tplink_c200_serial.txt

U-Boot 2014.01-v1.2 (Jan 19 2020 - 14:59:28)
Board: IPCAM RTS3903 CPU: 500M :rx5281 prid=0xdc02
force spi nor mode
DRAM:  64 MiB @ 1066 MHz
Skipping flash_init
Flash: 0 Bytes
flash status is 0, 0, 0
SF: Detected XM25QH64A with page size 256 Bytes, erase size 64 KiB, total 8 MiB
Using default environment

Autobooting in 1 seconds
copying flash to 0x81500000
flash status is 0, 0, 0
SF: Detected XM25QH64A with page size 256 Bytes, erase size 64 KiB, total 8 MiB
SF: 8388608 bytes @ 0x0 Read: OK

verifying uboot partition...
ok

verifying kernel and romfs partition...
ok

set watchdog, resetting...

U-Boot 2014.01-v1.2 (Jan 19 2020 - 15:00:37)
Board: IPCAM RTS3903 CPU: 500M :rx5281 prid=0xdc02
force spi nor mode
DRAM:  64 MiB @ 1066 MHz
flash status is 0, 0, 0
SF: Detected XM25QH64A with page size 256 Bytes, erase size 64 KiB, total 8 MiB
Flash: 0 Bytes
flash status is 0, 0, 0
SF: Detected XM25QH64A with page size 256 Bytes, erase size 64 KiB, total 8 MiB

Using default environment
In:    serial
Out:   serial
Err:   serial
Net:   Realtek PCIe GBE Family Controller mcfg = 0024
new_ethaddr = 00:00:00:00:00:00
r8168#0

Autobooting in 1 seconds
flash status is 0, 0, 0

SF: Detected XM25QH64A with page size 256 Bytes, erase size 64 KiB, total 8 MiB
SF: 3145728 bytes @ 0x60000 Read: OK
## Booting image at 82000000 ...

