In this section, we’ll go over setting up the Raspberry Pi (RPi) and setting up all the code that will run the rover. Our rover uses ROS (Robotic Operating System), which will be installed on your choice of operating system; we will set these up below.
These instructions should work for both the RPi 3 and 4. You are free to use other versions of RPi, ROS, or OS, but setting these up is not covered here and it is not guaranteed that those will work.
The first step is to install the Ubuntu Operating System on your Raspberry Pi.
Download Ubuntu 18.04 from here for your RPi version. For an RPi3 the best default is 32-bit, but if you're on an Rpi4 then you can go for 64-bit.
Preparing the image for the RPi and boot it up:
- Flash Ubuntu onto your microSD card. There are instructions for doing this on Ubuntu, Windows, and Mac
- Attach a monitor and keyboard to the RPi (note an alternative is to use
screen, see here) - Insert the flashed SD card in the RPi
- Power it on
- Login, using "ubuntu" for the username and password. You should be prompted to make a new password.
You should now be logged in to your newly minted copy of Ubuntu 18.04!
Get your new device on the internet. Instructions here.
- Basically, you need to edit the
/etc/netplan/50-cloud-init.yamlfile and add your wifi network) SSID-NAME-HEREis your network's name, andPASSWORD-HEREis the password for it.- After following these steps, you should see an ip address assigned in the output of
ip a. It will be aninetvalue like192.168.1.18, underneath an interface entry likewlan0
This is a good option for newbies to the linux world. It's pretty easy to do, though it'll take a while (maybe an hour).
Follow the instructions here.
- We recommend using SLiM as the Display Manager, it seems lighter weight than the other options
- We also recommend using GNOME for the GUI
- Note that you'll probably need to
sudo tasksel(instead of without sudo, per the instructions), otherwise you'll get a permissions error.
You probably will also want to connect to your newly configured RPi remotely over ssh, rather than having to using a separate monitor every time. Instructions here.
- Basically, run
sudo systemctl enable ssh.socketfrom the command line - Now you should be able to login from your dev machine.
ssh [email protected], using the ip address for your RPi that you found above. - It should prompt you for a password. Once you enter it successfully, you'll be logged on! The
enablestep above should configure the ssh server to automatically come up on reboot, so you can just login to the RPi remotely from now on.
We'll install ROS (Robot Operating System) Melodic on the RPi.
You'll need to be logged in to the RPi via ssh, or open a terminal in the desktop GUI if you installed it above.
The below steps are based off of these instructions. Consult them for more details.
Setup
# Setup your computer to accept software from packages.ros.org
sudo sh -c 'echo "deb http://packages.ros.org/ros/ubuntu $(lsb_release -sc) main" > /etc/apt/sources.list.d/ros-latest.list'
# set up keys
sudo apt-key adv --keyserver 'hkp://keyserver.ubuntu.com:80' --recv-key C1CF6E31E6BADE8868B172B4F42ED6FBAB17C654
Installation
# make sure your Debian package index is up-to-date
sudo apt update
# desktop-Full Install: (Recommended) : ROS, rqt, rviz, robot-generic libraries, 2D/3D simulators and 2D/3D perception
sudo apt install ros-melodic-desktop-full
Dependencies for building packages
# install 'em
sudo apt install python-rosdep python-rosinstall python-rosinstall-generator python-wstool build-essential
# initialize rosdep
sudo rosdep init
rosdep update
First we'll create a workspace for the rover code.
# Create a catkin workspace directory, which will contain all ROS compilation and
# source code files, and move into it
mkdir -p ~/osr_ws/src && cd ~/osr_ws
# Source your newly created ROS environment
source /opt/ros/melodic/setup.bash
For this section, you'll be working with the version control software git. Now's a good time to read up on how that works if you're new to it and make a GitHub account!
In the newly created catkin workspace you just made, clone this repo:
sudo apt-get install git
cd ~/osr_ws/src
git clone https://github.com/nasa-jpl/osr-rover-code.git
# install the dependencies
cd ..
rosdep install --from-paths src --ignore-src
catkin_make
# add the generated files to the path so ROS can find them
source devel/setup.bash
The rover has some customizable settings that will overwrite the default values. Whether you have any changes compared to the defaults or not, you have to manually create these files:
cd ~/osr_ws/src/osr-rover-code/ROS/osr_bringup/config
touch physical_properties_mod.yaml roboclaw_params_mod.yaml
To change any values from the default, modify these files (the _mod.yaml ones) instead so your changes don't get committed to git. The files follow the same structure as the default. Just include the values that you need to change as the default values for other parameters may change over time.
