There are quite a few different types of bootloaders that keyboards use, and almost all of them use their own flashing method and tools. Luckily, projects like the QMK Toolbox aim to support as many of them as possible, but this article will describe the different types of bootloaders, and available methods for flashing them.
For AVR-based keyboards, QMK will automatically calculate if your .hex
file is the right size to be flashed to the device based on the BOOTLOADER
value set in rules.mk
, and output the total size in bytes (along with the max).
You will also be able to use the CLI to flash your keyboard, by running:
$ qmk flash -kb <keyboard> -km <keymap>
See the qmk flash
documentation for more information.
Atmel's DFU bootloader comes on all USB AVRs by default (except for 16/32U4RC), and is used by many keyboards that have their own ICs on their PCBs (older OLKB boards, Clueboards). Some keyboards may also use LUFA's DFU bootloader, or QMK's fork of it (newer OLKB boards), that adds in additional features specific to that hardware.
To ensure compatibility with the DFU bootloader, make sure this block is present in your rules.mk
(optionally with lufa-dfu
or qmk-dfu
instead):
# Bootloader selection
BOOTLOADER = atmel-dfu
Compatible flashers:
- QMK Toolbox (recommended GUI)
- dfu-programmer /
:dfu
target in QMK (recommended command line)dfu-programmer <mcu> erase --force dfu-programmer <mcu> flash --force <filename> dfu-programmer <mcu> reset
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Press the
QK_BOOT
keycode - Press the
RESET
button on the PCB if available - Short RST to GND quickly
- Press the
- Wait for the OS to detect the device
- Erase the flash memory (will be done automatically if using the Toolbox or CLI/
make
command) - Flash a .hex file
- Reset the device into application mode (will be done automatically as above)
QMK maintains a fork of the LUFA DFU bootloader that additionally performs a simple matrix scan for exiting the bootloader and returning to the application, as well as flashing an LED/making a ticking noise with a speaker when things are happening. To enable these features, add the following defines to your config.h
:
#define QMK_ESC_OUTPUT F1 // COL pin if COL2ROW
#define QMK_ESC_INPUT D5 // ROW pin if COL2ROW
// Optional:
//#define QMK_LED E6
//#define QMK_SPEAKER C6
Currently we do not recommend making QMK_ESC
the same key as the one designated for Bootmagic Lite, as holding it down will cause the MCU to loop back and forth between entering and exiting the bootloader.
The manufacturer and product strings are automatically pulled from config.h
, with " Bootloader" appended to the product string.
To generate this bootloader, use the bootloader
target, eg. make planck/rev4:default:bootloader
. To generate a production-ready .hex file (combining QMK and the bootloader), use the production
target, eg. make planck/rev4:default:production
.
:dfu
: Checks every 5 seconds until a DFU device is available, and then flashes the firmware.:dfu-split-left
and:dfu-split-right
: Flashes the firmware as with:dfu
, but also sets the handedness setting in EEPROM. This is ideal for Elite-C-based split keyboards.
Arduino boards and their clones use the Caterina bootloader or a variant of it (any keyboard built with a Pro Micro or clone, and the Pololu A-Star), and uses the AVR109 protocol to communicate through virtual serial.
To ensure compatibility with the Caterina bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = caterina
Compatible flashers:
- QMK Toolbox (recommended GUI)
- AVRDUDESS
- avrdude with the
avr109
programmer /:avrdude
target in QMK (recommended command line)avrdude -p <mcu> -c avr109 -P <serialport> -U flash:w:<filename>:i
Flashing sequence:
- Enter the bootloader using any of the following methods (you only have 7 seconds to flash once it enters; some variants may require you to reset twice within 750 milliseconds):
- Press the
QK_BOOT
keycode - Press the
RESET
button on the PCB if available - Short RST to GND quickly
- Press the
- Wait for the OS to detect the device
- Flash a .hex file
- Wait for the device to reset automatically
:avrdude
: Checks every 5 seconds until a Caterina device is available (by detecting a new COM port), and then flashes the firmware.:avrdude-loop
: Flashes the firmware as with:avrdude
, but after each device is flashed, will attempt to flash again. This is useful for bulk flashing. Hit Ctrl+C to escape the loop.:avrdude-split-left
and:avrdude-split-right
: Flashes the firmware as with:avrdude
, but also sets the handedness setting in EEPROM. This is ideal for Pro Micro-based split keyboards.