Uncompressing Kernel Image ... OK
Starting kernel ...
[    0.000000] Linux version 3.10.27 (jenkins@sohoicamerabuild) (gcc version 4.8.5 20150209 (prerelease) (Realtek RSDK-4.8.5p1 Build 2521) ) #1 PREEMPT Sun Jan 19 15:06:51 CST 2020
[    0.000000] prom cpufreq = 500000000
[    0.000000] prom memsize = 67108864
[    0.000000] hw_ver: 0x2, hw_rev: 0x1, isp_ver: 0x1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0000dc02
[    0.000000] FPU revision is: 01730001
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Reserved contiguous memory at 0x450000(0x13ec000)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] icache: 32kB/32B, dcache: 16kB/32B, scache: 0kB/0B
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,57600 root=/dev/mtdblock6 rts-quadspi.channels=dual
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 40116k/65536k available (3073k kernel code, 25420k reserved, 1028k data, 184k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:57
[    0.001000] Calibrating delay loop... 497.66 BogoMIPS (lpj=248832)
[    0.012000] pid_max: default: 32768 minimum: 301
[    0.013000] Mount-cache hash table entries: 512
[    0.016000] pinctrl core: initialized pinctrl subsystem
[    0.017000] NET: Registered protocol family 16
[    0.018000] Init force reset registers
[    0.019000] rtsxb2 registered with IRQs
[    0.020000] INFO: initializing ISP memory ...
[    0.021000] INFO: initializing ISP device ...
[    0.022000] ISP camera platform devices added
[    0.023000] INFO: initializing SD controller ...
[    0.024000] INFO: initializing snd device ...
[    0.025000] snd resvd mem size : 524288
[    0.026000] INFO: initializing USB host ...
[    0.027000] INFO: initializing spi host ...0
[    0.028000] spi platform id is ffffffff
[    0.029000] INFO: initializing I2C master ...
[    0.030000] INFO: initializing DMA controller ...
[    0.031000] INFO: initializing adc ...
[    0.032000] INFO: initializing pinctrl device ...
[    0.033000] pinctrl_platform rts3903-pinctrl: rtspc registered with IRQs
[    0.034000] INFO: initializing ethernet devices ...
[    0.035000] INFO: initializing USB phy ...
[    0.036000] INFO: initializing watchdog controller ...
[    0.037000] INFO: initializing PWM controller ...
[    0.038000] INFO: initializing crypto device ...
[    0.052000] bio: create slab <bio-0> at 0
[    0.053000] rts_dmac rts3903-dmac: DesignWare DMA Controller, 4 channels
[    0.054000] INFO: realtek DMA engine inited
[    0.055000] usbcore: registered new interface driver usbfs
[    0.056000] usbcore: registered new interface driver hub
[    0.057000] usbcore: registered new device driver usb
[    0.058000] usbphy-platform usbphy-platform: Initialized Realtek IPCam USB Phy module
[    0.059000] Linux video capture interface: v2.00
[    0.060000] Advanced Linux Sound Architecture Driver Initialized.
[    0.062000] NET: Registered protocol family 2
[    0.071000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.084000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.097000] TCP: Hash tables configured (established 512 bind 512)
[    0.109000] TCP: reno registered
[    0.116000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.127000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.140000] NET: Registered protocol family 1
[    0.154000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.166000] msgmni has been set to 78
[    0.175000] NET: Registered protocol family 38
[    0.184000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.198000] io scheduler noop registered
[    0.206000] io scheduler deadline registered
[    0.215000] io scheduler cfq registered (default)
[    0.224000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    0.237000] serial8250: ttyS0 at MMIO 0x18810000 (irq = 6) is a 16550A
[    0.250000] console [ttyS1] enabled, bootconsole disabled
[    0.250000] console [ttyS1] enabled, bootconsole disabled
[    0.272000] serial8250: ttyS1 at MMIO 0x18810100 (irq = 6) is a 16550A
[    0.285000] serial8250: ttyS2 at MMIO 0x18810200 (irq = 6) is a 16550A
[    0.298000] dbg_iomem initialized!
[    0.306000] rts-quadspi rts3903-qspi: force to set channels from quad mode to dual mode
[    0.322000] rts-quadspi rts3903-qspi: request 60000000 Hz, force to set 41666666 Hz
[    0.337000] rts-quadspi rts3903-qspi: found XM25QH64A, expected mx25l12835f
[    0.351000] rts-quadspi rts3903-qspi: XM25QH64A (8192 Kbytes)
[    0.363000] Searching for RedBoot partition table
[    0.372000] 9 RedBoot partitions found on MTD device m25p80
[    0.383000] Creating 9 MTD partitions on "m25p80":
[    0.393000] 0x000000000000-0x00000001d800 : "factory_boot"
[    0.404000] mtd: partition "factory_boot" doesn't end on an erase block -- force read-only
[    0.421000] 0x00000001d800-0x000000020000 : "factory_info"
[    0.432000] mtd: partition "factory_info" doesn't start on an erase block boundary -- force read-only
[    0.452000] 0x000000020000-0x000000040000 : "art"
[    0.462000] 0x000000040000-0x000000050000 : "config"
[    0.472000] 0x000000050000-0x000000060000 : "boot"
[    0.483000] 0x000000060000-0x0000001c6400 : "kernel"
[    0.493000] mtd: partition "kernel" doesn't end on an erase block -- force read-only
[    0.509000] 0x0000001c6400-0x000000710000 : "rootfs"
[    0.519000] mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
[    0.537000] 0x000000710000-0x000000800000 : "rootfs_data"
[    0.549000] 0x000000060000-0x000000800000 : "firmware"
[    0.560000] rts-quadspi rts3903-qspi: Realtek QSPI Controller at 0x18030000 (irq 5)
[    0.575000] rtl8168 Gigabit Ethernet driver 8.038.00-NAPI loaded
[    0.676000] rtl8168 rts3903-rtl8168 (unregistered net_device): Get invalid MAC address from flash!
[    0.694000] eth%d: 0xb8400000, 00:00:00:00:00:00, IRQ 10
[    0.706000] PPP generic driver version 2.4.2
[    0.714000] PPP MPPE Compression module registered
[    0.724000] NET: Registered protocol family 24
[    0.733000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.746000] ehci-rts: ehci-rts platform driver
[    0.755000] ehci-platform ehci-platform: EHCI Host Controller
[    0.767000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    0.783000] ehci-platform ehci-platform: irq 11, io mem 0x18100000
[    0.801000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    0.813000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.827000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.841000] usb usb1: Product: EHCI Host Controller
[    0.851000] usb usb1: Manufacturer: Linux 3.10.27 ehci_hcd
[    0.862000] usb usb1: SerialNumber: ehci-platform
[    0.872000] hub 1-0:1.0: USB hub found
[    0.880000] hub 1-0:1.0: 1 port detected
[    0.888000] i2c /dev entries driver
[    0.895000] rtscam:isp resvd mem addr : 0x004d0000, size : 0x136c000
[    0.910000] rtscam:rtscam_mem_init v:0xa04d0000 p:0x004d0000 s:0x0000136c
[    0.924000] rtscam:rtscam_lock_init
[    0.931000] rtscam:rtscam_soc_probe
[    0.938000] rtscam:rtscam_hx280_probe
[    0.950000] rtscam:hx280enc:HW at base <0x18060000> with ID <0x48317011>
[    0.964000] rtscam:rtscam_jpgenc_probe
[    0.976000] rtscam:rtscam_osd2_probe
[    0.984000] rtscam:rtstream_init
[    0.991000] Stopped watchdog timer
[    0.998000] Started watchdog timer
[    1.004000] timer margin: 8 sec
[    1.056000] rlx snd internal codec init
[    1.064000] soc-audio soc-audio.0.auto: ASoC: machine RLX_INTERN_CARD should use snd_soc_register_card()
[    1.084000] soc-audio soc-audio.0.auto:  rlx-codec-digital <-> pcm-platform mapping ok
[    1.100000] soc-audio soc-audio.0.auto:  rlx-codec-analog <-> pcm-platform mapping ok
[    1.117000] rlx snd spdif init
[    1.123000] soc-audio soc-audio.1.auto: ASoC: machine RLX_SPDIF_CARD should use snd_soc_register_card()
[    1.143000] soc-audio soc-audio.1.auto:  rlx-spdif <-> spdif-platform mapping ok
[    1.158000] nf_conntrack version 0.5.0 (626 buckets, 2504 max)
[    1.171000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.181000] TCP: cubic registered
[    1.188000] NET: Registered protocol family 17
[    1.197000] Key type dns_resolver registered
[    1.206000] slp_flash_init
[    1.212000] Registered character driver slp_flash_chrdev
[    1.226000] ALSA device list:
[    1.232000]   #0: RLX_INTERN_CARD
[    1.238000]   #1: RLX_SPDIF_CARD
[    1.249000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    1.264000] Freeing unused kernel memory: 184K (80412000 - 80440000)
- preinit -
- init -

