ASA show failover bug when using IPS module

[danielgurau]

ISSUE TYPE

• Bug Report

TEMPLATE USING

cisco_asa_show_failover.template

SAMPLE COMMAND OUTPUT

Failover On
Failover unit Secondary
Failover LAN Interface: Failover GigabitEthernet0/7 (up)
Reconnect timeout 0:00:00
Unit Poll frequency 1 seconds, holdtime 4 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 7 of 1049 maximum
MAC Address Move Notification Interval not set
failover replication http
Version: Ours 9.6(4)34, Mate 9.6(4)34
Serial Number: Ours JAD163903TY, Mate JAD163900D6
Last Failover at: 19:38:08 UTC Nov 4 2019
        This host: Secondary - Active
                Active time: 1450749 (sec)
                slot 0: ASA5585-SSP-20 hw/sw rev (2.0/9.6(4)34) status (Up Sys)
                  il2-admin Interface skyscape_admin (1.1.1.1): Normal (Monitored)
                  fwname Interface skyscape_mgmt (1.1.1.1): Normal (Not-Monitored)
                  fwname Interface avamar_drac (1.1.1.1): Normal (Monitored)
				  <omited output>	
                slot 1: ASA5585-SSP-IPS20 hw/sw rev (2.0/7.3(5)E4) status (Up/Up)
                  IPS, 7.3(5)E4, Up, (Monitored)
        Other host: Primary - Standby Ready
                Active time: 425691 (sec)
                slot 0: ASA5585-SSP-20 hw/sw rev (2.0/9.6(4)34) status (Up Sys)
                  il2-admin Interface skyscape_admin (2.2.2.2): Normal (Monitored)
                  fwname Interface skyscape_mgmt (2.2.2.2): Normal (Not-Monitored)
                  fwname Interface avamar_drac (2.2.2.2): Normal (Monitored)
				  <omited output>
                slot 1: ASA5585-SSP-IPS20 hw/sw rev (2.0/7.3(5)E4) status (Up/Up)
                  IPS, 7.3(5)E4, Up, (Monitored)

Stateful Failover Logical Update Statistics
        Link : StateFailover GigabitEthernet0/6 (up)
        Stateful Obj    xmit       xerr       rcv        rerr
        General         2455641256 0          628699983  1699
        sys cmd         250128     0          250128     0
        up time         0          0          0          0
        RPC services    0          0          0          0
        TCP conn        1441746676 0          398760885  0
        UDP conn        635150912  0          113869522  1697
        ARP tbl         378487541  0          115817628  0
        Xlate_Timeout   0          0          0          0
        IPv6 ND tbl     5985       0          1729       0
        VPN IKEv1 SA    0          0          0          0
        VPN IKEv1 P2    0          0          0          0
        VPN IKEv2 SA    0          0          0          0
        VPN IKEv2 P2    0          0          0          0
        VPN CTCP upd    0          0          0          0
        VPN SDI upd     0          0          0          0
        VPN DHCP upd    0          0          0          0
        SIP Session     0          0          0          0
        SIP Tx  0          0          0          0
        SIP Pinhole     0          0          0          0
        Route Session   14         0          0          2
        Router ID       0          0          0          0
        User-Identity   0          0          91         0
        CTS SGTNAME     0          0          0          0
        CTS PAC         0          0          0          0
        TrustSec-SXP    0          0          0          0
        IPv6 Route      0          0          0          0
        STS Table       0          0          0          0

        Logical Update Queue Information
                        Cur     Max     Total
        Recv Q:         0       140     651732837
        Xmit Q:         0       3       2527845901

SUMMARY

When running ssh_conn.send_command('show failover', use_textfsm=True), I get an error:

TextFSMError: State Error raised. Rule Line: 62. Input Line:              IPS, 7.3(5)E4, Up, (Monitored)

STEPS TO REPRODUCE

ssh_conn.send_command('show failover', use_textfsm=True)

EXPECTED RESULTS

Expected this to run and not return ERROR

ACTUAL RESULTS

TextFSMError: State Error raised. Rule Line: 62. Input Line:              IPS, 7.3(5)E4, Up, (Monitored)