forked from Ralim/IronOS
-
Notifications
You must be signed in to change notification settings - Fork 0
/
configuration.h
262 lines (217 loc) · 8.76 KB
/
configuration.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
#ifndef CONFIGURATION_H_
#define CONFIGURATION_H_
#include "Settings.h"
#include <stdint.h>
/**
* Configuration.h
* Define here your default pre settings for TS80(P) or TS100
*
*/
//===========================================================================
//============================= Default Settings ============================
//===========================================================================
/**
* Default soldering temp is 320.0 C
* Temperature the iron sleeps at - default 150.0 C
*/
#define SLEEP_TEMP 150 // Default sleep temperature
#define BOOST_TEMP 420 // Default boost temp.
#define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable
/**
* Blink the temperature on the cooling screen when its > 50C
*/
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable
/**
* How many seconds/minutes we wait until going to sleep/shutdown.
* Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
*/
#define SLEEP_TIME 5 // x10 Seconds
#define SHUTDOWN_TIME 10 // Minutes
/**
* Auto start off for safety.
* Pissible values are:
* 0 - none
* 1 - Soldering Temperature
* 2 - Sleep Temperature
* 3 - Sleep Off Temperature
*/
#define AUTO_START_MODE 0 // Default to none
/**
* Locking Mode
* When in soldering mode a long press on both keys toggle the lock of the buttons
* Possible values are:
* 0 - Desactivated
* 1 - Lock except boost
* 2 - Full lock
*/
#define LOCKING_MODE 0 // Default to desactivated for safety
/**
* OLED Orientation
*
*/
#define ORIENTATION_MODE 2 // 0: Right 1:Left 2:Automatic - Default Automatic
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change
/**
* OLED Brightness
*
*/
#define MIN_BRIGHTNESS 0 // Min OLED brightness selectable
#define MAX_BRIGHTNESS 100 // Max OLED brightness selectable
#define BRIGHTNESS_STEP 25 // OLED brightness increment
#define DEFAULT_BRIGHTNESS 25 // default OLED brightness
/**
* Temp change settings
*/
#define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1
#define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
#define TEMP_CHANGE_LONG_STEP_MAX 90 // Temp change long step MAX value
/* Power pulse for keeping power banks awake*/
#define POWER_PULSE_INCREMENT 1
#define POWER_PULSE_MAX 100 // x10 max watts
#define POWER_PULSE_WAIT_MAX 9 // 9*2.5s = 22.5 seconds
#define POWER_PULSE_DURATION_MAX 9 // 9*250ms = 2.25 seconds
#ifdef MODEL_TS100
#define POWER_PULSE_DEFAULT 0
#else
#define POWER_PULSE_DEFAULT 5
#endif /* TS100 */
#define POWER_PULSE_WAIT_DEFAULT 4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s
#define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms
/**
* OLED Orientation Sensitivity on Automatic mode!
* Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
*/
#define SENSITIVITY 7 // Default 7
/**
* Detailed soldering screen
* Detailed idle screen (off for first time users)
*/
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
#define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0
#define THERMAL_RUNAWAY_TIME_SEC 20
#define THERMAL_RUNAWAY_TEMP_C 10
#define CUT_OUT_SETTING 0 // default to no cut-off voltage
#define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33))
#define TEMPERATURE_INF 0 // default to 0
#define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow
#define ANIMATION_LOOP 1 // 0: off 1: on
#define ANIMATION_SPEED settingOffSpeed_t::MEDIUM
#define OP_AMP_Rf_TS100 750 * 1000 // 750 Kilo-ohms -> From schematic, R1
#define OP_AMP_Rin_TS100 2370 // 2.37 Kilo-ohms -> From schematic, R2
#define OP_AMP_GAIN_STAGE_TS100 (1 + (OP_AMP_Rf_TS100 / OP_AMP_Rin_TS100))
#define OP_AMP_Rf_TS80 180 * 1000 // 180 Kilo-ohms -> From schematic, R6
#define OP_AMP_Rin_TS80 2000 // 2.0 Kilo-ohms -> From schematic, R3
#define OP_AMP_GAIN_STAGE_TS80 (1 + (OP_AMP_Rf_TS80 / OP_AMP_Rin_TS80))
#define ADC_MAX_READING (4096 * 8) // Maximum reading of the adc
#define ADC_VDD_MV 3300 // ADC max reading millivolts
#define POW_PD_EXT 0
// Deriving the Voltage div:
// Vin_max = (3.3*(r1+r2))/(r2)
// vdiv = (32768*4)/(vin_max*10)
#if defined(MODEL_TS100) + defined(MODEL_TS80) + defined(MODEL_TS80P) + defined(MODEL_TS101) > 1
#error "Multiple models defined!"
#elif defined(MODEL_TS100) + defined(MODEL_TS80) + defined(MODEL_TS80P) + defined(MODEL_TS101) == 0
#error "No model defined!"