Please press Enter to activate this console. [    5.900000] Success to init gpio reset
[    6.048000] cryptodev: driver 1.9 loaded.
/etc/rc.common: cd: line 97: can't cd to /etc/uci-defaults
Sun Jan 19 08:01:59 UTC 2020
open /dev/crypto success
close /dev/crypto
[   10.295000] leds-gpio leds-gpio: pins are not configured from the driver
[main:35] Success to start audiopaly
Starting wlan-manager: wlan-manager started.
[   13.216000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   13.344000] usb 1-1: New USB device found, idVendor=0bda, idProduct=f179
[   13.358000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   13.372000] usb 1-1: Product: 802.11n NIC
[   13.380000] usb 1-1: Manufacturer: Realtek
[   13.389000] usb 1-1: SerialNumber: FFE04CB82100
[   15.137000] wlan-manager: insmod 8188fu.ko...
[   16.051000] usbcore: registered new interface driver rtl8188fu
1579417331917|527|4|cloud.c:91:main| - cloud-sdk version: 1.3.9-rc04, build_time:20190705_181313
**************************************************
********************config dump*******************
--------------------------------------------------
sef domain                      : n-deventry-dcipc.tplinkcloud.com
sef port                        : 443
cloud svr default port          : 443
default svr                     : n-devs-dcipc.tplinkcloud.com
default port                    : 443
default valid time              : 172800
heartbeat interval              : 30000
request timeout                 : 5000
reconnect timewait max          : 1024000
reconnect cachedsvr max times   : 5
reconnect defaultsvr max times  : 5
reconnect random time min       : 2000
reconnect random time max       : 256000
short connect interval          : 259200000
max message number              : 1000
max client number               : 20
service file                    : /etc/cloud-sdk/cloud_service.cfg
cer file                        : /etc/cloud-sdk/2048_newroot.cer
ssl verify CN                   : 
ssl verify time                 : 0
**************************************************
[   19.976000] device eth0 entered promiscuous mode
[   19.988000] br-wan: port 1(eth0) entered forwarding state
[   19.999000] br-wan: port 1(eth0) entered forwarding state
10-wifi-ethernet-switch: boot not done, don't switch
[   22.000000] br-wan: port 1(eth0) entered forwarding state
/etc/rc.common: line 1: can't create null: Read-only file system
open /dev/crypto success
1579417335352|680|3|cloud_api.c:33:cloud_api_init| - cloud-sdk version: 1.3.9-rc04, build_time:20190705_181313
not in ap mode, remove nf_conntrack_ipv4
not in ap mode, no need to load ap_filter
Generating RSA private key, 1024 bit long modulus
Generating selfsigned certificate with subject 'C=CN;ST=China;L=China;CN=TP-Link;' and validity 2020-01-19 07:02:17-2029-11-27 07:02:17
now start cet...
Command failed: Unknown error
[storage] create_and_init_shm([   27.989000] rtscam:begin to load fw from C200_V1_SC2232H_FW.bin
134). creating initial shm...
[   28.006000] rtscam:Load firmware size : 131024.
[storage] create_and_init_shm(137). shm creating succeeded, id: 65538, len:16960
[storage] create_and_init_shm(148). shm mapped @0x776a4000.
[storage] create_and_init_sem(175). creating initial sem...
[storage] wait_till_fs_ready(64). jffs is ready.
== SENSOR TYPE: SC2232H. ==
[   28.074000] rtscam:Found ISP 1.011 device
umount: can't umount /tmp/mnt/harddisk_1: No such file or directory
 [storage] formatted_exec(70). system function error :No such file or directory