HalfKay is a super-slim bootloader developed by PJRC that presents itself as an HID device (which requires no additional driver), and comes preflashed on all Teensys, namely the 2.0. It is currently closed-source, and thus once overwritten (eg. via ISP flashing another bootloader), cannot be restored.
To ensure compatibility with the Halfkay bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = halfkay
Compatible flashers:
- QMK Toolbox (recommended GUI)
- Teensy Loader
- Teensy Loader Command Line /
:teensy
target in QMK (recommended command line)teensy_loader_cli -v -mmcu=<mcu> <filename>
Flashing sequence:
- Enter the bootloader using any of the following methods (you only have 7 seconds to flash once it enters):
- Press the
QK_BOOT
keycode - Press the
RESET
button on the Teensy or PCB if available - short RST to GND quickly
- Press the
- Wait for the OS to detect the device
- Flash a .hex file
- Reset the device into application mode (may be done automatically)
USBasploader is a bootloader originally by Objective Development. It emulates a USBasp ISP programmer and is used in some non-USB AVR chips such as the ATmega328P, which run V-USB.
To ensure compatibility with the USBasploader bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = usbasploader
Compatible flashers:
- QMK Toolbox (recommended GUI)
- AVRDUDESS
- avrdude with the
usbasp
programmer /:usbasp
target in QMK (recommended command line)avrdude -p <mcu> -c usbasp -U flash:w:<filename>:i
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Press the
QK_BOOT
keycode - Keep the
BOOT
button held while quickly tapping theRESET
button on the PCB
- Press the
- Wait for the OS to detect the device
- Flash a .hex file
- Press the
RESET
button on the PCB or short RST to GND
BootloadHID is a USB bootloader for AVR microcontrollers. It presents itself as an HID input device, much like HalfKay, and can therefore be run without installing any driver on Windows.
To ensure compatibility with the bootloadHID bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = bootloadhid
Compatible flashers:
- QMK Toolbox (recommended GUI)
- HIDBootFlash
- bootloadHID CLI /
:bootloadhid
target in QMK (recommended command line)bootloadHID -r <filename>
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Hold the salt key while plugging the keyboard in - for PS2AVRGB boards, this is usually the key connected to MCU pins A0 and B0, otherwise it will be documented in your keyboard's readme
- Tap the
- Wait for the OS to detect the device
- Flash a .hex file
- Reset the device into application mode (may be done automatically)
QMK maintains a fork of the LUFA HID bootloader, which uses a USB HID Endpoint for flashing in the way that the PJRC's Teensy Loader flasher and HalfKay bootloader work. Additionally, it performs a simple matrix scan for exiting the bootloader and returning to the application, as well as flashing an LED/making a ticking noise with a speaker when things are happening.
To ensure compatibility with the QMK HID bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = qmk-hid
To enable the additional features, add the following defines to your config.h
:
#define QMK_ESC_OUTPUT F1 // COL pin if COL2ROW
#define QMK_ESC_INPUT D5 // ROW pin if COL2ROW
// Optional:
//#define QMK_LED E6
//#define QMK_SPEAKER C6
Currently we do not recommend making QMK_ESC
the same key as the one designated for Bootmagic Lite, as holding it down will cause the MCU to loop back and forth between entering and exiting the bootloader.
The manufacturer and product strings are automatically pulled from config.h
, with " Bootloader" appended to the product string.
