wall thickness of outer walls. default, height < 8 0.95, height < 16 1.2, height > 16 1.6 (Zack's design is 0.95 mm)
wall_thickness = 0;  // .01
// Remove some or all of lip
lip_style = "normal";  // [ normal, reduced, minimum, none:not stackable ]
//under size the bin top by this amount to allow for better stacking
zClearance = 0; // 0.1

/* [Subdivisions] */
chamber_wall_thickness = 1.2;
//Reduce the wall height by this amount
chamber_wall_zClearance = 0;//0.1
// X dimension subdivisions
vertical_chambers = 1; 
vertical_separator_bend_position = 0;
vertical_separator_bend_angle = 0;
vertical_separator_bend_separation = 0;
vertical_separator_cut_depth=0;
horizontal_chambers = 1; 
horizontal_separator_bend_position = 0;
horizontal_separator_bend_angle = 0;
horizontal_separator_bend_separation = 0;
horizontal_separator_cut_depth=0;
// Enable irregular subdivisions
vertical_irregular_subdivisions = false;
// Separator positions are defined in terms of grid units from the left end
vertical_separator_config = "10.5|21|42|50|60";
// Enable irregular subdivisions
horizontal_irregular_subdivisions = false;
// Separator positions are defined in terms of grid units from the left end
horizontal_separator_config = "10.5|21|42|50|60";

/* [Base] */
// Enable magnets
enable_magnets = true;
// Enable screws
enable_screws = true;
//size of magnet, diameter and height. Zack's original used 6.5 and 2.4
magnet_size = [6.5, 2.4];  // .1
//create relief for magnet removal
magnet_easy_release = "auto";//["off","auto","inner","outer"] 
//size of screw, diameter and height. Zack's original used 3 and 6
screw_size = [3, 6]; // .1
//size of center magnet, diameter and height. 
center_magnet_size = [0,0];
// Sequential Bridging hole overhang remedy is active only when both screws and magnets are nonzero (and this option is selected)
hole_overhang_remedy = 2;
//Only add attachments (magnets and screw) to box corners (prints faster).
box_corner_attachments_only = true;
// Minimum thickness above cutouts in base (Zack's design is effectively 1.2)
floor_thickness = 0.7;
cavity_floor_radius = -1;// .1
// Efficient floor option saves material and time, but the internal floor is not flat
efficient_floor = "off";//[off,on,rounded,smooth]
// Enable to subdivide bottom pads to allow half-cell offsets
half_pitch = false;
// Removes the internal grid from base the shape
flat_base = "off"; // [off, gridfinity:gridfinity stackable, rounded]
// Remove floor to create a vertical spacer
spacer = false;
//Pads smaller than this will not be rendered as it interferes with the baseplate. Ensure appropriate support is added in slicer.
minimum_printable_pad_size = 0.2;

// Adjust the radius of the rounded flat base. -1 uses the corner radius.
flat_base_rounded_radius = -1;
// Add chamfer to the rounded bottom corner to make easier to print. -1 add auto 45deg.
flat_base_rounded_easyPrint = -1;

/* [Label] */
label_style = "normal"; //[disabled: no label, normal:normal, gflabel:gflabel basic label, pred:pred - labels by pred, cullenect:Cullenect click labels V2,  cullenect_legacy:Cullenect click labels v1]
// Include overhang for labeling (and specify left/right/center justification)
label_position = "left"; // [left, right, center, leftchamber, rightchamber, centerchamber]
// Width, Depth, Height, Radius. Width in Gridfinity units of 42mm, Depth and Height in mm, radius in mm. Width of 0 uses full width. Height of 0 uses Depth, height of -1 uses depth*3/4. 
label_size = [0,14,0,0.6]; // 0.01
// Size in mm of relief where appropriate. Width, depth, height, radius
label_relief = [0,0,0,0.6]; // 0.1
// wall to enable on, front, back, left, right. 0: disabled; 1: enabled;
label_walls=[0,1,0,0];  //[0:1:1]
    
