diff --git a/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp b/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp index 84bb7f9c4cf7..ceedd316e374 100644 --- a/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp +++ b/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp @@ -1479,7 +1479,7 @@ void unified_bed_leveling::smart_fill_mesh() { SERIAL_ECHOLNPGM("Tilting mesh (3/3)"); TERN_(HAS_STATUS_MESSAGE, ui.status_printf_P(0, PSTR(S_FMT " 3/3"), GET_TEXT(MSG_LCD_TILTING_MESH))); - measured_z = probe.probe_at_point(points[2], PROBE_PT_STOW, param.V_verbosity); + measured_z = probe.probe_at_point(points[2], PROBE_PT_LAST_STOW, param.V_verbosity); #ifdef VALIDATE_MESH_TILT z3 = measured_z; #endif diff --git a/Marlin/src/module/probe.cpp b/Marlin/src/module/probe.cpp index ded5d438934b..cbadda2eef7c 100644 --- a/Marlin/src/module/probe.cpp +++ b/Marlin/src/module/probe.cpp @@ -751,7 +751,7 @@ float Probe::probe_at_point(const_float_t rx, const_float_t ry, const ProbePtRai if (DEBUGGING(LEVELING)) { DEBUG_ECHOLNPAIR( "...(", LOGICAL_X_POSITION(rx), ", ", LOGICAL_Y_POSITION(ry), - ", ", raise_after == PROBE_PT_RAISE ? "raise" : raise_after == PROBE_PT_STOW ? "stow" : "none", + ", ", raise_after == PROBE_PT_RAISE ? "raise" : raise_after == PROBE_PT_LAST_STOW ? "stow (last)" : raise_after == PROBE_PT_STOW ? "stow" : "none", ", ", verbose_level, ", ", probe_relative ? "probe" : "nozzle", "_relative)" ); @@ -782,7 +782,7 @@ float Probe::probe_at_point(const_float_t rx, const_float_t ry, const ProbePtRai const bool big_raise = raise_after == PROBE_PT_BIG_RAISE; if (big_raise || raise_after == PROBE_PT_RAISE) do_blocking_move_to_z(current_position.z + (big_raise ? 25 : Z_CLEARANCE_BETWEEN_PROBES), z_probe_fast_mm_s); - else if (raise_after == PROBE_PT_STOW) + else if (raise_after == PROBE_PT_STOW || raise_after == PROBE_PT_LAST_STOW) if (stow()) measured_z = NAN; // Error on stow? if (verbose_level > 2) diff --git a/Marlin/src/module/probe.h b/Marlin/src/module/probe.h index ce690593f229..5da5ea3a22b6 100644 --- a/Marlin/src/module/probe.h +++ b/Marlin/src/module/probe.h @@ -33,6 +33,7 @@ enum ProbePtRaise : uint8_t { PROBE_PT_NONE, // No raise or stow after run_z_probe PROBE_PT_STOW, // Do a complete stow after run_z_probe + PROBE_PT_LAST_STOW, // Stow for sure, even in BLTouch HS mode PROBE_PT_RAISE, // Raise to "between" clearance after run_z_probe PROBE_PT_BIG_RAISE // Raise to big clearance after run_z_probe };