To generate this bootloader, use the bootloader
target, eg. make planck/rev4:default:bootloader
. To generate a production-ready .hex file (combining QMK and the bootloader), use the production
target, eg. make planck/rev4:default:production
.
Compatible flashers:
- TBD
- Currently, you need to either use the Python script, or compile
hid_bootloader_cli
, from the LUFA repo. Homebrew may (will) have support for this directly (viabrew install qmk/qmk/hid_bootloader_cli
).
- Currently, you need to either use the Python script, or compile
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Press the
QK_BOOT
keycode - Press the
RESET
button on the PCB if available - short RST to GND quickly
- Press the
- Wait for the OS to detect the device
- Flash a .hex file
- Reset the device into application mode (may be done automatically)
:qmk-hid
: Checks every 5 seconds until a DFU device is available, and then flashes the firmware.
All STM32 and APM32 MCUs, except for F103 (see the STM32duino section) come preloaded with a factory bootloader that cannot be modified nor deleted.
To ensure compatibility with the STM32-DFU bootloader, make sure this block is present in your rules.mk
(optionally with apm32-dfu
instead):
# Bootloader selection
BOOTLOADER = stm32-dfu
Compatible flashers:
- QMK Toolbox (recommended GUI)
- dfu-util /
:dfu-util
target in QMK (recommended command line)dfu-util -a 0 -d 0483:DF11 -s 0x8000000:leave -D <filename>
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode (may not work on STM32F042 devices) - If a reset circuit is present, tap the
RESET
button on the PCB; some boards may also have a toggle switch that must be flipped - Otherwise, you need to bridge
BOOT0
to VCC (viaBOOT0
button or jumper), shortRESET
to GND (viaRESET
button or jumper), and then let go of theBOOT0
bridge
- Tap the
- Wait for the OS to detect the device
- Flash a .bin file
- Reset the device into application mode (may be done automatically)
:dfu-util
: Waits until an STM32 bootloader device is available, and then flashes the firmware.:dfu-util-split-left
and:dfu-util-split-right
: Flashes the firmware as with:dfu-util
, but also sets the handedness setting in EEPROM. This is ideal for Proton-C-based split keyboards.:st-link-cli
: Allows you to flash the firmware via the ST-Link CLI utility, rather than dfu-util. Requires an ST-Link dongle.:st-flash
: Allows you to flash the firmware via thest-flash
utility from STLink Tools, rather than dfu-util. Requires an ST-Link dongle.
This bootloader is used almost exclusively for STM32F103 boards, as they do not come with a USB DFU bootloader. The source code and prebuilt binaries can be found here.
To ensure compatibility with the STM32duino bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = stm32duino
Compatible flashers:
- QMK Toolbox (recommended GUI)
- dfu-util /
:dfu-util
target in QMK (recommended command line)dfu-util -a 2 -d 1EAF:0003 -D <filename>
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - If a reset circuit is present, tap the
RESET
button on the PCB - Otherwise, you need to bridge
BOOT0
to VCC (viaBOOT0
button or jumper), shortRESET
to GND (viaRESET
button or jumper), and then let go of theBOOT0
bridge
- Tap the
- Wait for the OS to detect the device
- Flash a .bin file
- Reset the device into application mode (may be done automatically)
Keyboards produced by Input Club use NXP Kinetis microcontrollers rather than STM32, and come with their own custom bootloader, however the process and protocol is largely the same.
The rules.mk
setting for this bootloader is kiibohd
, but since this bootloader is limited to Input Club boards, it should not be necessary to set at keymap or user level.