/* [Sliding Lid] */
sliding_lid_enabled = false;
// 0 = wall thickness *2
sliding_lid_thickness = 0; //0.1
// 0 = wall_thickness/2
sliding_min_wallThickness = 0;//0.1
// 0 = default_sliding_lid_thickness/2
sliding_min_support = 0;//0.1
sliding_clearance = 0.1;//0.1
sliding_lid_lip_enabled = false;

/* [Finger Slide] */
// Include larger corner fillet
fingerslide = "none"; //[none, rounded, chamfered]
// Radius of the corner fillet
fingerslide_radius = 8;
// wall to enable on, front, back, left, right. 0: disabled; 1: enabled;
fingerslide_walls=[1,0,0,0];  //[0:1:1]
//Align the fingerslide with the lip
fingerslide_lip_aligned=true; 

/* [Tapered Corner] */
tapered_corner = "none"; //[none, rounded, chamfered]
tapered_corner_size = 10;
// Set back of the tapered corner, default is the gridfinity corner radius
tapered_setback = -1;//gridfinity_corner_radius/2;

/* [Wall Pattern] */
// Grid wall patter
wallpattern_enabled=false;
// Style of the pattern
wallpattern_style = "gridrotated"; //[grid, gridrotated, hexgrid, hexgridrotated, voronoi, voronoigrid, voronoihexgrid, brick, brickrotated, brickoffset, brickoffsetrotated]
// Spacing between pattern
wallpattern_hole_spacing = 2; //0.1
// wall to enable on, front, back, left, right.
wallpattern_walls=[1,1,1,1];  //[0:1:1]
// Add the pattern to the dividers
wallpattern_dividers_enabled="disabled"; //[disabled, horizontal, vertical, both] 
//Number of sides of the hole op
wallpattern_hole_sides = 6; //[4:square, 6:Hex, 64:circle]
//Size of the hole
wallpattern_hole_size = [5,5]; //0.1
//Radius of corners
wallpattern_hole_radius = 0.5;
// pattern fill mode
wallpattern_fill = "crop"; //[none, space, crop, crophorizontal, cropvertical, crophorizontal_spacevertical, cropvertical_spacehorizontal, spacevertical, spacehorizontal]
//voronoi: noise, brick: center weight, grid: taper
wallpattern_pattern_variable = 0.75;
//$fs for floor pattern, min size face.
wallpattern_pattern_quality = 0.4;//0.1:0.1:2

/* [Floor Pattern] */
// enable Grid floor patter
floorpattern_enabled=false;
// Style of the pattern
floorpattern_style = "gridrotated"; //[grid, gridrotated, hexgrid, hexgridrotated, voronoi, voronoigrid, voronoihexgrid, brick, brickrotated, brickoffset, brickoffsetrotated]
// Spacing between pattern
floorpattern_hole_spacing = 2; //0.1
//Number of sides of the hole op
floorpattern_hole_sides = 6; //[4:square, 6:Hex, 64:circle]
//Size of the hole
floorpattern_hole_size = [5,5]; //0.1
floorpattern_hole_radius = 0.5;
// pattern fill mode
floorpattern_fill = "crop"; //[none, space, crop, crophorizontal, cropvertical, crophorizontal_spacevertical, cropvertical_spacehorizontal, spacevertical, spacehorizontal]
//voronoi: noise, brick: center weight, grid: taper
floorpattern_pattern_variable = 0.75;
//$fs for floor pattern, min size face.
floorpattern_pattern_quality = 0.4;//0.1:0.1:2

/* [Wall Cutout] */
wallcutout_vertical ="disabled"; //[disabled, enabled, wallsonly, frontonly, backonly]
// wall to enable on, front, back, left, right. 0: disabled; Positive: GF units; Negative: ratio length/abs(value)
wallcutout_vertical_position=-2;  //0.1
//default will be binwidth/2
wallcutout_vertical_width=0;
wallcutout_vertical_angle=70;
//default will be binHeight
wallcutout_vertical_height=0;
wallcutout_vertical_corner_radius=5;
wallcutout_horizontal ="disabled"; //[disabled, enabled, wallsonly, leftonly, rightonly]
// wall to enable on, front, back, left, right. 0: disabled; Positive: GF units; Negative: ratio length/abs(value)
wallcutout_horizontal_position=-2;  //0.1
//default will be binwidth/2
wallcutout_horizontal_width=0;
wallcutout_horizontal_angle=70;
//default will be binHeight
wallcutout_horizontal_height=0;
wallcutout_horizontal_corner_radius=5;