 [storage] do_umount(211). No such file or directory
[   28.336000] rtscam:video device <rts3903-isp> registered
[   28.348000] rtscam:rts3903-isp initialized
cannot find dbg_iomem, create it...
[get_model_profile]-759: sensor: SC2232H, load config: /tmp/base-files/etc/dn_switch_SC2232H.ini
C200 1.0:smartir_enable
C200 1.0:smartir_level
name=C200 1.0
led_cnt=1
with_ldr=0
irt_comm[0]={200,50}
irt_comm[1]={170,40}
irt_comm[2]={140,30}
irt_comm[3]={120,18}
irt_comm[4]={100,6}
irt_comm[5]={80,4}
irt_comm[6]={60,2}
irt_comm[7]={55,1}
ir_cut_gpio_num=3
ir_led_gpio_num=9
irt_ncomm={100,6}
ir_delay=5
gain_I={0.973585,0.977537}
gain_N={1.277540,1.768843}
natural_rate_thresh=0.050000
thresh_no_adc={1500,1200,900,630,440,160,60,20}
day_ae_compensation={0,0,0,0,0,0,0,0}
day_ae_antiflicker_enable=1
day_ae_antiflicker_freq=50
night_ae_compensation=0
night_ae_antiflicker_enable=0
day_drc_asymmetry={20,17,14,11,8,4,0,0}
night_drc_asymmetry={0,0,0,0,0,5,15,0}
ae_gain_level={0,2,4,8,16,32,64,128}
smartir_enable=0
smartir_level=30
day_auto_wdr_level=60
night_auto_wdr_level=60
sleep: invalid number '0.1'
Invalid sdcard device /dev/mmcblk0, please check configuration.
[storage] formatted_exec(70). system function error :No such file or directory

[storage] uci_load_single_disk(530). mounting disk 1 failed
open /dev/crypto success
[storage] update_disk_status_for_cet(339). ubus_lookup_id update_disk_status failed

stream0 roi attr: 0 0 0 0 0 0
stream1 roi attr: 0 0 0 0 0 0
video_init done
[buffer_pool_alloc]-304: buffer audio queue id.