Compatible flashers:
- QMK Toolbox (recommended GUI)
- dfu-util /
:dfu-util
target in QMK (recommended command line)dfu-util -a 0 -d 1C11:B007 -D <filename>
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Press the
RESET
button on the PCB
- Tap the
- Wait for the OS to detect the device
- Flash a .bin file
- Reset the device into application mode (may be done automatically)
Some keyboards produced for several commercial brands (GMMK, Akko, MonsGeek, Inland) use this bootloader. The wb32-dfu-updater
utility is bundled with QMK MSYS and Glorious's build of QMK Toolbox. If neither of these flashing methods is available for your OS, you will likely need to compile the CLI version from source.
The info.json
setting for this bootloader is wb32-dfu
.
Compatible flashers:
- Glorious's build of QMK Toolbox (recommended GUI)
- wb32-dfu-updater_cli /
:flash
target in QMK (recommended command line)wb32-dfu-updater_cli -t -s 0x8000000 -D <filename>
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Press the
RESET
button on the PCB
- Tap the
- Wait for the OS to detect the device
- Flash a .bin file
- Reset the device into application mode (may be done automatically)
Keyboards may opt into supporting the tinyuf2 bootloader. This is currently only supported on F303/F401/F411.
The rules.mk
setting for this bootloader is tinyuf2
, and can be specified at the keymap or user level.
To ensure compatibility with the tinyuf2 bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = tinyuf2
Compatible flashers:
- Any application able to copy a file from one place to another, such as macOS Finder or Windows Explorer.
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Double-tap the
nRST
button on the PCB.
- Tap the
- Wait for the OS to detect the device
- Copy the .uf2 file to the new USB disk
- Wait for the keyboard to become available
or
CLI Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Double-tap the
nRST
button on the PCB.
- Tap the
- Wait for the OS to detect the device
- Flash via QMK CLI eg.
qmk flash --keyboard handwired/onekey/blackpill_f411_tinyuf2 --keymap default
- Wait for the keyboard to become available
:uf2-split-left
and:uf2-split-right
: Flashes the firmware but also sets the handedness setting in EEPROM by generating a side specific firmware.
Keyboards may opt into supporting the uf2boot bootloader. This is currently only supported on F103.
The rules.mk
setting for this bootloader is uf2boot
, and can be specified at the keymap or user level.
To ensure compatibility with the uf2boot bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = uf2boot
Compatible flashers:
- Any application able to copy a file from one place to another, such as macOS Finder or Windows Explorer.
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Double-tap the
nRST
button on the PCB.
- Tap the
- Wait for the OS to detect the device
- Copy the .uf2 file to the new USB disk
- Wait for the keyboard to become available
or
CLI Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Double-tap the
nRST
button on the PCB.
- Tap the
- Wait for the OS to detect the device
- Flash via QMK CLI eg.
qmk flash --keyboard handwired/onekey/bluepill_uf2boot --keymap default
- Wait for the keyboard to become available
:uf2-split-left
and:uf2-split-right
: Flashes the firmware but also sets the handedness setting in EEPROM by generating a side specific firmware.
The rules.mk
setting for this bootloader is rp2040
, and can be specified at the keymap or user level.
To ensure compatibility with the rp2040 bootloader, make sure this block is present in your rules.mk
:
# Bootloader selection
BOOTLOADER = rp2040
Compatible flashers:
- Any application able to copy a file from one place to another, such as macOS Finder or Windows Explorer.
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Hold the
BOOTSEL
button on the PCB while plugin in the usb cable. - Double-tap the
RESET
button on the PCB1.
- Tap the
- Wait for the OS to detect the device
- Copy the .uf2 file to the new USB disk
- Wait for the keyboard to become available
or
CLI Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
QK_BOOT
keycode - Hold the
BOOTSEL
button on the PCB while plugin in the usb cable. - Double-tap the
RESET
button on the PCB1.
- Tap the
- Wait for the OS to detect the device
- Flash via QMK CLI eg.
qmk flash --keyboard handwired/onekey/rpi_pico --keymap default
- Wait for the keyboard to become available
1: This works only if the controller has been flashed with QMK Firmware with RP2040_BOOTLOADER_DOUBLE_TAP_RESET
defined.