/* [Extendable] */
extension_x_enabled = "disabled"; //[disabled, front, back]
extension_x_position = 0.5; 
extension_y_enabled = "disabled"; //[disabled, front, back]
extension_y_position = 0.5; 
extension_tabs_enabled = true;
//Tab size, height, width, thickness, style. width default is height, thickness default is 1.4, style {0,1,2}.
extension_tab_size= [10,0,0,0];

/* [Bottom Text] */
// Add bin size to bin bottom
text_1 = false;
// Font Size of text, in mm (0 will auto size)
text_size = 0; // 0.1
// Depth of text, in mm
text_depth = 0.3; // 0.01
// Font to use
text_font = "Aldo";  // [Aldo, B612, "Open Sans", Ubuntu]
// Add free-form text line to bin bottom (printing date, serial, etc)
text_2 = false;
// Actual text to add
text_2_text = "Gridfinity Extended";

/* [debug] */
//Slice along the x axis
cutx = 0; //0.1
//Slice along the y axis
cuty = 0; //0.1
// enable loging of help messages during render.
enable_help = "disabled"; //[info,debug,trace]

/* [Model detail] */
//assign colours to the bin, will may 
set_colour = "enable"; //[disabled, enable, preview, lip]
//where to render the model
render_position = "center"; //[default,center,zero]
// minimum angle for a fragment (fragments = 360/fa).  Low is more fragments 
$fa = 6; 
// minimum size of a fragment.  Low is more fragments
$fs = 0.1; 
// number of fragments, overrides $fa and $fs
$fn = 0;  
// set random seed for 
random_seed = 0; //0.0001
// force render on costly components
force_render = true;

/* [Hidden] */
module end_of_customizer_opts() {}
/*<!!end gridfinity_basic_cup!!>*/

