MHS40-show

#!/bin/bash

sudo ./system_backup.sh

if [ -f /etc/X11/xorg.conf.d/40-libinput.conf ]; then
sudo rm -rf /etc/X11/xorg.conf.d/40-libinput.conf
fi
if [ ! -d /etc/X11/xorg.conf.d ]; then
sudo mkdir -p /etc/X11/xorg.conf.d
fi
sudo cp ./usr/mhs395-overlay.dtb /boot/overlays/
sudo cp ./usr/mhs395-overlay.dtb /boot/overlays/mhs395.dtbo

source ./system_config.sh
#sudo cp -rf ./boot/config-nomal.txt ./boot/config.txt.bak
sudo echo "hdmi_force_hotplug=1" >> ./boot/config.txt.bak
sudo echo "dtparam=i2c_arm=on" >> ./boot/config.txt.bak
sudo echo "dtparam=spi=on" >> ./boot/config.txt.bak
sudo echo "enable_uart=1" >> ./boot/config.txt.bak
sudo echo "dtoverlay=mhs395:rotate=90" >> ./boot/config.txt.bak
sudo echo "hdmi_group=2" >> ./boot/config.txt.bak
sudo echo "hdmi_mode=1" >> ./boot/config.txt.bak
sudo echo "hdmi_mode=87" >> ./boot/config.txt.bak
sudo echo "hdmi_cvt 480 320 60 6 0 0 0" >> ./boot/config.txt.bak
sudo echo "hdmi_drive=2" >> ./boot/config.txt.bak
sudo cp -rf ./boot/config.txt.bak /boot/config.txt
sudo cp -rf ./usr/99-calibration.conf-mhs395-90  /etc/X11/xorg.conf.d/99-calibration.conf
if [ $hardware_model -eq 5 ]; then
sudo cp -rf ./usr/99-fbturbo-PI5.conf  /usr/share/X11/xorg.conf.d/99-fbturbo.conf
else
sudo cp -rf ./usr/99-fbturbo.conf  /usr/share/X11/xorg.conf.d/99-fbturbo.conf
fi
if [ -b /dev/mmcblk0p7 ]; then
sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
else
sudo cp ./usr/cmdline.txt /boot/
fi
#sudo cp ./usr/inittab /etc/
#sudo cp ./boot/config-mhs395.txt /boot/config.txt
sudo touch ./.have_installed
echo "gpio:resistance:mhs395:90:480:320" > ./.have_installed

#FBCP install
#wget --spider -q -o /dev/null --tries=1 -T 10 https://github.com
#if [ $? -eq 0 ]; then
#sudo cp -rf ./usr/99-fbturbo-fbcp.conf  /usr/share/X11/xorg.conf.d/99-fbturbo.conf
#sudo cp -rf ./etc/rc.local /etc/rc.local
#sudo apt-get update
#sudo apt-get install git cmake libraspberrypi-dev -y 2> error_output.txt
#result=`cat ./error_output.txt`
#echo -e "\033[31m$result\033[0m"
#grep -q "^E:" ./error_output.txt && exit
#sudo rm -rf rpi-fbcp
#sudo git clone https://github.com/tasanakorn/rpi-fbcp
#sudo mkdir ./rpi-fbcp/build
#cd ./rpi-fbcp/build/
#sudo cmake ..
#sudo make
#sudo install fbcp /usr/local/bin/fbcp
#cd - > /dev/null
#fi
##evdev install
#nodeplatform=`uname -n`
#kernel=`uname -r`
#version=`uname -v`
#version=`lsb_release -r|awk -F ' ' '{printf $2}'`
#if test "$nodeplatform" = "raspberrypi";then
#echo "this is raspberrypi kernel"
#version=${version%% *}
#version=${version#*#}
echo $version
#if test $version -lt 970;then
if [[ "$version" = "2020.2" ]] || [[ "$version" > "2020.2" ]]; then
#echo "reboot"
#else
echo "need to update touch configuration"
wget --spider -q -o /dev/null --tries=1 -T 10 https://www.x.org
if [ $? -eq 0 ]; then
sudo apt-get update
sudo apt-get install xserver-xorg-input-evdev  2> error_output.txt
else
if [ $hardware_arch -eq 32 ]; then
sudo dpkg -i -B ./xserver-xorg-input-evdev_1%3a2.10.6-2_armhf.deb 2> error_output.txt
elif [ $hardware_arch -eq 64 ]; then
sudo dpkg -i -B ./xserver-xorg-input-evdev_1%3a2.10.6-2+b1_arm64.deb 2> error_output.txt
fi
fi
#sudo dpkg -i -B ./xserver-xorg-input-evdev_1%3a2.10.6-2_armhf.deb 2> error_output.txt
##sudo apt-get install xserver-xorg-input-evdev  2> error_output.txt
result=`cat ./error_output.txt`
echo -e "\033[31m$result\033[0m"
grep -q "error:" ./error_output.txt && exit
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
##echo "reboot"
#fi
else
echo "This version is lower than kali 2020.2, no need to update touch configure, reboot"
fi

sudo sync
sudo sync
sleep 1
if [ $# -eq 1 ]; then
sudo ./rotate.sh $1
elif [ $# -gt 1 ]; then
echo "Too many parameters"
fi

echo "reboot now"
sudo reboot