forked from adafruit/Adafruit_BME280_Library
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathAdafruit_BME280.h
162 lines (131 loc) · 4.93 KB
/
Adafruit_BME280.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#ifndef __BME280_H__
#define __BME280_H__
#if (ARDUINO >= 100)
#include "Arduino.h"
#else
#include "WProgram.h"
#endif
#include <Adafruit_Sensor.h>
#include <Wire.h>
/*=========================================================================
I2C ADDRESS/BITS
-----------------------------------------------------------------------*/
#define BME280_ADDRESS (0x77)
/*=========================================================================*/
/*=========================================================================
REGISTERS
-----------------------------------------------------------------------*/
enum
{
BME280_REGISTER_DIG_T1 = 0x88,
BME280_REGISTER_DIG_T2 = 0x8A,
BME280_REGISTER_DIG_T3 = 0x8C,
BME280_REGISTER_DIG_P1 = 0x8E,
BME280_REGISTER_DIG_P2 = 0x90,
BME280_REGISTER_DIG_P3 = 0x92,
BME280_REGISTER_DIG_P4 = 0x94,
BME280_REGISTER_DIG_P5 = 0x96,
BME280_REGISTER_DIG_P6 = 0x98,
BME280_REGISTER_DIG_P7 = 0x9A,
BME280_REGISTER_DIG_P8 = 0x9C,
BME280_REGISTER_DIG_P9 = 0x9E,
BME280_REGISTER_DIG_H1 = 0xA1,
BME280_REGISTER_DIG_H2 = 0xE1,
BME280_REGISTER_DIG_H3 = 0xE3,
BME280_REGISTER_DIG_H4 = 0xE4,
BME280_REGISTER_DIG_H5 = 0xE5,
BME280_REGISTER_DIG_H6 = 0xE7,
BME280_REGISTER_CHIPID = 0xD0,
BME280_REGISTER_VERSION = 0xD1,
BME280_REGISTER_SOFTRESET = 0xE0,
BME280_REGISTER_CAL26 = 0xE1, // R calibration stored in 0xE1-0xF0
BME280_REGISTER_CONTROLHUMID = 0xF2,
BME280_REGISTER_CONTROL = 0xF4,
BME280_REGISTER_CONFIG = 0xF5,
BME280_REGISTER_PRESSUREDATA = 0xF7,
BME280_REGISTER_TEMPDATA = 0xFA,
BME280_REGISTER_HUMIDDATA = 0xFD,
};
/*=========================================================================*/
/*=========================================================================
CALIBRATION DATA
-----------------------------------------------------------------------*/
typedef struct
{
uint16_t dig_T1;
int16_t dig_T2;
int16_t dig_T3;
uint16_t dig_P1;
int16_t dig_P2;
int16_t dig_P3;
int16_t dig_P4;
int16_t dig_P5;
int16_t dig_P6;
int16_t dig_P7;
int16_t dig_P8;
int16_t dig_P9;
uint8_t dig_H1;
int16_t dig_H2;
uint8_t dig_H3;
int16_t dig_H4;
int16_t dig_H5;
int8_t dig_H6;
} bme280_calib_data;
/*=========================================================================*/
/*
class Adafruit_BME280_Unified : public Adafruit_Sensor
{
public:
Adafruit_BME280_Unified(int32_t sensorID = -1);
bool begin(uint8_t addr = BME280_ADDRESS);
void getTemperature(float *temp);
void getPressure(float *pressure);
float pressureToAltitude(float seaLevel, float atmospheric, float temp);
float seaLevelForAltitude(float altitude, float atmospheric, float temp);
void getEvent(sensors_event_t*);
void getSensor(sensor_t*);
private:
uint8_t _i2c_addr;
int32_t _sensorID;
};
*/
class Adafruit_BME280
{
public:
Adafruit_BME280(void);
Adafruit_BME280(int8_t cspin);
Adafruit_BME280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin);
bool begin(uint8_t addr = BME280_ADDRESS);
float readTemperature(void);
float readPressure(void);
float readHumidity(void);
float readAltitude(float seaLevel);
private:
void readCoefficients(void);
uint8_t spixfer(uint8_t x);
void write8(byte reg, byte value);
uint8_t read8(byte reg);
uint16_t read16(byte reg);
uint32_t read24(byte reg);
int16_t readS16(byte reg);
uint16_t read16_LE(byte reg); // little endian
int16_t readS16_LE(byte reg); // little endian
uint8_t _i2caddr;
int32_t _sensorID;
int32_t t_fine;
int8_t _cs, _mosi, _miso, _sck;
bme280_calib_data _bme280_calib;
};
#endif