You might also want to modify the file osr-rover-code/ROS/osr_bringup/launch/osr.launch to change the velocities the gamepad controller will
send to the rover. These values in the node joy2twist are of interest:
<param name="scale_linear" value="0.18"/>
<param name="scale_angular" value="0.4"/>
<param name="scale_linear_turbo" value="0.24"/>
The maximum speed your rover can go is determined by the no-load speed of your drive motors. The default no-load speed is located
in the file physical_properties.yaml as drive_no_load_rpm, unless you modified it in the corresponding _mod.yaml file.
This maximum speed corresponds to scale_linear_turbo and can be calculated as drive_no_load_rpm * 2pi / 60 * wheel radius (=0.075m).
Based on this upper limit, let's set our regular moving speed to a sensible fraction of that which you can configure to your liking.
Start with e.g. 0.75 * scale_linear_turbo. If you think it's too slow or too fast, simply scale it up or down.
The turning speed of the rover, just like a regular car, depends on how fast it's going. As a result, scale_angular
should be set to scale_linear / min_radius. For the default configuration, the min_radius equals 0.45m.
The source...foo.bash lines above are used to manually configure your ROS environment. We can do this automatically in the future by doing:
cd ~
echo "source /opt/ros/melodic/setup.bash" >> ~/.bashrc
echo "source ~/osr_ws/devel/setup.bash" >> ~/.bashrc
This adds the source lines to ~/.bashrc, which runs whenever a new shell is opened on the RPi - by logging in via ssh, for example. So, from now on, when you log into the RPi your new command line environment will have the appropriate configuration for ROS and the rover code.
The RPi will talk to the motor controllers over serial.
Because we are using the serial port for communicating with the roboclaw motor controllers, we have to disable the [email protected] service. This service has some level of control over serial devices that we use, so if we leave it on it we'll get weird errors (source). Note that the masking step was suggested here. It seems to be necessary for some setups of the rpi4 - just using systemctl disable won't cut it for disabling the service.
Note that the following will stop you from being able to communicate with the RPi over the serial, wired connection. However, it won't affect communication with the rpi with SSH over wifi.
sudo systemctl stop [email protected]
sudo systemctl disable [email protected]
sudo systemctl mask [email protected]
Now we'll need to copy over a udev rules file, which is used to configure needed device files in /dev; namely, ttyS0 and ttyAMA0. Here's a good primer on udev.
# copy udev file from the repo to your system
cd ~/osr_ws/src/osr-rover-code/config
sudo cp serial_udev_ubuntu1804.rules /etc/udev/rules.d/10-local.rules
# reload the udev rules so that the devices files are set up correctly.
sudo udevadm control --reload-rules && sudo udevadm trigger
This configuration should persist across RPi reboots.
Finally, add the user to the tty group:
sudo adduser ubuntu tty
(or whatever your username is, if not ubuntu)
You'll need to log out of your ssh session and log back in for this to take effect. Or you can restart Ubuntu.
Run the roboclawtest.py script with all of the motor addresses:
cd ~/osr_ws/src/osr-rover-code/scripts
python roboclawtest.py 128
python roboclawtest.py 129
python roboclawtest.py 130
python roboclawtest.py 131
python roboclawtest.py 132
Each of these should output something like, within a very short execution time:
(1, 'USB Roboclaw 2x7a v4.1.34\n')
(1, 853, 130)
If the script seems to hang, or returns only zeros inside the parantheses, then you have a problem communicating with the given roboclaw for that address. Some troubleshooting steps in this cases:
- Make sure you followed the instructions in the "Setting up serial communication" section above, and the serial devices are configured correctly on the RPi.
- Also make sure you went through the calibration instructions from the main repo and set the proper address, serial comm baud rate, and "Enable Multi-Unit Mode" option for every roboclaw controller (if multi-unit mode isn't enabled on every controller, there will be serial bus contention.). If you update anything on a controller, you'll need to fully power cycle it by turning the rover off.
- If you're still having trouble after the above steps, try unplugging every motor controller except for one, and debug exclusively with that one.