#endif
#define NEEDS_VBUS_PROBE 0
// Miniware is swapping IMU's around a bit now, so we turn them all on
#define ACCEL_MMA
#define ACCEL_LIS
#define ACCEL_SC7
#define ACCEL_MSA
#define ACCEL_BMA
#define MIN_CALIBRATION_OFFSET 100 // Min value for calibration
#define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C
#define PID_TIM_HZ (8) // Tick rate of the PID loop
#define MAX_TEMP_C 450 // Max soldering temp selectable °C
#define MAX_TEMP_F 850 // Max soldering temp selectable °F
#define MIN_TEMP_C 10 // Min soldering temp selectable °C
#define MIN_TEMP_F 50 // Min soldering temp selectable °F
#define MIN_BOOST_TEMP_C 250 // The min settable temp for boost mode °C
#define MIN_BOOST_TEMP_F 480 // The min settable temp for boost mode °F
#ifdef MODEL_TS100
#define VOLTAGE_DIV 467 // 467 - Default divider from schematic
#define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV
#define PID_POWER_LIMIT 70 // Sets the max pwm power limit
#define POWER_LIMIT 0 // 0 watts default limit
#define MAX_POWER_LIMIT 70
#define POWER_LIMIT_STEPS 5
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS100
#define TEMP_uV_LOOKUP_HAKKO
#define USB_PD_VMAX 20 // Maximum voltage for PD to negotiate
#define HARDWARE_MAX_WATTAGE_X10 750
#define TIP_THERMAL_MASS 65 // X10 watts to raise 1 deg C in 1 second
#define TIP_RESISTANCE 75 // x10 ohms, 7.5 typical for ts100 tips
#define POW_DC
#define TEMP_TMP36
#endif /* TS100 */
#ifdef MODEL_TS101
#define VOLTAGE_DIV 700 // 700 - Default divider from schematic
#define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV
#define PID_POWER_LIMIT 100 // Sets the max pwm power limit
#define POWER_LIMIT 0 // 0 watts default limit
#define MAX_POWER_LIMIT 100
#define POWER_LIMIT_STEPS 5
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS100
#define TEMP_uV_LOOKUP_HAKKO
#define HARDWARE_MAX_WATTAGE_X10 1000
#define TIP_THERMAL_MASS 65 // X10 watts to raise 1 deg C in 1 second
#define TIP_RESISTANCE 75 // x10 ohms, 7.5 typical for ts100 tips
#define TIP_HAS_DIRECT_PWM 1
#define POW_DC 1
#define POW_PD 1
#define I2C_SOFT_BUS_2 1
#define I2C_SOFT_BUS_1 1
#define OLED_I2CBB1 1
#define USB_PD_I2CBB2 1
#define USB_PD_VMAX 28 // Device supposedly can do 28V; looks like vmax is 33 ish
#define OLED_128x32 1
#define OLED_FLIP 1
#define HAS_SPLIT_POWER_PATH 1
#define TEMP_NTC 1
#define ACCEL_I2CBB1 1
#define POW_EPR 1
#define HAS_POWER_DEBUG_MENU
#define DEBUG_POWER_MENU_BUTTON_B
#endif /* TS101 */
#if defined(MODEL_TS80) + defined(MODEL_TS80P) > 0
#define MAX_POWER_LIMIT 40
#define POWER_LIMIT_STEPS 2
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS80
#define TEMP_uV_LOOKUP_TS80
#define USB_PD_VMAX 12 // Maximum voltage for PD to negotiate
#define TIP_THERMAL_MASS 40
#define TIP_RESISTANCE 45 // x10 ohms, 4.5 typical for ts80 tips
#define LIS_ORI_FLIP
#define OLED_FLIP
#endif /* TS80(P) */
#ifdef MODEL_TS80
#define VOLTAGE_DIV 780 // Default divider from schematic
#define CALIBRATION_OFFSET 900 // the adc offset in uV
#define PID_POWER_LIMIT 35 // Sets the max pwm power limit
#define POWER_LIMIT 32 // 24 watts default power limit
#define HARDWARE_MAX_WATTAGE_X10 320
#define POW_QC
#define TEMP_TMP36
#endif /* TS80 */
#ifdef MODEL_TS80P
#define VOLTAGE_DIV 650 // Default for TS80P with slightly different resistors
#define CALIBRATION_OFFSET 1500 // the adc offset in uV
#define PID_POWER_LIMIT 35 // Sets the max pwm power limit
#define POWER_LIMIT 32 // 30 watts default power limit
#define HARDWARE_MAX_WATTAGE_X10 320
#define POW_PD 1
#define POW_QC 1
#define TEMP_NTC
#define I2C_SOFT_BUS_2 1
#define SC7_ORI_FLIP
#endif /* TS80P */
#ifdef MODEL_TS101
#define FLASH_LOGOADDR (0x08000000 + (126 * 1024))
#define SETTINGS_START_PAGE (0x08000000 + (127 * 1024))
#else
#define FLASH_LOGOADDR (0x08000000 + (62 * 1024))
#define SETTINGS_START_PAGE (0x08000000 + (63 * 1024))
#endif /* TS101 */
#endif /* CONFIGURATION_H_ */