[storage] init_stm_files_structure(144). sizeof(struct stm_file) = 72
[storage] open_shm(305). exit open shm(shmprt:0x77f6d000  shmlen:16960  flag = 0x1b6).
[storage] open_sem(333). exit open sem(semid:32769, flag:0x1b4).
[storage] data_sync_handle_thread(186). register signal handler on thread:0x7626e500
[record_create]-5343: The adjusting time is: 1579417343
[bq_register_record]-676: bq_register_record chn: 0, stream_t: 0, tid: 1981736192

[storage] stm_open(1807). [0] stm_fd is allocated. channel = 0, type = video, flags = 0x1, mode = 0x1
[record_stop]-3597: Record stop time is: 1579417343
[storage] update_disk_status_for_cet(339). ubus_lookup_id update_disk_status failed

[input_h264_ch0_device_init]-423: Init H264 video device H264-ch0
[input_h264_ch1_device_init]-470: Init H264 video device H264-ch1
input_sound_device_init done
bufq[0]: empty sig list. create one. The first thread id is 1980687616
bufq[1]: empty sig list. create one. The first thread id is 1980687616
bufq[2]: empty sig list. create one. The first thread id is 1980687616
[main]-1038: Server begin eventloop
[cet_ubus_init]-5503: connected as ba598f06

[motord_ubus_call]-250: Failed to ubus lookup id, et = 4

[motor_reload_TT_config]-295: motor_reload_TT_config(295):motor reloadTargetTrackConfig failed

Play this stream using the URL "rtsp://192.168.0.45/stream1"
Play this stream using the URL "rtsp://192.168.0.45/stream2"
[denoise_intf_create 147] denoise library. version: 1.3. time: 2019-12-27
Table address = 0 
8000 AECNS is created sucessfully 
Sound goto normal mode
[record_stop]-3597: Record stop time is: 1579417344
[cal_reboot_interval]-97: current time is : Sun Jan 19 08:02:26 2020
, remain 68254 sec to autoreboot

[2020-01-19 08:02:26] nvid.c:main:150 - nvid started
[2020-01-19 08:02:26] nvid.c:main:172 - signal_handler succeed
[2020-01-19 08:02:26] nvid.c:main:193 - begin start onvif
[dn_switch_ctrl_vda]-1377: call vda disable/enable md/od failed
boot_done: mode_switch to wifi
[2020-01-19 08:02:27] nvid.c:main:200 - start onvif succeed
[2020-01-19 08:02:27] nvid.c:main:214 - begin uloop run
[dn_switch_ctrl_vda]-1377: call vda disable/enable md/od failed
[image_light_freq_mode_set]-1242: light freq mode:3

[2020-01-19 08:02:27] main:818 - ir_state:1
vda_ubus_register_dn_switch_event_handler 674
[initialize 25] libsmart init. version: 1.0
switch to wifi...
--------call dhcp restart----
killall: udhcpc: no process killed
----------udhcpc start with 192.168.0.45--------
update_network does nothing
switch done
[   37.148000] wlan-manager: start sta...
[   37.160000] wlan-manager: ifconfig wlan0 up.
[   38.160000] device wlan0 entered promiscuous mode
[   38.172000] br-wan: port 2(wlan0) entered forwarding state
[   38.183000] br-wan: port 2(wlan0) entered forwarding state
update without switch...
switch done
===insmod /lib/modules/3.10.27/gpio-motor.ko===
[   40.163000] Registered character driver x-motor
[   40.178000] Registered character driver y-motor
[   40.187000] br-wan: port 2(wlan0) entered forwarding state
1579417352809|527|3|cloud_ip_list.c:56:cloud_ip_list_parse| - get addr info error, host:n-deventry-dcipc.tplinkcloud.com, serv:443, Name or service not known
1579417352809|527|3|cloud_session.c:1350:cloud_session_connect_sef| - fail to parse the domain:n-deventry-dcipc.tplinkcloud.com:443
1579417352809|527|3|cloud_session.c:356:cloud_session_active_long_time| - fail to connect the SEF, result:-1
[   42.703000] recv eapol packet
[   42.712000] send eapol packet
[   42.723000] recv eapol packet
[   42.730000] send eapol packet
get dns form static dhcp:192.168.0.1, prev_append_dns:192.168.0.1
no need to set append_dns
Function is:checkDeviceBindStatus, Line is:1047.cloud device has been bind to cloud account.
[storage] set_dev_bind_status(237). STM: device bind status: 1