SetGridfinityEnvironment(
  width = width,
  depth = depth,
  height = height,
  render_position = render_position,
  help = enable_help,
  cutx = cutx,
  cuty = cuty,
  cutz = calcDimensionHeight(height, true),
  setColour = set_colour,
  randomSeed = random_seed,
  force_render = force_render)
gridfinity_cup(
  width=width, depth=depth, height=height,
  filled_in=filled_in,
  label_settings=LabelSettings(
    labelStyle=label_style, 
    labelPosition=label_position, 
    labelSize=label_size,
    labelRelief=label_relief,
    labelWalls=label_walls),
  fingerslide=fingerslide,
  fingerslide_radius=fingerslide_radius,
  fingerslide_walls=fingerslide_walls,
  fingerslide_lip_aligned=fingerslide_lip_aligned,
  cupBase_settings = CupBaseSettings(
    magnetSize = enable_magnets?magnet_size:[0,0],
    magnetEasyRelease = magnet_easy_release, 
    centerMagnetSize = center_magnet_size, 
    screwSize = enable_screws?screw_size:[0,0],
    holeOverhangRemedy = hole_overhang_remedy, 
    cornerAttachmentsOnly = box_corner_attachments_only,
    floorThickness = floor_thickness,
    cavityFloorRadius = cavity_floor_radius,
    efficientFloor=efficient_floor,
    halfPitch=half_pitch,
    flatBase=flat_base,
    spacer=spacer,
    minimumPrintablePadSize=minimum_printable_pad_size,
    flatBaseRoundedRadius = flat_base_rounded_radius,
    flatBaseRoundedEasyPrint = flat_base_rounded_easyPrint),
  wall_thickness=wall_thickness,
  chamber_wall_thickness=chamber_wall_thickness,
  chamber_wall_zClearance=chamber_wall_zClearance,
  vertical_chambers = vertical_chambers,
  vertical_separator_bend_position=vertical_separator_bend_position,
  vertical_separator_bend_angle=vertical_separator_bend_angle,
  vertical_separator_bend_separation=vertical_separator_bend_separation,
  vertical_separator_cut_depth=vertical_separator_cut_depth,
  vertical_irregular_subdivisions=vertical_irregular_subdivisions,
  vertical_separator_config=vertical_separator_config,
  horizontal_chambers=horizontal_chambers,
  horizontal_separator_bend_position=horizontal_separator_bend_position,
  horizontal_separator_bend_angle=horizontal_separator_bend_angle,
  horizontal_separator_bend_separation=horizontal_separator_bend_separation,
  horizontal_separator_cut_depth=horizontal_separator_cut_depth,
  horizontal_irregular_subdivisions=horizontal_irregular_subdivisions,
  horizontal_separator_config=horizontal_separator_config, 
  lip_style=lip_style,
  zClearance=zClearance,
  tapered_corner=tapered_corner,
  tapered_corner_size = tapered_corner_size,
  tapered_setback = tapered_setback,
  wallpattern_walls=wallpattern_walls, 
  wallpattern_dividers_enabled=wallpattern_dividers_enabled,
  wall_pattern_settings = PatternSettings(
    patternEnabled = wallpattern_enabled, 
    patternStyle = wallpattern_style, 
    patternFill = wallpattern_fill,
    patternBorder = wallpattern_hole_spacing, 
    patternHoleSize = wallpattern_hole_size, 
    patternHoleSides = wallpattern_hole_sides,
    patternHoleSpacing = wallpattern_hole_spacing, 
    patternHoleRadius = wallpattern_hole_radius,
    patternVariable = wallpattern_pattern_variable,
    patternFs = wallpattern_pattern_quality), 
  floor_pattern_settings = PatternSettings(
    patternEnabled = floorpattern_enabled, 
    patternStyle = floorpattern_style, 
    patternFill = floorpattern_fill,
    patternBorder = floorpattern_hole_spacing, 
    patternHoleSize = floorpattern_hole_size, 
    patternHoleSides = floorpattern_hole_sides,
    patternHoleSpacing = floorpattern_hole_spacing, 
    patternHoleRadius = floorpattern_hole_radius,
    patternVariable = floorpattern_pattern_variable,
    patternFs = floorpattern_pattern_quality), 
  wallcutout_vertical=wallcutout_vertical,
  wallcutout_vertical_position=wallcutout_vertical_position,
  wallcutout_vertical_width=wallcutout_vertical_width,
  wallcutout_vertical_angle=wallcutout_vertical_angle,
  wallcutout_vertical_height=wallcutout_vertical_height,
  wallcutout_vertical_corner_radius=wallcutout_vertical_corner_radius,
  wallcutout_horizontal=wallcutout_horizontal,
  wallcutout_horizontal_position=wallcutout_horizontal_position,
  wallcutout_horizontal_width=wallcutout_horizontal_width,
  wallcutout_horizontal_angle=wallcutout_horizontal_angle,
  wallcutout_horizontal_height=wallcutout_horizontal_height,
  wallcutout_horizontal_corner_radius=wallcutout_horizontal_corner_radius,
  extendable_Settings = ExtendableSettings(
    extendablexEnabled = extension_x_enabled, 
    extendablexPosition = extension_x_position, 
    extendableyEnabled = extension_y_enabled, 
    extendableyPosition = extension_y_position, 
    extendableTabsEnabled = extension_tabs_enabled, 
    extendableTabSize = extension_tab_size),
  sliding_lid_enabled = sliding_lid_enabled, 
  sliding_lid_thickness = sliding_lid_thickness, 
  sliding_min_wall_thickness = sliding_min_wallThickness, 
  sliding_min_support = sliding_min_support, 
  sliding_clearance = sliding_clearance,
  sliding_lid_lip_enabled=sliding_lid_lip_enabled,
  cupBaseTextSettings = CupBaseTextSettings(
    baseTextLine1Enabled = text_1,
    baseTextLine2Enabled = text_2,
    baseTextLine2Value = text_2_text,
    baseTextFontSize = text_size,
    baseTextFont = text_font,
    baseTextDepth = text_depth));